Buying guide · Intermediate · 3 min read
Audio Amplifier Boards
TPA3116, LM386, PAM8610 and More
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
An amplifier board makes a small audio signal strong enough to drive speakers. Class D boards such as the TPA3116 and PAM8610 are efficient and run cool, while class AB boards such as the TDA7297 are simpler but get hot. The LM386 suits tiny speakers and headphone projects. Match the board to your speaker impedance and supply voltage, and expect real power well below headline numbers unless the supply can deliver it.
Key specs at a glance
- LM386
- About 0.3 to 1 W, 4 to 12 V, mono, simple
- PAM8403 / PAM8610
- 3 W x 2 at 5 V / about 10 W x 2 at 12 V, class D
- TPA3116D2
- Up to about 2 x 50 W at 24 V into 4 Ω (at high distortion), 12 to 24 V
- TDA7297
- Class AB 2 x 15 W, needs a heatsink
- Speaker load
- 4 Ω or 8 Ω as specified; never below the minimum
- Output
- Many class D boards use bridge-tied load (BTL): never ground a speaker wire
Which board to use
| Board | Supply | Power | Good for |
|---|---|---|---|
| LM386 | 4 to 12 V | Under 1 W | Small speakers, intercoms, test projects |
| PAM8403 | 5 V | 2 x 3 W | USB-powered speakers, see the PAM8403 guide |
| PAM8610 | 7 to 15 V | 2 x 10 W | Desk speakers |
| TPA3116D2 | 12 to 24 V | 2 x 30 to 50 W | Bookshelf speakers, Bluetooth boomboxes |
| TDA7297 | 9 to 18 V | 2 x 15 W | Simple car-style builds with a heatsink |
- LM386
- Supply:
- 4 to 12 V
- Power:
- Under 1 W
- Good for:
- Small speakers, intercoms, test projects
- PAM8403
- Supply:
- 5 V
- Power:
- 2 x 3 W
- Good for:
- USB-powered speakers, see the PAM8403 guide
- PAM8610
- Supply:
- 7 to 15 V
- Power:
- 2 x 10 W
- Good for:
- Desk speakers
- TPA3116D2
- Supply:
- 12 to 24 V
- Power:
- 2 x 30 to 50 W
- Good for:
- Bookshelf speakers, Bluetooth boomboxes
- TDA7297
- Supply:
- 9 to 18 V
- Power:
- 2 x 15 W
- Good for:
- Simple car-style builds with a heatsink
Supply and real watts
Headline ratings are usually measured at 10 % distortion, which sounds harsh. Plan on about 70 % of that for clean sound. Power depends on supply voltage and speaker impedance: a TPA3116 at 12 V cannot produce its 24 V figure.
Size the supply for the average music power, not the peak; a 24 V 4 A supply is plenty for a stereo TPA3116 at home listening levels. A cheap switching supply can add noise, so use a decent SMPS and add a large capacitor at the board if needed.
Hum, hiss and wiring
- Connect the audio ground, power ground and source ground at one point to avoid ground loops.
- A buzzing hum when a USB-powered source is connected usually means a ground loop; a ground loop isolator helps.
- Class D outputs on BTL boards are floating: each speaker connects only to its own two terminals, and neither may go to ground or be shared.
- Keep input wires short and use shielded cable.
- Add a potentiometer volume control at the input, and match the source level so the input is not overdriven.
- Speakers must handle the power; see speakers.
Try it: dB converter calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Grounding one speaker wire on a BTL class D board.
- Using a 2 Ω speaker on a board rated for 4 Ω minimum.
- Expecting headline watts from a low-voltage supply.
- Running a class AB board without a heatsink.
- Ground loops from multiple USB supplies.
Frequently asked questions
Which amplifier for a Bluetooth speaker?
A PAM8403 for small 5 V builds or a TPA3116 for larger 12 to 24 V builds.
Can I connect one speaker wire to ground?
Not on bridge-tied class D boards; each output pair must stay separate.
Why does my amplifier hum?
Usually a ground loop or noisy supply. Use one ground point and shielded inputs.
Is class D good quality?
Modern class D chips sound very good and are far more efficient than class AB.
What supply does a TPA3116 need?
12 to 24 V; 24 V gives the most power. Current depends on volume and speakers.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




