Component guide · Advanced · 3 min read
Catalytic Combustible Gas Sensors

Winsen MC105, MC109, MC115, MC119), CMV-2021D Hydrogen, GM402B MEMS and SGX MP-7227
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Catalytic (pellistor) sensors measure flammable gas as a percentage of its lower explosive limit (LEL). Gas burns on a heated bead and raises its resistance, which a Wheatstone bridge with a matching reference bead turns into a few millivolts. The Winsen MC series are pellistor pairs, the CMV-2021D is a MEMS catalytic hydrogen sensor, and the SGX MP-7227 is a ready methane module with RS232 output.
Key specs at a glance
- Principle
- Catalytic bead (pellistor) in a bridge
- Range
- 0 to 100% LEL methane, LPG, hydrogen and others
- Bridge supply
- About 2.5 to 3 V at 100 to 200 mA (MC series)
- Output
- About 15 to 60 mV at 1% vol methane
- Response
- T90 under 10 to 20 s
- Linear
- Yes, unlike metal-oxide sensors
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Winsen MC105 Catalytic Flame Gas Sensor Module – Plastic Encapsulation₹249
Option 2Winsen MC109 Catalytic Flammable Gas Sensor – Metal Mesh Encapsulation₹1,609
Option 3Winsen MC115 Catalytic Combustible Gas Sensor Pair Module₹1,109
Option 4Winsen MC119 Catalytic Flammable Gas Sensor Module – Metal Mesh Encapsulation₹2,659
Option 5Winsen CMV-2021D MEMS Catalytic Hydrogen Sensor – 3.0V DC₹3,449
Option 6Winsen GM402B MEMS Combustible Gas Sensor Module – Ceramic Encapsulation₹459
What the Catalytic and MEMS combustible gas sensors is
Catalytic (pellistor) sensors detect flammable gases such as methane, LPG and hydrogen by burning them on a heated bead and measuring the change in a bridge circuit.
The detector and compensator beads form two arms of the bridge; two fixed resistors and a zero trimmer form the others. The bridge output goes to an amplifier or an ADS1115 in differential mode.
Silicones, sulphur and lead compounds poison the beads. Keep them away from sealants and test with clean calibration gas.
Catalytic and MEMS combustible gas sensors pinout
The pins on the Catalytic and MEMS combustible gas sensors and what each one does.
| Pin | Function |
|---|---|
| D (detector) | Bridge arm |
| C (compensator) | Bridge arm |
| Common | Bridge supply |
| Modules | VCC, GND, TX (MP-7227) |
- D (detector)
- Bridge arm
- C (compensator)
- Bridge arm
- Common
- Bridge supply
- Modules
- VCC, GND, TX (MP-7227)
Wiring the Catalytic and MEMS combustible gas sensors
Pellistors draw over 100 mA. Use a separate regulator, not a microcontroller pin.
| Catalytic and MEMS combustible gas sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| Bridge supply | Regulated 3 V | Regulated 3 V |
| Bridge output + | ADS1115 A0 | ADS1115 A0 |
| Bridge output - | ADS1115 A1 | ADS1115 A1 |
| ADS1115 SDA / SCL | A4 / A5 | GPIO 21 / 22 |
- Bridge supply
- Arduino Uno:
- Regulated 3 V
- ESP32:
- Regulated 3 V
- Bridge output +
- Arduino Uno:
- ADS1115 A0
- ESP32:
- ADS1115 A0
- Bridge output -
- Arduino Uno:
- ADS1115 A1
- ESP32:
- ADS1115 A1
- ADS1115 SDA / SCL
- Arduino Uno:
- A4 / A5
- ESP32:
- GPIO 21 / 22
Example code
A minimal sketch to check the part works.
#include <Adafruit_ADS1X15.h>
Adafruit_ADS1115 ads;
float zeroMv;
const float MV_PER_LEL = 0.5; // from your calibration gas
float mv() { return ads.computeVolts(ads.readADC_Differential_0_1()) * 1000.0; }
void setup() {
Serial.begin(115200);
ads.begin(); ads.setGain(GAIN_SIXTEEN);
delay(60000); // warm-up in clean air
zeroMv = mv();
}
void loop() {
float lel = (mv() - zeroMv) / MV_PER_LEL;
Serial.print(lel, 1); Serial.println(" % LEL");
delay(1000);
}Setup and tuning
wire the detector and reference beads in a Wheatstone bridge with a balance pot.
feed the bridge from a stable 2.5 to 3 V source that can supply 100 to 200 mA.
use an instrumentation amplifier, as the output is only tens of millivolts.
warm up for several minutes in clean air, then set the zero.
use a known concentration to set the span.
What you need
Shop this list11 of 12 found in our store · ₹13,928
Winsen MC105 Catalytic Flame Gas Sensor Module – Plastic Encapsulation: the part this guide coversWinsen MC105 Catalytic Flame Gas Sensor Module – Plastic Encapsulation₹249
Winsen MC109 Catalytic Flammable Gas Sensor – Metal Mesh Encapsulation: another version this guide coversWinsen MC109 Catalytic Flammable Gas Sensor – Metal Mesh Encapsulation₹1,609
Winsen MC115 Catalytic Combustible Gas Sensor Pair Module: another version this guide coversWinsen MC115 Catalytic Combustible Gas Sensor Pair Module₹1,109
Winsen MC119 Catalytic Flammable Gas Sensor Module – Metal Mesh Encapsulation: another version this guide coversWinsen MC119 Catalytic Flammable Gas Sensor Module – Metal Mesh Encapsulation₹2,659
Winsen CMV-2021D MEMS Catalytic Hydrogen Sensor – 3.0V DC: another version this guide coversWinsen CMV-2021D MEMS Catalytic Hydrogen Sensor – 3.0V DC₹3,449
Winsen GM402B MEMS Combustible Gas Sensor Module – Ceramic Encapsulation: another version this guide coversWinsen GM402B MEMS Combustible Gas Sensor Module – Ceramic Encapsulation₹459
Amphenol SGX Sensortech Sensortech MP-7227 Methane Gas Sensor Module – RS232 Interface, Audible Alarm: another version this guide coversAmphenol SGX Sensortech MP-7227 Methane Gas Sensor Module – RS232 Interface, Audible Alarm₹3,602
ADS1115 16-bit 4-channel ADC module: to read small sensor voltages accuratelyADS1115 16-Bit 4-Channel ADC Module₹199
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Buzzer module 3.3-5 V: for an audible alarmBuzzer Module 3.3–5V₹27
Alternatives and when to choose them
- Figaro TGS sensors: metal-oxide alarm sensors.
- MQ-6 and MQ-8: cheap LPG and hydrogen.
- RS485 gas transmitters: ready industrial units.
Common mistakes to avoid
- Powering the bridge from a weak or noisy supply.
- Reading the millivolt output without amplification.
- Using it near silicone sprays that poison the bead.
- Relying on a homemade detector as a life-safety alarm.
Frequently asked questions
What does % LEL mean?
It is the percentage of the lower explosive limit, the lowest concentration that can burn.
Can a catalytic sensor work in low oxygen?
No. The bead needs oxygen to burn the gas, so readings fail in low-oxygen air.
What can poison the sensor?
Silicone vapours, lead and sulphur compounds can permanently reduce its sensitivity.
Can I read it with an Arduino?
Yes, through a bridge and amplifier into an analog input or an ADS1115.
Is this suitable for a certified gas alarm?
A DIY build is for learning; safety alarms must use certified detectors.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

