Component guide · Advanced · 4 min read
Compute Module 5 Carrier Boards

Official CM5 IO Board and Case, CM5 to Pi 5 Adapter, Waveshare Nano, Mini, Dual Ethernet and Industrial IoT Bases
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Carrier boards turn a Compute Module 5 into a working computer. The official CM5 IO board and case give full ports plus an M.2 slot. The CM5 to Pi 5 adapter fits Pi 5 cases and HATs. Waveshare Nano and Mini bases are small enough for products, the dual Ethernet base suits routers, and the industrial IoT board adds 4G or 5G, LoRa and wide-voltage power.
Key specs at a glance
- Module
- CM5 (most also accept CM4)
- PCIe
- M.2 M key on IO board and several bases
- Network
- 1 or 2 Gigabit ports
- Video
- 2 x HDMI on full boards, 1 on Nano
- Power
- 5V 5A USB-C or wide DC on industrial
- Case
- Official IO case with fan
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Raspberry Pi Compute Module 5 IO Board₹3,159
Option 2Raspberry Pi Compute Module 5 IO Case₹1,924
Option 3Waveshare CM5 to Pi 5 Adapter Board₹2,799
Option 4Waveshare Nano Base Board (B) for Raspberry Pi CM5₹2,369
Option 5Waveshare CM5 Nano Base Board (A) for Raspberry Pi CM5₹3,579
Option 6Waveshare Mini Base Board (A) for Raspberry Pi CM5₹1,889
What the Compute Module 5 carrier boards is
Compute Module 5 carrier boards hold the Raspberry Pi CM5 and break out its ports, giving Pi 5 performance in a product-ready form.
The CM5 uses the same connectors as the CM4, so most CM4 carriers accept it, but CM5 needs more power (5V 5A) and its USB 3.0 ports only work on carriers wired for them.
The official IO case holds the IO board, a fan and an antenna, making a tidy desktop or kiosk unit.
Compute Module 5 carrier boards pinout
The pins on the Compute Module 5 carrier boards and what each one does.
| Pin | Function |
|---|---|
| 2 x 100-pin connectors | Hold the Compute Module and carry PCIe, USB, Ethernet, HDMI, CSI, DSI and GPIO |
| nRPIBOOT / BOOT switch | Puts an eMMC module into USB flashing mode |
| Power input | USB-C 5V or 7 to 36V DC on industrial boards |
| 40-pin header | Standard HAT GPIO on most carriers |
- 2 x 100-pin connectors
- Hold the Compute Module and carry PCIe, USB, Ethernet, HDMI, CSI, DSI and GPIO
- nRPIBOOT / BOOT switch
- Puts an eMMC module into USB flashing mode
- Power input
- USB-C 5V or 7 to 36V DC on industrial boards
- 40-pin header
- Standard HAT GPIO on most carriers
Wiring the Compute Module 5 carrier boards
Line the module up with both connectors and press straight down on the centre; never rock it. Lite modules (no eMMC) boot from the carrier's microSD slot instead.
| Compute Module 5 carrier boards pin | Step | Note |
|---|---|---|
| Module | Press both connectors down evenly | Fit the heatsink after |
| Flashing (eMMC) | BOOT switch on, USB to a PC, run rpiboot | Then Raspberry Pi Imager |
| Power | Carrier input, not the module | Check the voltage range |
- Module
- Step:
- Press both connectors down evenly
- Note:
- Fit the heatsink after
- Flashing (eMMC)
- Step:
- BOOT switch on, USB to a PC, run rpiboot
- Note:
- Then Raspberry Pi Imager
- Power
- Step:
- Carrier input, not the module
- Note:
- Check the voltage range
Example code
On a CM5 carrier with an M.2 slot, follow the Pi 5 NVMe steps: update the bootloader and set BOOT_ORDER to boot from NVMe.
# On Linux or Raspberry Pi OS (Windows: use the rpiboot installer)
sudo apt install git libusb-1.0-0-dev pkg-config build-essential
git clone --depth=1 https://github.com/raspberrypi/usbboot
cd usbboot && make
# Set the carrier's BOOT switch / jumper, connect its USB port, power on
sudo ./rpiboot -d mass-storage-gadget64
# The eMMC now appears as a USB drive: write it with Raspberry Pi ImagerSetup and tuning
use a 5 V 5 A or higher supply as the carrier specifies; CM5 with NVMe draws more.
use rpiboot with the boot jumper for eMMC models, then Raspberry Pi Imager.
fit the official cooler or a heatsink, because the CM5 runs hotter than the CM4.
connect NVMe drives in the M.2 slot and enable PCIe in config.txt if needed.
use it to test CM5 builds in Pi 5 cases and accessories.
What you need
Shop this list12 of 12 found in our store · ₹42,557
Raspberry Pi Compute Module 5 IO Board: the part this guide coversRaspberry Pi Compute Module 5 IO Board₹3,159
Raspberry Pi Compute Module 5 IO Case: another version this guide coversRaspberry Pi Compute Module 5 IO Case₹1,924
Waveshare CM5 to Pi 5 Adapter Board: another version this guide coversWaveshare CM5 to Pi 5 Adapter Board₹2,799
Waveshare Nano Base Board (B) for Raspberry Pi CM5: another version this guide coversWaveshare Nano Base Board (B) for Raspberry Pi CM5₹2,369
Waveshare CM5 Nano Base Board (A) for Raspberry Pi CM5: another version this guide coversWaveshare CM5 Nano Base Board (A) for Raspberry Pi CM5₹3,579
Waveshare Mini Base Board (A) for Raspberry Pi CM5: another version this guide coversWaveshare Mini Base Board (A) for Raspberry Pi CM5₹1,889
Waveshare CM5 Dual GbE Mini Base Board: another version this guide coversWaveshare CM5 Dual GbE Mini Base Board₹2,619
Waveshare Dual Ethernet Base Board for Raspberry Pi CM5: another version this guide coversWaveshare Dual Ethernet Base Board for Raspberry Pi CM5₹5,770
Waveshare CM5 Industrial IoT 4G/5G/LoRa GbE 4K HDMI Board: another version this guide coversWaveshare CM5 Industrial IoT 4G/5G/LoRa GbE 4K HDMI Board₹6,609
Raspberry Pi Compute Module 5 (8 GB, 32 GB eMMC, Wi-Fi): the module the carrier holdsRaspberry Pi Compute Module 5 IO Board₹3,159Closest match, check the specs
Official 27W USB-C power supply for Pi 5: for CM5 and Pi 5 buildsOfficial 27W USB-C PD Power Supply for Raspberry Pi 5 – IN Plug₹1,319
WD Green SN350 NVMe SSD: for carriers with an M.2 slotWD Green SN350 NVMe SSD₹7,362
Alternatives and when to choose them
- CM4 carrier boards: more choices.
- Compute Modules: CM4 vs CM5.
- Pi 5 NVMe HATs: the same SSD on a Pi 5.
Common mistakes to avoid
- Using a weak supply, causing undervoltage resets.
- Running the CM5 hard without cooling.
- Leaving the boot jumper on after flashing.
- Assuming every CM4 carrier supports the CM5 fully.
Frequently asked questions
Is the CM5 compatible with CM4 carriers?
It shares the connector and many carriers work, but check power and feature support.
What power supply do I need?
Use the carrier's rated supply, usually 5 V 5 A, or more with NVMe and USB loads.
Does the CM5 need cooling?
Yes, for sustained loads. Use the official cooler or a good heatsink.
Can it boot from NVMe?
Yes, on carriers with an M.2 slot, after setting the boot order.
What is the CM5 to Pi 5 adapter for?
It lets a CM5 fit Pi 5 cases and accessories for testing.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

