Component guide · Intermediate · 4 min read
AI-Thinker AiPi Boards

AiPi-SCP 2.4 Inch, AiPi-Eyes-S2 3.5 Inch, AiPi-DSL, AiPi-Eyes-DU Camera, AiPi-Audio, AiPi-Knob, VC-01 Offline Voice Kit and SiFli SF32LB525 Module
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
AI-Thinker's AiPi range uses the Bouffalo BL618 chip (RISC-V, Wi-Fi 6, BLE 5.3, Zigbee) with a screen, camera, audio codec or knob on a ready-made board. They suit smart panels, cameras and voice gadgets. The VC-01 kit recognises Chinese and English voice commands offline with no internet, and the SiFli SF32LB525 is a low-power Bluetooth module made for wearables with displays.
Key specs at a glance
- Chip
- Bouffalo BL618 (RISC-V 320 MHz, Wi-Fi 6, BLE 5.3, 802.15.4)
- Screens
- 1.28 to 3.5 inch LCD
- Camera
- On AiPi-Eyes-DU
- Audio
- ES8388 codec on AiPi-Audio
- Voice
- VC-01 offline keyword recognition, UART output
- Software
- Bouffalo SDK, AiPi examples, LVGL
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1AI-Thinker AiPi-SCP-2.4 AIoT Dev Board with 2.4-Inch RGB LCD₹1,159
Option 2AI-Thinker AiPi-Eyes-S2 Dev Board w/ 3.5-Inch Display₹2,380
Option 3AI-Thinker AiPi-DSL Dev Board w/ 2.4-Inch Display₹849
Option 4AI-Thinker AiPi-DSL 3.5-inch SPI Display Driver Board₹1,269
Option 5AI-Thinker AiPi-Eyes-DU BL618 AIoT Vision Dev Board w/ Camera₹569
Option 6AI-Thinker AiPi-Audio BL618 ES8388 Audio Dev Board₹979
What the AI-Thinker AiPi BL618 boards, VC-01 voice kit and SiFli SF32LB525 is
The AiPi boards are ready Ai-Thinker boards built on the Bouffalo BL618 chip, with a screen, camera, audio or knob already fitted for smart-home and voice gadgets.
These boards use the Bouffalo SDK rather than Arduino, so set up the toolchain from AI-Thinker's docs first. LVGL examples are included for the display boards.
The VC-01 sends a code over UART when it hears a trained command, so any Arduino or ESP32 can act on voice commands.
AI-Thinker AiPi BL618 boards, VC-01 voice kit and SiFli SF32LB525 pinout
The pins on the AI-Thinker AiPi BL618 boards, VC-01 voice kit and SiFli SF32LB525 and what each one does.
| Pin | Function |
|---|---|
| USB-C | Power, flashing and serial |
| Built-in screen | SPI, QSPI, 8080 parallel or RGB, already wired |
| Touch / buttons | Capacitive touch, buttons, encoder or keyboard depending on the board |
| Expansion | Qwiic/Grove, header pins or microSD |
| Battery | LiPo connector and charger on most |
- USB-C
- Power, flashing and serial
- Built-in screen
- SPI, QSPI, 8080 parallel or RGB, already wired
- Touch / buttons
- Capacitive touch, buttons, encoder or keyboard depending on the board
- Expansion
- Qwiic/Grove, header pins or microSD
- Battery
- LiPo connector and charger on most
Wiring the AI-Thinker AiPi BL618 boards, VC-01 voice kit and SiFli SF32LB525
These boards are complete; use the maker's pin definitions for the screen and touch. Never connect a 5V signal to the 3.3V GPIO.
| AI-Thinker AiPi BL618 boards, VC-01 voice kit and SiFli SF32LB525 pin | Connection | Note |
|---|---|---|
| USB-C | To a PC to flash | Hold BOOT if not detected |
| Battery | JST LiPo connector | Single cell 3.7V |
| Sensors | I2C or Grove port | 3.3V logic |
| VC-01 UART | TX to MCU RX, GND | Default 9600 baud |
- USB-C
- Connection:
- To a PC to flash
- Note:
- Hold BOOT if not detected
- Battery
- Connection:
- JST LiPo connector
- Note:
- Single cell 3.7V
- Sensors
- Connection:
- I2C or Grove port
- Note:
- 3.3V logic
- VC-01 UART
- Connection:
- TX to MCU RX, GND
- Note:
- Default 9600 baud
Example code
Command codes are set when you build the VC-01 firmware on AI-Thinker's online platform. Check the code table you generated.
#include <SoftwareSerial.h>
SoftwareSerial vc(2, 3); // RX, TX (VC-01 TX -> pin 2)
void setup() {
Serial.begin(115200);
vc.begin(9600);
pinMode(13, OUTPUT);
}
void loop() {
if (vc.available()) {
byte cmd = vc.read();
Serial.println(cmd, HEX);
if (cmd == 0x01) digitalWrite(13, HIGH); // e.g. "turn on the light"
if (cmd == 0x02) digitalWrite(13, LOW); // e.g. "turn off the light"
}
}Setup and tuning
install the Bouffalo SDK and the AiPi example repository; build and flash over USB with the provided tools.
each board has demos for its screen, camera or audio. Run one before changing the code.
use a good USB-C cable and a 5 V supply of at least 1 A for screen and camera boards.
use LVGL for screen boards; the examples already set up the display driver and touch.
the VC-01 sends a code over UART for each recognised phrase, so any board can act on it.
What you need
Shop this list10 of 11 found in our store · ₹11,471
AI-Thinker AiPi-SCP-2.4 AIoT Dev Board with 2.4-Inch RGB LCD: the part this guide coversAI-Thinker AiPi-SCP-2.4 AIoT Dev Board with 2.4-Inch RGB LCD₹1,159
AI-Thinker AiPi-Eyes-S2 Dev Board w/ 3.5-Inch Display: another version this guide coversAI-Thinker AiPi-Eyes-S2 Dev Board w/ 3.5-Inch Display₹2,380
AI-Thinker AiPi-DSL Dev Board w/ 2.4-Inch Display: another version this guide coversAI-Thinker AiPi-DSL Dev Board w/ 2.4-Inch Display₹849
AI-Thinker AiPi-DSL 3.5-inch SPI Display Driver Board: another version this guide coversAI-Thinker AiPi-DSL 3.5-inch SPI Display Driver Board₹1,269
AI-Thinker AiPi-Eyes-DU BL618 AIoT Vision Dev Board w/ Camera: another version this guide coversAI-Thinker AiPi-Eyes-DU BL618 AIoT Vision Dev Board w/ Camera₹569
AI-Thinker AiPi-Audio BL618 ES8388 Audio Dev Board: another version this guide coversAI-Thinker AiPi-Audio BL618 ES8388 Audio Dev Board₹979
AI-Thinker AiPi-Knob V1.0 Rotary Encoder Board w/ 1.28-Inch Display: another version this guide coversAI-Thinker AiPi-Knob V1.0 Rotary Encoder Board w/ 1.28-Inch Display₹1,499
AI-Thinker VC-01-Kit Offline Speech Recognition Module: another version this guide coversAI-Thinker VC-01-Kit Offline Speech Recognition Module₹859
SiFli Technologies SF32LB525 Bluetooth 5.3 AIoT Module N16R8 w/ QSPI Display: another version this guide coversSiFli Technologies SF32LB525 Bluetooth 5.3 AIoT Module N16R8 w/ QSPI Display₹849
USB-C cable: for power, flashing and the serial monitorArduino USB-C to USB-C Cable w/ USB-A Adapter₹1,059Closest match, check the specs- Uno R3 development board: the controller used in the wiring tableFind this part
Alternatives and when to choose them
- AI-Thinker BL602 modules: smaller modules.
- Small ESP32-S3 display boards: Arduino friendly.
- RISC-V boards: other RISC-V boards.
Common mistakes to avoid
- Expecting ESP32 Arduino libraries to work on BL618.
- Using a weak USB cable, so the screen flickers or the board resets.
- Writing a UI from scratch instead of starting from the LVGL example.
- Expecting the voice module to learn any new phrase without setup.
Frequently asked questions
Can I program AiPi boards in the Arduino IDE?
Not officially. They use the Bouffalo SDK in C, with LVGL for the screens.
Does the VC-01 voice module need internet?
No. It recognises its preset Chinese and English keywords offline and sends a serial code.
What is special about the BL618 chip?
It combines a 320 MHz RISC-V core with Wi-Fi 6, BLE 5.3 and 802.15.4 for Zigbee and Thread.
Can the AiPi boards run Home Assistant?
No, but they can act as panels or sensors that talk to Home Assistant over Wi-Fi or MQTT.
Which board should I start with?
The 2.4 inch AiPi-SCP is a simple screen board, and the AiPi-Eyes boards add a camera.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


