Component guide · Beginner · 5 min read
ESP32 Maker Dev Boards

Adafruit Feather HUZZAH32 and ItsyBitsy ESP32, Unexpected Maker FeatherS3 Neo, DFRobot FireBeetle and Romeo ESP32-S3, ESP32-PICO-KIT and DevKitM-2, ESP32-S3-USB-OTG, ESP8684 (ESP32-C2) Boards, LilyGO Micro-32, T-Encoder and T-Energy S3, Wemos 18650, ACEBOTT ESP32 Max and DMX Controller
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are ESP32 boards from makers beyond the plain DevKit. Feather boards (HUZZAH32, FeatherS3 Neo) and FireBeetle add LiPo charging and low sleep current for battery sensors. ItsyBitsy and PICO-KIT are small. ESP8684 boards use the low-cost ESP32-C2. ESP32-S3-USB-OTG is for USB host projects. LilyGO T-Energy and Wemos 18650 boards hold an 18650 cell.
Key specs at a glance
- Chips
- ESP32, ESP32-S3, ESP32-C2 (ESP8684), ESP32-PICO-D4
- Battery
- LiPo charger on Feather, FireBeetle, ItsyBitsy; 18650 holder on T-Energy and Wemos
- USB
- USB-serial bridge or native USB on S3
- Extras
- Camera on Romeo S3, rotary encoder and LED ring on T-Encoder, DMX512 on DFR0944
- Form factor
- Feather, ItsyBitsy, Pmod, DevKit, Arduino Uno (ACEBOTT)
- Software
- Arduino ESP32 core, ESP-IDF, MicroPython, CircuitPython (S3)
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1ACEBOTT ESP32 Max V1.0 Development Board w/ Type-C Cable₹1,129
Option 2ACEBOTT ESP32 Max V3.0 Development Board w/ Type-C Cable₹1,379
Option 3Adafruit HUZZAH32 ESP32 Feather Board (Pre-Soldered)₹3,929
Option 4Adafruit HUZZAH32 ESP32 Feather Board w/ Stacking Headers₹3,109
Option 5Adafruit HUZZAH32 ESP32 Feather Board w/ WROOM32 Module₹3,659
Option 6Adafruit ItsyBitsy ESP32 – PCB Antenna, 8 MB Flash / 2 MB PSRAM₹1,760
What the ESP32 maker dev boards (Feather HUZZAH32, FeatherS3 Neo, FireBeetle, ItsyBitsy, PICO-KIT, ESP8684, LilyGO, Wemos 18650) is
ESP32 Feather and maker dev boards are compact ESP32 boards with USB, a LiPo charger and standard headers, such as the Adafruit Feather ESP32, TinyPICO and similar.
For battery projects, choose a board with a low deep-sleep current (FireBeetle, FeatherS3 Neo) and measure it: USB-serial chips and power LEDs on other boards waste battery.
ESP-LAUNCHER and ESP-FactoryTB2 are Espressif test and programming boards for modules on a production line, not general dev boards. The Pmod ESP32 adds Wi-Fi to FPGA and Digilent boards over UART.
ESP32 maker dev boards (Feather HUZZAH32, FeatherS3 Neo, FireBeetle, ItsyBitsy, PICO-KIT, ESP8684, LilyGO, Wemos 18650) pinout
The pins on the ESP32 maker dev boards (Feather HUZZAH32, FeatherS3 Neo, FireBeetle, ItsyBitsy, PICO-KIT, ESP8684, LilyGO, Wemos 18650) and what each one does.
| Pin | Function |
|---|---|
| USB | Power, flashing and serial (CP2102, CH340, CH9102 or native USB) |
| EN / RST | Reset |
| BOOT / GPIO0 | Hold low to enter the bootloader |
| 3V3 / GND | 3.3V supply out |
| GPIO | 3.3V logic only |
- USB
- Power, flashing and serial (CP2102, CH340, CH9102 or native USB)
- EN / RST
- Reset
- BOOT / GPIO0
- Hold low to enter the bootloader
- 3V3 / GND
- 3.3V supply out
- GPIO
- 3.3V logic only
Wiring the ESP32 maker dev boards (Feather HUZZAH32, FeatherS3 Neo, FireBeetle, ItsyBitsy, PICO-KIT, ESP8684, LilyGO, Wemos 18650)
ESP GPIO is 3.3V. Avoid boot strapping pins (GPIO0, 2, 12, 15 on ESP32; GPIO0, 2, 15 on ESP8266) for inputs that may be pulled at power-up.
| ESP32 maker dev boards (Feather HUZZAH32, FeatherS3 Neo, FireBeetle, ItsyBitsy, PICO-KIT, ESP8684, LilyGO, Wemos 18650) pin | Connection | Note |
|---|---|---|
| USB | To PC | Install the USB-serial driver if needed |
| Sensors | I2C or SPI pins | 3.3V logic |
| Battery | JST LiPo on Feather-style boards | 1S only |
- USB
- Connection:
- To PC
- Note:
- Install the USB-serial driver if needed
- Sensors
- Connection:
- I2C or SPI pins
- Note:
- 3.3V logic
- Battery
- Connection:
- JST LiPo on Feather-style boards
- Note:
- 1S only
Example code
Pin A0 maps to a different GPIO on each board; check the board's pinout. Turn off Wi-Fi before sleep for the lowest current.
#include <WiFi.h>
RTC_DATA_ATTR int boots = 0; // survives deep sleep
void setup() {
Serial.begin(115200);
boots++;
int raw = analogRead(A0); // battery or sensor on an ADC pin
Serial.printf("boot %d, A0 = %d\n", boots, raw);
// connect Wi-Fi and send the reading here
esp_sleep_enable_timer_wakeup(10ULL * 60 * 1000000); // 10 minutes
esp_deep_sleep_start();
}
void loop() {}Setup and tuning
install the ESP32 core and pick the exact board name so pins and LEDs map correctly.
some boards use native USB; if the port disappears, double-tap reset or hold BOOT.
plug a 3.7 V single-cell LiPo into the JST jack; check the polarity first.
GPIO are 3.3 V only; avoid strapping pins at boot.
stack add-on boards on the headers; they share I2C and SPI.
What you need
Shop this list20 of 20 found in our store · ₹41,335
ACEBOTT ESP32 Max V1.0 Development Board w/ Type-C Cable: the part this guide coversACEBOTT ESP32 Max V1.0 Development Board w/ Type-C Cable₹1,129
ACEBOTT ESP32 Max V3.0 Development Board w/ Type-C Cable: another version this guide coversACEBOTT ESP32 Max V3.0 Development Board w/ Type-C Cable₹1,379
Adafruit HUZZAH32 ESP32 Feather Board (Pre-Soldered): another version this guide coversAdafruit HUZZAH32 ESP32 Feather Board (Pre-Soldered)₹3,929
Adafruit HUZZAH32 ESP32 Feather Board w/ Stacking Headers: another version this guide coversAdafruit HUZZAH32 ESP32 Feather Board w/ Stacking Headers₹3,109
Adafruit HUZZAH32 ESP32 Feather Board w/ WROOM32 Module: another version this guide coversAdafruit HUZZAH32 ESP32 Feather Board w/ WROOM32 Module₹3,659
Adafruit ItsyBitsy ESP32 – PCB Antenna, 8 MB Flash / 2 MB PSRAM: another version this guide coversAdafruit ItsyBitsy ESP32 – PCB Antenna, 8 MB Flash / 2 MB PSRAM₹1,760
DFRobot FireBeetle 2 ESP32-E IoT Development Board: another version this guide coversDFRobot FireBeetle 2 ESP32-E IoT Development Board₹879
DFRobot FireBeetle ESP32 IoT Microcontroller w/ Wi-Fi & Bluetooth: another version this guide coversDFRobot FireBeetle ESP32 IoT Microcontroller w/ Wi-Fi & Bluetooth₹1,469
DFRobot FireBeetle ESP32-E IoT Microcontroller w/ Header: another version this guide coversDFRobot FireBeetle ESP32-E IoT Microcontroller w/ Header₹1,469
DFRobot Romeo ESP32-S3 Robotics Development Board w/ OV2640 Camera: another version this guide coversDFRobot Romeo ESP32-S3 Robotics Development Board w/ OV2640 Camera₹6,049
Digilent Pmod ESP32 Wireless Communication Module: another version this guide coversDigilent Pmod ESP32 Wireless Communication Module₹4,289
ESP32-C2-M1 WiFi Serial Transparent Transmission Module: another version this guide coversESP32-C2-M1 WiFi Serial Transparent Transmission Module₹369
Espressif ESP32-PICO-DevKitM-2 Development Board: another version this guide coversEspressif ESP32-PICO-DevKitM-2 Development Board₹1,561
Espressif ESP32-PICO-KIT Development Board: another version this guide coversEspressif ESP32-PICO-KIT Development Board₹1,023
Espressif ESP32-S3-USB-OTG Development Board: another version this guide coversEspressif ESP32-S3-USB-OTG Development Board₹4,695
Espressif ESP8684-DevKitC-02C-N4 Dev Board w/ Wi-Fi & BLE 5.0: another version this guide coversEspressif ESP8684-DevKitC-02C-N4 Dev Board w/ Wi-Fi & BLE 5.0₹1,042
Espressif ESP8684-DevKitC-02C-N4X Development Board w/ ESP32-MINI-1: another version this guide coversEspressif ESP8684-DevKitC-02C-N4X Development Board w/ ESP32-MINI-1₹1,359
Espressif ESP8684-DevKitM-1-H4X Wi-Fi & BLE Development Board: another version this guide coversEspressif ESP8684-DevKitM-1-H4X Wi-Fi & BLE Development Board₹1,469
Espressif ESP8684-MINI-1-H2X Wi-Fi & BLE 5.3 Module: another version this guide coversEspressif ESP8684-MINI-1-H2X Wi-Fi & BLE 5.3 Module₹188
LilyGO Micro-32 V2.0 ESP32 PICO-D4 Wi-Fi Bluetooth Module: another version this guide coversLilyGO Micro-32 V2.0 ESP32 PICO-D4 Wi-Fi Bluetooth Module₹509
Alternatives and when to choose them
- ESP32 WROOM DevKit: the standard board.
- ESP32-S3 DevKitC: official S3 board.
- ESP32-C3 boards: low-cost RISC-V boards.
Common mistakes to avoid
- Plugging in a LiPo with reversed JST polarity.
- Selecting a generic ESP32 board so pins do not match.
- Feeding 5 V signals into 3.3 V pins.
- Stacking two wings that use the same pins.
Frequently asked questions
Can I charge a LiPo on a Feather board?
Yes. The board charges a single 3.7 V cell over USB.
Why does the JST battery plug not fit or match?
JST PH polarity is not standard; check red to + before plugging in.
Are FeatherWings compatible with every Feather?
Mostly, but check the pin names because some boards differ.
Why can I not upload to my board?
Hold BOOT, tap RESET and try again; some boards need the right USB mode.
Can I read the battery voltage?
Many boards have a divider on a pin; read it with analogRead and scale it.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.









