Component guide · Intermediate · 4 min read
Draw-Wire and Magnetostrictive Sensors

SOP WPS-S-R-500, WPS-XS-R-1000 and WPS-S-R-2000 String Potentiometers, TE Connectivity SP2-50 Position Sensor and FirstRate FST400 Magnetostrictive Displacement Sensors with 4-20 mA
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
For strokes of half a metre to several metres, a rod potentiometer becomes too long. A draw-wire sensor has a steel cable on a spring drum turning a multi-turn potentiometer, so it measures long travel from a small box. Magnetostrictive sensors (FirstRate FST400) use a moving magnet ring along a sealed rod with no contact, giving very long life and 4-20 mA output for hydraulic cylinders and tanks.
Key specs at a glance
- Draw-wire range
- 500, 1000, 2000mm (SOP); 50 inches (TE SP2-50)
- Draw-wire output
- 5 kΩ potentiometer
- Magnetostrictive
- FirstRate FST400 around 1000mm, 4-20 mA
- Supply
- Up to 28V on pots; 24V DC for FST400
- Protection
- IP65 on WPS
- Life
- Draw-wire: cable cycles; magnetostrictive: contactless
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1SOP WPS-S-R-2000 Draw Wire Linear Displacement Sensor, 2000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,599
Option 2SOP WPS-S-R-500 0-500mm Rope Displacement Sensor, 5K Resistance Output, IP65, 1m Cable₹7,749
Option 3SOP WPS-XS-R-1000 Draw Wire Linear Displacement Sensor, 1000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,049
Option 4TE Connectivity SP2-50 Position Sensor, Resistive Position, 50″ Range, SP2 Series₹57,551
Option 5FirstRate FST400-1000 Magnetostrictive Displacement Sensor, 950-1000mm Range, 4-20mA Output, M18x1.5 Port, IP67₹38,359
Option 6FirstRate FST400-3000 Magnetostrictive Displacement Sensor, Range 950-1000mm, 4-20mA Output, 24VDC, Built-In Cylinder Rod Type₹40,449
What the Draw-wire (string pot) and magnetostrictive displacement sensors: SOP WPS, TE SP2 and FirstRate FST400 is
Draw-wire sensors measure long linear travel with a steel cable on a spring drum, and magnetostrictive sensors measure position along a rod without contact.
Mount a draw-wire sensor so the cable leaves the drum straight, in line with the motion; an angled cable wears quickly and reads long. Never let the cable snap back freely, as it can break the spring or the pot.
Magnetostrictive sensors need the magnet ring to move along the rod at the stated gap. Read the 4-20 mA output across a 250Ω resistor or a PLC current input, and scale 4 mA to the start and 20 mA to the end of the range.
Draw-wire (string pot) and magnetostrictive displacement sensors: SOP WPS, TE SP2 and FirstRate FST400 pinout
The pins on the Draw-wire (string pot) and magnetostrictive displacement sensors: SOP WPS, TE SP2 and FirstRate FST400 and what each one does.
| Pin | Function |
|---|---|
| Pot end 1 | Supply |
| Wiper | Output |
| Pot end 2 | Ground |
| FST400 V+ | 24V DC |
| FST400 Iout | 4-20 mA |
- Pot end 1
- Supply
- Wiper
- Output
- Pot end 2
- Ground
- FST400 V+
- 24V DC
- FST400 Iout
- 4-20 mA
Wiring the Draw-wire (string pot) and magnetostrictive displacement sensors: SOP WPS, TE SP2 and FirstRate FST400
Fix the cable end with the supplied clip, and fit a guide pulley if the path has to bend.
| Draw-wire (string pot) and magnetostrictive displacement sensors: SOP WPS, TE SP2 and FirstRate FST400 pin | Arduino | Note |
|---|---|---|
| Pot ends | 5V and GND | Draw-wire as a divider |
| Wiper | A0 | Average readings |
| FST400 4-20 mA | 250Ω to GND, ADC across it | 1-5V range |
- Pot ends
- Arduino:
- 5V and GND
- Note:
- Draw-wire as a divider
- Wiper
- Arduino:
- A0
- Note:
- Average readings
- FST400 4-20 mA
- Arduino:
- 250Ω to GND, ADC across it
- Note:
- 1-5V range
Example code
Set STROKE_MM to the draw-wire range, for example 1000 for WPS-XS-R-1000.
// Wire the sensor as a voltage divider: ends to 5V and GND, wiper to A0.
const float STROKE_MM = 150.0; // electrical stroke of your sensor
int rawMin = 20; // reading at fully retracted (calibrate)
int rawMax = 1003; // reading at fully extended (calibrate)
void setup() { Serial.begin(9600); }
void loop() {
long sum = 0;
for (int i = 0; i < 16; i++) sum += analogRead(A0); // average out noise
float raw = sum / 16.0;
float mm = (raw - rawMin) * STROKE_MM / (rawMax - rawMin);
Serial.print("Position "); Serial.print(mm, 1); Serial.println(" mm");
delay(100);
}Setup and tuning
pull the draw-wire cable straight out from the housing; side angles wear it.
never let the cable fly back; it damages the drum.
wire the draw-wire pot as a voltage divider and read it with an ADC.
read magnetostrictive outputs with a 250 Ω resistor or a 4-20 mA receiver module.
24 V DC for magnetostrictive sensors; pots can run on 5 V.
What you need
Shop this list8 of 9 found in our store · ₹1,64,873
SOP WPS-S-R-2000 Draw Wire Linear Displacement Sensor, 2000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable: the part this guide coversSOP WPS-S-R-2000 Draw Wire Linear Displacement Sensor, 2000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,599
SOP WPS-S-R-500 0-500mm Rope Displacement Sensor, 5K Resistance Output, IP65, 1m Cable: another version this guide coversSOP WPS-S-R-500 0-500mm Rope Displacement Sensor, 5K Resistance Output, IP65, 1m Cable₹7,749
SOP WPS-XS-R-1000 Draw Wire Linear Displacement Sensor, 1000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable: another version this guide coversSOP WPS-XS-R-1000 Draw Wire Linear Displacement Sensor, 1000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,049
TE Connectivity SP2-50 Position Sensor, Resistive Position, 50″ Range, SP2 Series: another version this guide coversTE Connectivity SP2-50 Position Sensor, Resistive Position, 50″ Range, SP2 Series₹57,551
FirstRate FST400-1000 Magnetostrictive Displacement Sensor, 950-1000mm Range, 4-20mA Output, M18x1.5 Port, IP67: another version this guide coversFirstRate FST400-1000 Magnetostrictive Displacement Sensor, 950-1000mm Range, 4-20mA Output, M18x1.5 Port, IP67₹38,359
FirstRate FST400-3000 Magnetostrictive Displacement Sensor, Range 950-1000mm, 4-20mA Output, 24VDC, Built-In Cylinder Rod Type: another version this guide coversFirstRate FST400-3000 Magnetostrictive Displacement Sensor, Range 950-1000mm, 4-20mA Output, 24VDC, Built-In Cylinder Rod Type₹40,449- Uno R3 development board: the controller used in the wiring tableFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- Linear position sensors: all types.
- Potentiometric displacement sensors: shorter strokes.
- SICK MPS cylinder sensors: pneumatic cylinders.
Common mistakes to avoid
- Letting the cable snap back into the housing.
- Pulling the cable at an angle.
- Reading a 4-20 mA output without a resistor.
- Running long unshielded wires for analog signals.
Frequently asked questions
How long can a draw-wire sensor measure?
These models measure about 500 mm to 2000 mm.
How do I read a 4-20 mA sensor with Arduino?
Pass the current through a 250 Ω resistor and read 1 to 5 V, or use a receiver module.
What is a magnetostrictive sensor used for?
Hydraulic cylinder and machine positions, where contact-free measurement lasts long.
Why are my readings noisy?
Use shielded cable and average readings; pot outputs pick up noise over long runs.
Can I use it outdoors?
Many models are IP65 or better; check the rating.
Parts for this guide
SOP WPS-S-R-2000 Draw Wire Linear Displacement Sensor, 2000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,599View- ₹7,749View
SOP WPS-XS-R-1000 Draw Wire Linear Displacement Sensor, 1000mm Stroke, 5KΩ Analog Output, 24VDC, 1m Cable₹10,049View- ₹57,551View
FirstRate FST400-1000 Magnetostrictive Displacement Sensor, 950-1000mm Range, 4-20mA Output, M18x1.5 Port, IP67₹38,359View
FirstRate FST400-3000 Magnetostrictive Displacement Sensor, Range 950-1000mm, 4-20mA Output, 24VDC, Built-In Cylinder Rod Type₹40,449View- ₹359View
- ₹49View
- ₹68View
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

