How-to · Advanced · 3 min read
UWB Modules
DW3000 Indoor Positioning with Anchors and Tags
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
UWB measures the time radio pulses take to travel, so it can find distance to within centimetres, much better than Bluetooth signal strength. With one tag and at least three anchors at known positions you can calculate 2D location; four give 3D. Use DW3000-based boards, calibrate antenna delay, mount anchors high with a clear view and check local radio rules.
Key specs at a glance
- Chip
- Qorvo DW3000 / DW3210
- Accuracy
- About 10 to 30 cm in good conditions
- Methods
- Two-way ranging (TWR) and TDoA
- Dev boards
- AI-Thinker BU03, BU04, ESP32-DW3210 boards
- Range
- Tens of metres line of sight
- Also in this category
- 24 GHz radar modules (Rd-03E, RD-01)
How UWB positioning works
A tag exchanges messages with each anchor (two-way ranging) and calculates the distance from the round-trip time. With three or more anchor distances, the position is found by trilateration. Fixed anchors need accurately measured coordinates; their placement decides the accuracy.
UWB compared with other methods
Pick by accuracy needed.
| Technology | Accuracy | Notes |
|---|---|---|
| UWB | 10 to 30 cm | Needs anchors; line of sight helps |
| BLE RSSI | 1 to 5 m | Simple and cheap; see BLE beacons |
| Wi-Fi RTT | 1 to 2 m | Needs compatible access points |
| GNSS | Metres outdoors | Does not work indoors; see GNSS modules |
- UWB
- Accuracy:
- 10 to 30 cm
- Notes:
- Needs anchors; line of sight helps
- BLE RSSI
- Accuracy:
- 1 to 5 m
- Notes:
- Simple and cheap; see BLE beacons
- Wi-Fi RTT
- Accuracy:
- 1 to 2 m
- Notes:
- Needs compatible access points
- GNSS
- Accuracy:
- Metres outdoors
- Notes:
- Does not work indoors; see GNSS modules
Setting up anchors and tags
- 1Place at least three anchors high on walls or poles, spread around the area, and measure their coordinates.
- 2Flash anchor and tag firmware on the dev boards.
- 3Calibrate antenna delay for each device so distances are correct.
- 4Run ranging and compare the measured distance with a tape measure.
- 5Send the distances to a positioning solver on a PC or microcontroller.
- 6Filter the result with a Kalman or moving-average filter.
Boards
AI-Thinker BU03 and BU04 kits and the ESP32-DW3210 evaluation board provide UWB with a microcontroller on board. The DW3210 board has a dual-antenna switch for angle-of-arrival experiments. Many include UART AT commands to get started. For wiring and serial use see UART.
Limits and rules
Metal, bodies and walls block or reflect UWB, creating errors. Add anchors to cover dead zones. Radio rules for UWB differ by country; check what you may use. Robots can combine UWB with encoders and IMUs for smooth tracking.
Try it: Frequency wavelength calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Placing anchors at nearly the same height and in a line.
- Skipping antenna delay calibration.
- Expecting good readings through walls.
- Using inaccurate anchor coordinates.
- Ignoring local radio regulations.
Frequently asked questions
How accurate is UWB?
Typically 10 to 30 cm in good conditions.
How many anchors do I need?
Three for 2D, four for 3D.
Is UWB the same as Bluetooth?
No. It uses very short pulses over a wide band and measures time of flight.
Can I use UWB outdoors?
Yes with a clear view, but check local rules.
Which boards can I start with?
DW3000 kits like the AI-Thinker BU03/BU04.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






