Buying guide · Intermediate · 3 min read
ABS, ASA and HIPS Filament
Strong, Heat-Resistant Prints
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
ABS and ASA are tough, heat-resistant plastics for functional parts; ASA also survives sunlight outdoors. HIPS is a support material that dissolves in limonene. All three warp and give off fumes, so print in an enclosure on a hot bed with good ventilation. Expect nozzle 240 to 260 °C and bed 90 to 110 °C.
Key specs at a glance
- ABS
- Tough, heat resistant, vapour smoothable with acetone; yellows in sunlight
- ASA
- Like ABS but UV and weather resistant, good outdoors
- HIPS
- Dissolvable support for ABS in limonene; also prints as a plain material
- Nozzle
- Typically 230 to 260 °C
- Bed
- Typically 90 to 110 °C
- Enclosure
- Strongly recommended to prevent warping
ABS vs ASA vs HIPS
They are chemical cousins with different strengths.
| Material | Best for | Strength | Weak point |
|---|---|---|---|
| ABS | Brackets, housings, car interior parts, parts that need to be glued or smoothed | Tough, impact resistant | Warps, fumes, UV yellowing |
| ASA | Outdoor enclosures, drone parts, garden items, car exterior parts | Same as ABS plus UV and weather resistance | Needs similar care to ABS |
| HIPS | Support material for ABS and ASA, lightweight models | Dissolves in limonene | Not as strong as ABS for final parts |
- ABS
- Best for:
- Brackets, housings, car interior parts, parts that need to be glued or smoothed
- Strength:
- Tough, impact resistant
- Weak point:
- Warps, fumes, UV yellowing
- ASA
- Best for:
- Outdoor enclosures, drone parts, garden items, car exterior parts
- Strength:
- Same as ABS plus UV and weather resistance
- Weak point:
- Needs similar care to ABS
- HIPS
- Best for:
- Support material for ABS and ASA, lightweight models
- Strength:
- Dissolves in limonene
- Weak point:
- Not as strong as ABS for final parts
Printer setup
needs to reach 90 to 110 °C; a PEI plate or glue stick helps hold the first layer (PEI plates).
keeps the air warm and stops draughts that curl the corners (enclosures).
ABS and ASA release styrene. Print in a ventilated room or vent the enclosure outside, and do not sit next to a running printer for hours.
needed for temperatures above about 240 °C; PTFE-lined hotends break down when run that hot (hotends).
Starting settings
Check the label, then begin here.
| Setting | Starting point |
|---|---|
| Nozzle | ABS 240 to 255 °C, ASA 245 to 260 °C, HIPS 230 to 250 °C |
| Bed | 100 to 110 °C |
| Cooling fan | 0 to 30 %. Too much cooling causes splitting between layers |
| Speed | 40 to 60 mm/s |
| Brim | 5 to 8 mm helps stop corners lifting |
| First layer | Slow and slightly squished |
- Nozzle
- ABS 240 to 255 °C, ASA 245 to 260 °C, HIPS 230 to 250 °C
- Bed
- 100 to 110 °C
- Cooling fan
- 0 to 30 %. Too much cooling causes splitting between layers
- Speed
- 40 to 60 mm/s
- Brim
- 5 to 8 mm helps stop corners lifting
- First layer
- Slow and slightly squished
Finishing and smoothing
ABS and ASA can be smoothed with acetone vapour in a sealed container, giving a glossy finish. Acetone is flammable and the vapour is harmful: work outdoors or with strong ventilation, keep ignition sources away and never leave the container unattended. HIPS dissolves in limonene, which is the usual way to remove supports from ABS prints.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Printing ABS without an enclosure and getting cracked, curled parts.
- Running a PTFE-lined hotend above its safe temperature.
- Putting the part fan on full.
- Printing in a closed room with no ventilation.
- Expecting ABS to stay yellow-free in sunlight; use ASA outdoors.
Frequently asked questions
ABS or ASA?
Use ASA for anything that sits outdoors or in sunlight. ABS is fine indoors and often cheaper.
Can I print ABS without an enclosure?
Small flat parts sometimes work, but tall or large parts warp. An enclosure is the single most useful upgrade.
What is HIPS used for?
Mainly as soluble support for ABS on dual-extruder printers, dissolved in limonene.
Is ABS safe to print at home?
Ventilate well. ABS and ASA release styrene vapour when printed, so do not print in a small closed room.
Why does ABS crack between layers?
Layers cooled too fast. Close the enclosure, reduce fan speed and print a little hotter.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



