Component guide · Beginner · 4 min read
Arduino Nano Family

Nano 33 BLE and BLE Rev2, Nano 33 BLE Sense Rev2, Nano 33 IoT, Nano Every (ATmega4809), Nano Matter and Nano R4, with and without Headers
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
All these boards share the small Nano footprint but differ inside. Nano Every is the 5 V upgrade of the classic Nano. Nano 33 BLE and BLE Sense run on nRF52840 at 3.3 V, and the Sense adds motion, sound, light and environment sensors for TinyML. Nano 33 IoT adds Wi-Fi. Nano Matter runs Matter and Thread for smart homes, and Nano R4 brings the UNO R4 chip to the Nano size.
Key specs at a glance
- Nano Every
- ATmega4809, 5 V logic
- Nano 33 BLE / Sense Rev2
- nRF52840, BLE 5, 3.3 V; Sense adds IMU, mic, light, temp, humidity, pressure
- Nano 33 IoT
- SAMD21 + u-blox NINA Wi-Fi/BLE, 3.3 V
- Nano Matter
- Silicon Labs MGM240S, Matter over Thread, BLE
- Nano R4
- Renesas RA4M1, 5 V, Qwiic
- Headers
- Sold with or without soldered headers
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Arduino Nano 33 BLE Board (Without Headers)₹1,962
Option 2Arduino Nano 33 BLE Rev2 Development Board₹1,989
Option 3Arduino Nano 33 BLE Rev2 Development Board with Headers₹2,459
Option 4Arduino Nano 33 BLE Sense Rev2 ABX00069₹3,949
Option 5Arduino Nano 33 BLE Sense w/ Headers – Rev 2 (ABX00070)₹4,049
Option 6Arduino Nano 33 IoT Development Board ABX00027₹2,439
What the Arduino Nano family: Nano 33 BLE, BLE Sense Rev2, Nano 33 IoT, Nano Every, Nano Matter and Nano R4 is
The Nano family shares one small footprint, but the boards inside differ: 5 V AVR and Renesas chips, 3.3 V nRF52840 and SAMD21 chips, and Matter radios.
Check the logic voltage before wiring: Nano 33 boards and Nano Matter are 3.3 V only and are damaged by 5 V signals, while Nano Every and Nano R4 work at 5 V. Install the right core in Boards Manager (Mbed OS Nano for 33 BLE, SAMD for 33 IoT, megaAVR for Every, Silicon Labs for Matter, UNO R4 for Nano R4).
If an nRF52840 Nano stops being detected, double-tap reset to enter the bootloader and upload again. The pinout matches the classic Nano, but shields made for 5 V Nanos need level shifting on the 3.3 V boards.
Arduino Nano family: Nano 33 BLE, BLE Sense Rev2, Nano 33 IoT, Nano Every, Nano Matter and Nano R4 pinout
The pins on the Arduino Nano family: Nano 33 BLE, BLE Sense Rev2, Nano 33 IoT, Nano Every, Nano Matter and Nano R4 and what each one does.
| Pin | Function |
|---|---|
| D2-D13 | Digital I/O |
| A0-A7 | Analog inputs |
| 3V3 | 3.3 V output |
| VIN | External supply input |
| SDA / SCL | A4 / A5 I2C |
| Micro USB / USB-C | Power and programming |
- D2-D13
- Digital I/O
- A0-A7
- Analog inputs
- 3V3
- 3.3 V output
- VIN
- External supply input
- SDA / SCL
- A4 / A5 I2C
- Micro USB / USB-C
- Power and programming
Wiring the Arduino Nano family: Nano 33 BLE, BLE Sense Rev2, Nano 33 IoT, Nano Every, Nano Matter and Nano R4
Nano 33 boards cut the 5 V pin by default; it needs a solder bridge to output 5 V from USB.
| Arduino Nano family: Nano 33 BLE, BLE Sense Rev2, Nano 33 IoT, Nano Every, Nano Matter and Nano R4 pin | Connection | Note |
|---|---|---|
| USB | PC | Install the matching core |
| Sensors | 3.3 V on Nano 33 and Matter | Level shift 5 V parts |
| 5 V sensors | Nano Every or Nano R4 | Direct |
- USB
- Connection:
- PC
- Note:
- Install the matching core
- Sensors
- Connection:
- 3.3 V on Nano 33 and Matter
- Note:
- Level shift 5 V parts
- 5 V sensors
- Connection:
- Nano Every or Nano R4
- Note:
- Direct
Example code
Rev2 uses the BMI270/BMM150 IMU; the original Sense uses LSM9DS1 with the Arduino_LSM9DS1 library.
#include <Arduino_BMI270_BMM150.h>
void setup() {
Serial.begin(115200);
while (!Serial);
if (!IMU.begin()) {
Serial.println("IMU not found");
while (1);
}
}
void loop() {
float x, y, z;
if (IMU.accelerationAvailable()) {
IMU.readAcceleration(x, y, z);
Serial.print(x); Serial.print('\t');
Serial.print(y); Serial.print('\t');
Serial.println(z);
}
delay(100);
}Setup and tuning
the Nano Every and Nano R4 are 5 V; Nano 33 boards and Nano Matter are 3.3 V only.
install the matching core (megaAVR, Mbed nRF52840, SAMD, Renesas or Silicon Labs) before uploading.
on Nano 33 boards, the 5 V pin is disabled by default; bridge the VUSB jumper if a part needs USB 5 V.
double-tap reset if a Nano 33 board does not show a port.
use the Arduino libraries for the onboard IMU, microphone and environment sensors.
What you need
Shop this list12 of 12 found in our store · ₹27,295
Arduino Nano 33 BLE Board (Without Headers): the part this guide coversArduino Nano 33 BLE Board (Without Headers)₹1,962
Arduino Nano 33 BLE Rev2 Development Board: another version this guide coversArduino Nano 33 BLE Rev2 Development Board₹1,989
Arduino Nano 33 BLE Rev2 Development Board with Headers: another version this guide coversArduino Nano 33 BLE Rev2 Development Board₹1,989
Arduino Nano 33 BLE Sense Rev2 ABX00069: another version this guide coversArduino Nano 33 BLE Sense Rev2 ABX00069₹3,949
Arduino Nano 33 BLE Sense w/ Headers – Rev 2 (ABX00070): another version this guide coversArduino Nano 33 BLE Sense w/ Headers – Rev 2 (ABX00070)₹4,049
Arduino Nano 33 IoT Development Board ABX00027: another version this guide coversArduino Nano 33 IoT Development Board ABX00027₹2,439
Arduino Nano 33 IoT with Headers – WiFi/BLE SAMD21: another version this guide coversArduino Nano 33 IoT with Headers – WiFi/BLE SAMD21₹2,609
Arduino Nano Every ABX00028 (5V, ATMega4809): another version this guide coversArduino Nano Every ABX00028 (5V, ATMega4809)₹1,179
Arduino Nano Every with Headers (ATMEGA4809): another version this guide coversArduino Nano Every with Headers (ATMEGA4809)₹1,519
Arduino Nano Matter Dev Board ABX00112: another version this guide coversArduino Nano Matter Dev Board ABX00112₹2,029
Arduino Nano Matter with Headers ABX00137: another version this guide coversArduino Nano Matter with Headers ABX00137₹2,353
Arduino Nano R4 ABX00142 w/ Headers: another version this guide coversArduino Nano R4 ABX00142 w/ Headers₹1,229
Alternatives and when to choose them
- Arduino Nano: the classic ATmega328P Nano.
- Official Arduino boards compared: every board side by side.
- nRF52 BLE boards: other nRF52840 boards.
Common mistakes to avoid
- Connecting 5 V signals to a 3.3 V Nano 33 board.
- Selecting the classic Nano board type for a Nano Every.
- Expecting 5 V on the 5 V pin of a Nano 33 board by default.
- Mixing up Nano 33 IoT (Wi-Fi) and Nano 33 BLE (no Wi-Fi).
Frequently asked questions
Is the Nano 33 BLE 5 V tolerant?
No. Its pins are 3.3 V only, so use level shifters with 5 V parts.
Which Nano should replace my old Nano?
The Nano Every or Nano R4 keeps 5 V logic and the same footprint, so most old projects move easily.
What is the Nano 33 BLE Sense used for?
It suits TinyML and sensing projects, with an IMU, microphone and environment sensors on board.
What is the Nano Matter for?
It connects to smart-home systems that support Matter over Thread, such as recent Google, Apple and Amazon hubs.
Why is there no 5 V on my Nano 33 board?
The 5 V pin is linked to USB through a jumper that ships open; bridge the VUSB pads to enable it.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
