Component guide · Intermediate · 4 min read
ESP32-C5 Dual-Band Wi-Fi 6 Boards and Modules

5 GHz Setup and Pins
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-C5 is the first Espressif chip with dual-band Wi-Fi 6, so it can join 5 GHz networks as well as 2.4 GHz. It is a single-core RISC-V chip at 240 MHz with BLE 5 and 802.15.4 for Thread and Zigbee. It suits devices in crowded Wi-Fi areas or networks where 2.4 GHz is busy. The ESP32-C61 is a lower-cost 2.4 GHz Wi-Fi 6 relative.
Key specs at a glance
- CPU
- Single-core RISC-V 240 MHz, LP core
- Wireless
- Wi-Fi 6 2.4 and 5 GHz, BLE 5, 802.15.4
- Memory
- Up to 16 MB flash and 8 MB PSRAM by module
- USB
- USB serial/JTAG
- Boards
- Espressif DevKitC-1, Waveshare C5 boards and Zero, XIAO ESP32-C5
- C61
- 2.4 GHz Wi-Fi 6 plus BLE, PSRAM support
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Espressif ESP32-C5-DevKitC-1-N8R4 Wi-Fi 6 & BLE Development Board₹1,338
Option 2Espressif ESP32-C5-DevKitC-1-N8R8 Wi-Fi 6 & BLE Dev Board₹1,829
Option 3Espressif ESP32-C5-MINI-1-N4 Wi-Fi 6 & BLE Module₹339
Option 4Espressif ESP32-C5-WROOM-1U-N8R8 Wi-Fi 6 & BLE Module₹419
Option 5Waveshare ESP32-C5 Dual-Band Wi-Fi 6 Dev Board w/ ESP32-C5-WROOM-1-N32R8₹1,339
Option 6Waveshare ESP32-C5 Wi-Fi 6 & BLE 5 Development Board w/ 16MB Flash & 8MB PSRAM₹1,239
What the ESP32-C5 Wi-Fi 6 dual-band board is
The ESP32-C5 is a RISC-V microcontroller with dual-band Wi-Fi 6 (2.4 and 5 GHz), Bluetooth LE and 802.15.4 for Thread and Zigbee, sold on small dev boards with USB.
Support for the C5 arrived in ESP-IDF 5.5 and Arduino-ESP32 3.3. Use current versions; older cores do not list the chip. To force 5 GHz, set the band mode in code or connect to a 5 GHz-only SSID.
Wi-Fi 6 target wake time lets battery sensors sleep longer between beacons, and 802.15.4 allows Thread and Matter devices.
ESP32-C5 Wi-Fi 6 dual-band board pinout
The pins on the ESP32-C5 Wi-Fi 6 dual-band board and what each one does.
| Pin | Function |
|---|---|
| USB | Native USB serial/JTAG |
| GPIO 28 | BOOT on DevKitC-1 (check your board) |
| GPIO 27 | RGB LED on DevKitC-1 |
| 3V3 / 5V / GND | Power |
| U.FL | External antenna on 1U modules |
- USB
- Native USB serial/JTAG
- GPIO 28
- BOOT on DevKitC-1 (check your board)
- GPIO 27
- RGB LED on DevKitC-1
- 3V3 / 5V / GND
- Power
- U.FL
- External antenna on 1U modules
Wiring the ESP32-C5 Wi-Fi 6 dual-band board
Pin numbers differ between C5 boards; use the maker's pinout. Fit an antenna on U.FL versions before connecting to Wi-Fi.
| ESP32-C5 Wi-Fi 6 dual-band board pin | I2C sensor | XIAO ESP32-C5 |
|---|---|---|
| VCC | 3V3 | 3V3 |
| GND | GND | GND |
| SDA | Any free GPIO | Any free GPIO |
| SCL | Any free GPIO | Any free GPIO |
- VCC
- I2C sensor:
- 3V3
- XIAO ESP32-C5:
- 3V3
- GND
- I2C sensor:
- GND
- XIAO ESP32-C5:
- GND
- SDA
- I2C sensor:
- Any free GPIO
- XIAO ESP32-C5:
- Any free GPIO
- SCL
- I2C sensor:
- Any free GPIO
- XIAO ESP32-C5:
- Any free GPIO
Example code
Needs Arduino-ESP32 3.3 or newer and board ESP32C5 Dev Module (or the XIAO entry). Band mode names follow the current Arduino-ESP32 API.
#include <WiFi.h>
void setup() {
Serial.begin(115200);
WiFi.setBandMode(WIFI_BAND_MODE_5G_ONLY); // or WIFI_BAND_MODE_AUTO
WiFi.begin("YOUR_5G_SSID", "YOUR_PASSWORD");
while (WiFi.status() != WL_CONNECTED) { delay(300); Serial.print("."); }
Serial.printf("\nConnected, channel %d, RSSI %d\n", WiFi.channel(), WiFi.RSSI());
}
void loop() {}Setup and tuning
install the latest ESP32 Arduino core (3.x) or ESP-IDF 5.x; older cores do not list the C5.
feed 5 V over USB; all GPIO are 3.3 V only.
plug in USB; if upload fails, hold BOOT, tap RESET, then release BOOT.
connect to a 5 GHz network for less crowded channels; the board picks the band from the SSID.
keep the PCB antenna end clear of metal and the ground plane of other boards.
What you need
Shop this list14 of 14 found in our store · ₹79,919
Espressif ESP32-C5-DevKitC-1-N8R4 Wi-Fi 6 & BLE Development Board: the part this guide coversEspressif ESP32-C5-DevKitC-1-N8R4 Wi-Fi 6 & BLE Development Board₹1,338
Espressif ESP32-C5-DevKitC-1-N8R8 Wi-Fi 6 & BLE Dev Board: another version this guide coversEspressif ESP32-C5-DevKitC-1-N8R8 Wi-Fi 6 & BLE Dev Board₹1,829
Espressif ESP32-C5-MINI-1-N4 Wi-Fi 6 & BLE Module: another version this guide coversEspressif ESP32-C5-MINI-1-N4 Wi-Fi 6 & BLE Module₹339
Espressif ESP32-C5-WROOM-1U-N8R8 Wi-Fi 6 & BLE Module: another version this guide coversEspressif ESP32-C5-WROOM-1U-N8R8 Wi-Fi 6 & BLE Module₹419
Waveshare ESP32-C5 Dual-Band Wi-Fi 6 Dev Board w/ ESP32-C5-WROOM-1-N32R8: another version this guide coversWaveshare ESP32-C5 Dual-Band Wi-Fi 6 Dev Board w/ ESP32-C5-WROOM-1-N32R8₹1,339
Waveshare ESP32-C5 Wi-Fi 6 & BLE 5 Development Board w/ 16MB Flash & 8MB PSRAM: another version this guide coversWaveshare ESP32-C5 Wi-Fi 6 & BLE 5 Development Board w/ 16MB Flash & 8MB PSRAM₹1,239
Waveshare ESP32-C5-Zero Mini Development Board w/o Headers: another version this guide coversWaveshare ESP32-C5-Zero Mini Development Board w/o Headers₹739
Seeed Studio Studio XIAO ESP32-C5 Dual-Band Wi-Fi 6 IoT Dev Board (Unsoldered): another version this guide coversKikobot C1 6-Axis Robotic Arm for Education and Research₹70,800
Espressif ESP32-C61-DevKitC-1-N8R2 Wi-Fi 6 & BLE 5 Dev Board: another version this guide coversEspressif ESP32-C61-DevKitC-1-N8R2 Wi-Fi 6 & BLE 5 Dev Board₹1,039
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
IPEX to SMA pigtail cable: for an external dual-band antenna5cm RG178 IPEX 1 to RP-SMA Female RF Pigtail Cable₹82Closest match, check the specs
Alternatives and when to choose them
- ESP32-C6 boards: 2.4 GHz Wi-Fi 6 with Zigbee and Thread.
- BW16 RTL8720DN: another dual-band Wi-Fi option.
- ESP32-H2 boards: Thread and Zigbee without Wi-Fi.
Common mistakes to avoid
- Using an old ESP32 core that has no ESP32-C5 board entry.
- Driving GPIO pins with 5 V signals.
- Expecting dual-core FreeRTOS tasks like on the classic ESP32.
- Placing the antenna over a metal enclosure or ground plane.
Frequently asked questions
Does the ESP32-C5 really support 5 GHz Wi-Fi?
Yes. It is the first ESP32 chip with dual-band 2.4 and 5 GHz Wi-Fi 6.
Can I use the Arduino IDE with it?
Yes, with ESP32 Arduino core 3.1 or newer; older cores do not include it.
Is the ESP32-C5 dual core?
No. It has one RISC-V core at up to 240 MHz plus a low-power core.
Can it run Thread or Zigbee?
Yes. The 802.15.4 radio supports Thread and Zigbee, for example for Matter devices.
Are the GPIO pins 5 V tolerant?
No. Keep every pin at 3.3 V and use level shifting for 5 V parts.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


