Component guide · Intermediate · 3 min read
ESP32-H2 SuperMini and DevKit Boards

Zigbee, Thread and BLE Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The ESP32-H2 is a low-power RISC-V chip with 802.15.4 (Zigbee and Thread) and Bluetooth LE, but no Wi-Fi. It is made for battery sensors and switches that join a Zigbee hub, a Thread border router or a Matter network. Small SuperMini, Waveshare and WeAct boards make it easy to try, and Arduino-ESP32 includes Zigbee examples.
Key specs at a glance
- CPU
- Single-core RISC-V 96 MHz
- Radio
- IEEE 802.15.4 (Zigbee 3.0, Thread 1.3) and BLE 5
- Wi-Fi
- None
- Memory
- 320 KB SRAM, 2 or 4 MB flash
- USB
- USB serial/JTAG
- Low power
- Deep sleep current a few microamps
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ESP32-H2 SuperMini Development Board₹449
Option 2Waveshare ESP32-H2 DevKit, 96MHz RISC-V, BLE & 802.15.4 Module₹779
Option 3Waveshare ESP32-H2 Mini Development Board w/ ESP32-H2FH4S & 4MB Flash₹439
Option 4WeAct Studio ESP32H2-N4-A Development Board w/ ESP32-H2-MINI-1₹1,059
Option 5M5Stack ESP32-H2 Thread/Zigbee Gateway Module₹889
What the ESP32-H2 Thread and Zigbee board is
In Arduino, Tools > Zigbee mode selects end device or coordinator, and the examples cover lights, switches, temperature sensors and more. A Zigbee end device on an H2 can pair with Home Assistant through ZHA or Zigbee2MQTT.
Because there is no Wi-Fi, an H2 cannot reach the internet alone; a hub or border router does that. The M5Stack H2 module pairs with an M5 controller to act as a gateway.
ESP32-H2 Thread and Zigbee board pinout
The pins on the ESP32-H2 Thread and Zigbee board and what each one does.
| Pin | Function |
|---|---|
| USB | Native USB serial/JTAG |
| GPIO 9 | BOOT |
| GPIO 8 | RGB LED on many boards |
| 3V3 / 5V / GND | Power |
| ADC | GPIO 1 to 5 |
- USB
- Native USB serial/JTAG
- GPIO 9
- BOOT
- GPIO 8
- RGB LED on many boards
- 3V3 / 5V / GND
- Power
- ADC
- GPIO 1 to 5
Wiring the ESP32-H2 Thread and Zigbee board
Pins vary by board; check the pinout. Power sensors from 3.3 V only.
| ESP32-H2 Thread and Zigbee board pin | I2C sensor | Alternative |
|---|---|---|
| VCC | 3V3 | 3V3 |
| GND | GND | GND |
| SDA | GPIO 12 | Any free GPIO |
| SCL | GPIO 22 | Any free GPIO |
- VCC
- I2C sensor:
- 3V3
- Alternative:
- 3V3
- GND
- I2C sensor:
- GND
- Alternative:
- GND
- SDA
- I2C sensor:
- GPIO 12
- Alternative:
- Any free GPIO
- SCL
- I2C sensor:
- GPIO 22
- Alternative:
- Any free GPIO
Example code
Select ESP32H2 Dev Module, Zigbee mode: Zigbee ED (end device) and a partition scheme with Zigbee. Put your hub in pairing mode before the board starts.
#include "Zigbee.h"
#define EP 10
ZigbeeTempSensor zbTemp(EP);
void setup() {
zbTemp.setManufacturerAndModel("Geekobot", "H2Temp");
zbTemp.setMinMaxValue(-20, 80);
Zigbee.addEndpoint(&zbTemp);
Zigbee.begin(); // join an open Zigbee network
while (!Zigbee.connected()) delay(100);
}
void loop() {
float t = temperatureRead(); // chip temperature as a demo
zbTemp.setTemperature(t);
zbTemp.reportTemperature();
delay(10000);
}Setup and tuning
use Zigbee2MQTT, ZHA or a Zigbee hub to pair the device.
use ESP-IDF or esp-matter examples with a Thread border router.
use deep sleep and report on change for months of runtime.
erase flash when switching between Zigbee and Thread firmware.
What you need
Shop this list10 of 10 found in our store · ₹27,721
ESP32-H2 SuperMini Development Board: the part this guide coversESP32-H2 SuperMini Development Board₹449
Waveshare ESP32-H2 DevKit, 96MHz RISC-V, BLE & 802.15.4 Module: another version this guide coversWaveshare ESP32-H2 DevKit, 96MHz RISC-V, BLE & 802.15.4 Module₹779
Waveshare ESP32-H2 Mini Development Board w/ ESP32-H2FH4S & 4MB Flash: another version this guide coversWaveshare ESP32-H2 Mini Development Board w/ ESP32-H2FH4S & 4MB Flash₹439
WeAct Studio ESP32H2-N4-A Development Board w/ ESP32-H2-MINI-1: another version this guide coversWeAct Studio ESP32H2-N4-A Development Board w/ ESP32-H2-MINI-1₹1,059
M5Stack ESP32-H2 Thread/Zigbee Gateway Module: another version this guide coversM5Stack ESP32-H2 Thread/Zigbee Gateway Module₹889
USB Type-C cable 1 m: a data cable for programming (not charge-only)24-Core USB Type-C Cable, 1 m₹500Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
DS18B20 waterproof temperature probe: a first sensor to readSonoff DS18B20 Waterproof Temperature Sensor Probe w/ 1m Cable – 1-Wire Interface₹340Closest match, check the specs
Home Assistant Green: a hub to pair Zigbee devices withHome Assistant Green Smart Home Hub₹23,149Closest match, check the specs
Alternatives and when to choose them
- ESP32-C6 boards: Zigbee and Thread plus Wi-Fi.
- ESP32-C5 boards: dual-band Wi-Fi 6 plus 802.15.4.
- Sonoff Zigbee dongle: a coordinator for your hub.
Common mistakes to avoid
- Expecting Wi-Fi.
- Wrong Zigbee mode or partition scheme in Arduino.
- Hub not in pairing mode.
- Mixing Thread and Zigbee firmware without erasing.
Frequently asked questions
Does the ESP32-H2 have Wi-Fi?
No.
Can it be a Zigbee coordinator?
Yes in Arduino and ESP-IDF, though most people use a USB dongle.
Is it Matter compatible?
Yes, over Thread with esp-matter.
How long on a coin cell?
Months for a sensor reporting every few minutes with deep sleep.
H2 or C6?
C6 if you also need Wi-Fi; H2 for the lowest power.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

