How-to · Beginner · 3 min read
BLE Beacons
iBeacon, Eddystone, Asset Tags and Proximity Projects
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A BLE beacon is a small battery-powered transmitter that repeatedly broadcasts an ID. A phone or ESP32 scans for it and uses the ID and signal strength to know which beacon is near. Set the UUID, major and minor values, TX power and advertising interval with the vendor app. Shorter intervals and higher power improve response but drain the battery faster.
Key specs at a glance
- Formats
- iBeacon, Eddystone, custom advertising
- Chips
- nRF52810/nRF52832 on common beacons
- Battery
- CR2032 or CR2477; months to years
- Interval
- 100 ms to several seconds
- Extras
- Accelerometer, temperature and button on some tags
- Housing
- PCB beacons or IP67 tags
How a beacon works
A beacon sends a short advertising packet many times a second. Your app reads the packet and the signal strength. It does not connect to the beacon. Because it only broadcasts, a beacon uses very little power, so a coin cell can run it for a year or more depending on the interval; see BLE modules for the radio basics.
iBeacon identifiers
An iBeacon packet carries a UUID (identifies your organisation or project), a major number (a group, such as a floor) and a minor number (the individual beacon). Pick values and record them in a table. Keep the UUID the same across beacons from one deployment and change major/minor for each location.
| Setting | Effect | Advice |
|---|---|---|
| Advertising interval | How often it broadcasts | 300 to 1000 ms is a good balance |
| TX power | Range | Lower power for room-level, higher for halls |
| UUID / major / minor | Identity | Plan before you deploy |
| Motion trigger | Wake on movement | Saves battery for asset tags |
- Advertising interval
- Effect:
- How often it broadcasts
- Advice:
- 300 to 1000 ms is a good balance
- TX power
- Effect:
- Range
- Advice:
- Lower power for room-level, higher for halls
- UUID / major / minor
- Effect:
- Identity
- Advice:
- Plan before you deploy
- Motion trigger
- Effect:
- Wake on movement
- Advice:
- Saves battery for asset tags
Distance from RSSI
Signal strength falls with distance, but walls, bodies and reflections change it a lot. Use RSSI for near, far and room-level zones rather than exact metres. Average several readings. For accurate positioning use UWB; see UWB modules.
Scanning with an ESP32
1. Use the Arduino BLE library to start a scan. 2. Filter packets by manufacturer data (the iBeacon header) or address. 3. Read the UUID, major, minor and RSSI. 4. Act: open a door, log a visit or send to MQTT; see MQTT. For classic smartphones, use the beacon scanning API of your platform.
Uses
Museum and shop proximity messages, asset tracking in a workshop, attendance and room presence, finding keys or tools and low-power sensor broadcasts. For longer range sensor networks see LoRaWAN.
Try it: Battery life calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Expecting metre-accurate distance from RSSI.
- Using the same major/minor for every beacon.
- Setting a very short interval and draining the battery.
- Putting a beacon inside a metal box.
- Not updating firmware when the vendor app offers it.
Frequently asked questions
Does a beacon connect to my phone?
No. It only broadcasts; the phone listens.
How long does the battery last?
From months to years depending on interval and power.
What is the difference between iBeacon and Eddystone?
They are different packet formats; both use BLE advertising.
Can I scan with an ESP32?
Yes, with the BLE library.
Is RSSI accurate?
Only roughly. It varies with obstacles.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






