How-to · Beginner · 3 min read
Filament Drying and Storage
Stop Wet Filament
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Most filaments absorb moisture from the air, which turns to steam in the nozzle and causes popping, stringing, bubbles and weak prints. Dry filament in a filament dryer or dehydrator at about 45 to 50 °C for PLA, 60 to 65 °C for PETG, 50 to 55 °C for TPU and 70 to 80 °C for nylon, for 4 to 12 hours. Then store it airtight with silica gel below about 20% humidity.
Key specs at a glance
- PLA
- 45 to 50 °C, 4 to 6 h
- PETG
- 60 to 65 °C, 4 to 6 h
- ABS / ASA
- 65 to 80 °C, 4 h
- TPU
- 50 to 55 °C, 4 to 8 h
- Nylon
- 70 to 80 °C, 8 to 12 h; print from a dry box
- Storage target
- Below about 20% RH, airtight, with silica gel and a hygrometer
Signs your filament is wet
- Popping or crackling sounds from the nozzle.
- Steam or wisps from the nozzle.
- More stringing than usual, and rough or fuzzy surfaces.
- Bubbles, gaps and weak, brittle parts.
- Brittle PLA that snaps in the tube (PLA gets brittle with age and moisture).
Nylon, TPU, PVA and PETG absorb water fastest; PLA more slowly. In humid weather, such as the Indian monsoon, an open spool can be noticeably wet within days.
How to dry it
- 1Check the spool: cardboard spools are fine up to about 60 °C; some plastic spools soften above that.
- 2Use a filament dryer, a food dehydrator, or a dryer box. Kitchen ovens are risky: their thermostats can overshoot by 10 to 20 °C and soften the filament.
- 3Dry at the temperature for the material (see Key specs) and keep it below the material's glass transition temperature.
- 4Print straight from the dryer or move the spool into airtight storage once it cools.
Storing filament
Use airtight boxes or vacuum bags with fresh silica gel, and keep a cheap hygrometer inside to check the humidity. Regenerate colour-changing silica gel in a warm oven when it changes colour. For nylon and TPU, print from a sealed dry box with a PTFE tube feeding the printer. Label each spool with the date opened and the material.
Try it: 3D print cost calculator
Change the values and the diagram and results update as you type.
Dry a wet spool of PETG
You need: Spool of PETG, Airtight box, Silica gel packets · Tools: Filament dryer or food dehydrator, Hygrometer
Get the parts2 of 3 found in our store · ₹785
Spool of PETGSUNLU PETG Red 1.75mm Filament 1kg Spool₹739- Airtight boxFind this part
Silica gel packetsThermal Conductive Silica Gel Pad – 10x10x6mm₹46Closest match, check the specs
- 1Check the spoolMake sure the spool material is safe at 65 °C.
- 2Load the dryerPlace the spool in the dryer and set it to 60 to 65 °C.
- 3DryRun for 4 to 6 hours, longer if it was very wet.
- 4TestPrint a small part; popping and stringing should be gone.
- 5StoreMove the spool to an airtight box with silica gel and a hygrometer.
Common mistakes to avoid
- Drying in a kitchen oven that overshoots and softens the filament.
- Drying above the plastic spool's softening point.
- Leaving nylon or TPU open to the air.
- Using silica gel that is already saturated.
- Drying filament once and then storing it open.
Frequently asked questions
How do I know if my filament is wet?
Popping sounds, steam, extra stringing, rough surfaces and weak parts are the usual signs.
Can I dry PLA in an oven?
Only if the oven can hold 45 to 50 °C accurately. Many ovens overshoot, so a dryer or dehydrator is safer.
Does PLA really absorb moisture?
Yes, more slowly than PETG or nylon, but in humid climates it will over weeks.
How long does dried filament stay dry?
Indefinitely in an airtight box with fresh silica gel; days to weeks if left open in humid air.
What humidity should I store filament at?
Below about 20% relative humidity for nylon and TPU, and below about 30 to 40% for PLA and PETG.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



