Component guide · Beginner · 3 min read
Digital Watt Meter and DC Power Analyser (150A)

Wiring and Readings
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A DC watt meter sits in line between a battery or supply and a load and shows voltage, current, power, amp-hours and watt-hours. It is the easiest way to measure motor and ESC current on drones, check solar charging, or test battery capacity. The 150 A version handles big brushless setups for short bursts.
Key specs at a glance
- Voltage
- About 0 to 60 V
- Current
- Up to 150 A peak (shorter bursts)
- Readings
- V, A, W, Ah, Wh, peaks
- Connectors
- Thick leads or XT60/Deans
- Power
- From the source side
- Direction
- Source side and load side marked
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the Digital watt meter and power analyser is
A DC watt meter sits between a power source and a load and shows voltage, current, power, amp-hours and watt-hours.
Connect the source to the SOURCE side and the load to the LOAD side; reversed, it reads nothing or wrongly.
Use it for short motor tests at high current; the shunt heats up at sustained high load.
Digital watt meter and power analyser pinout
The pins on the Digital watt meter and power analyser and what each one does.
| Pin | Function |
|---|---|
| SOURCE | Battery or supply |
| LOAD | ESC, motor or device |
- SOURCE
- Battery or supply
- LOAD
- ESC, motor or device
Wiring the Digital watt meter and power analyser
Connect the Digital watt meter and power analyser like this.
| Digital watt meter and power analyser pin | Drone test | Solar check |
|---|---|---|
| SOURCE | LiPo battery | Solar controller battery output |
| LOAD | ESC | Inverter or load |
- SOURCE
- Drone test:
- LiPo battery
- Solar check:
- Solar controller battery output
- LOAD
- Drone test:
- ESC
- Solar check:
- Inverter or load
Example code
A minimal sketch to check the part works.
Charge battery fully, connect a known load through the meter,
run until cut-off voltage, read Ah and Wh.Setup and tuning
connect the source to the SOURCE side and the load to the LOAD side.
stay within about 60 V; higher voltage damages the meter.
short bursts up to the peak rating are fine; use thick leads for high current.
the meter is powered from the source side; it needs about 4 V or more to start.
reset the Ah and Wh counters before each test.
What you need
Shop this list2 of 2 found in our store · ₹827
Digital Watt Meter and Power Analyser: the part this guide coversDigital Watt Meter and Power Analyser₹650
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- INA219 current sensor: logs from a microcontroller.
- Bench power supply.
Common mistakes to avoid
- Connecting the source and load sides the wrong way round.
- Using it above its voltage limit.
- Measuring AC mains.
- Forgetting to reset counters before a capacity test.
Frequently asked questions
Can I measure motor current with this meter?
Yes. Put it between the battery and ESC to see current, peak current and power.
How do I test a battery's capacity?
Fully charge it, connect a load through the meter, and read Ah or Wh at cut-off.
Why is the display blank?
It is powered from the source side; check that side is connected and above about 4 V.
Can it measure AC?
No. It is for DC only.
Can I leave it connected?
Yes, but it draws a little current and adds resistance, so remove it for best efficiency.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
