Component guide · Beginner · 4 min read
FM and Audio RF Modules

TEA5767 I2C FM Radio Receiver, BH1417F Stereo FM Transmitter, DSP PLL 87-108MHz FM Transmitter with LCD, Mini FM Transmitter with Mic, Walkie-Talkie Transceiver Board, MT8870 DTMF Decoder and 38kHz IR Transmitter
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These modules handle simple audio radio jobs. The TEA5767 is an FM radio receiver tuned over I2C, so an Arduino can build a digital FM radio. BH1417F and the PLL board with LCD are low-power stereo FM transmitters for sending audio to a nearby radio. The MT8870 decodes DTMF phone tones into 4-bit numbers, handy for phone or radio-controlled relays.
Key specs at a glance
- TEA5767
- 76-108MHz FM receiver, I2C 0x60, 5V or 3.3V
- FM transmitters
- 87-108MHz, short range, line or mic input
- Walkie board
- Two-way radio transceiver PCB
- MT8870
- DTMF to 4-bit output plus StD strobe
- IR transmitter
- 38kHz IR LED driver, digital input
- Supply
- 3-5V on most, 12V on PLL board
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1BH1417F FM Radio Transmitter Module₹1,900
Option 2DSP PLL Stereo FM Transmitter Module w/ LCD Display 87-108MHz₹1,219
Option 3Mini FM Transmitter Module with Microphone₹400
Option 4TEA5767 FM Radio Receiver Module w/ I2C Interface₹239
Option 5Two-way Radio Transceiver Circuit Board for Walkie-talkie₹824
Option 6MT8870 DTMF Decoder Module₹82
What the FM radio, FM transmitter, walkie-talkie, DTMF and IR transmitter modules is
FM radio and audio RF modules such as the TEA5767, RDA5807 and Si4703 receivers and the KT0803 transmitter let a microcontroller tune, receive or send FM audio.
Build an FM radio with a TEA5767 and an LCD, and a small amplifier like the PAM8403 for the speaker. Use an FM transmitter to send a phone or Pi's audio to a car or home radio; keep power very low and choose an empty frequency. Use the MT8870 to control relays by pressing phone keys during a call through a GSM module's audio output.
The IR transmitter sends TV remote codes using the IRremote library, letting a microcontroller control TVs and ACs.
FM radio, FM transmitter, walkie-talkie, DTMF and IR transmitter modules pinout
The pins on the FM radio, FM transmitter, walkie-talkie, DTMF and IR transmitter modules and what each one does.
| Pin | Function |
|---|---|
| SDA / SCL | I2C (TEA5767) |
| L / R audio | Audio in or out |
| Q1-Q4 | DTMF data out (MT8870) |
| StD | Valid tone strobe (MT8870) |
| DAT / IN | Signal in (IR transmitter) |
- SDA / SCL
- I2C (TEA5767)
- L / R audio
- Audio in or out
- Q1-Q4
- DTMF data out (MT8870)
- StD
- Valid tone strobe (MT8870)
- DAT / IN
- Signal in (IR transmitter)
Wiring the FM radio, FM transmitter, walkie-talkie, DTMF and IR transmitter modules
Fit the telescopic or wire antenna to the TEA5767 for good reception.
| FM radio, FM transmitter, walkie-talkie, DTMF and IR transmitter modules pin | Connection | Note |
|---|---|---|
| TEA5767 SDA / SCL | A4 / A5 | Uno I2C |
| TEA5767 audio | PAM8403 input | To speaker |
| MT8870 Q1-Q4 | D4-D7 | Read on StD high |
| IR TX DAT | D3 | IRremote send pin |
- TEA5767 SDA / SCL
- Connection:
- A4 / A5
- Note:
- Uno I2C
- TEA5767 audio
- Connection:
- PAM8403 input
- Note:
- To speaker
- MT8870 Q1-Q4
- Connection:
- D4-D7
- Note:
- Read on StD high
- IR TX DAT
- Connection:
- D3
- Note:
- IRremote send pin
Example code
The TEA5767 library adds search and signal level. FM transmitters are regulated; use the lowest power that works.
#include <Wire.h>
void tune(float mhz) {
unsigned int pll = 4 * (mhz * 1000000 + 225000) / 32768;
Wire.beginTransmission(0x60);
Wire.write(pll >> 8);
Wire.write(pll & 0xFF);
Wire.write(0xB0); // high side injection, stereo
Wire.write(0x10); // 32.768kHz crystal
Wire.write(0x00);
Wire.endTransmission();
}
void setup() {
Wire.begin();
tune(93.5); // set your local station
}
void loop() {}Setup and tuning
connect SDA and SCL over I2C at 3.3 V, with a common ground, and use a library that supports the chip.
solder a wire of about 75 cm (a quarter wave at 100 MHz) to the antenna pin, or use the headphone cable where the module does that.
feed the line output into an amplifier such as the PAM8403; it cannot drive a speaker on its own.
set the frequency in 0.1 MHz steps and read the signal strength to auto-scan.
keep power very low and follow local rules for unlicensed FM.
What you need
Shop this list9 of 10 found in our store · ₹4,822
BH1417F FM Radio Transmitter Module: the part this guide coversBH1417F FM Radio Transmitter Module₹1,900
DSP PLL Stereo FM Transmitter Module w/ LCD Display 87-108MHz: another version this guide coversDSP PLL Stereo FM Transmitter Module w/ LCD Display 87-108MHz₹1,219
Mini FM Transmitter Module with Microphone: another version this guide coversMini FM Transmitter Module with Microphone₹400
TEA5767 FM Radio Receiver Module w/ I2C Interface: another version this guide coversTEA5767 FM Radio Receiver Module w/ I2C Interface₹239
Two-way Radio Transceiver Circuit Board for Walkie-talkie: another version this guide coversTwo-way Radio Transceiver Circuit Board for Walkie-talkie₹824
MT8870 DTMF Decoder Module: another version this guide coversMT8870 DTMF Decoder Module₹82
Digital 38kHz Infrared Transmitter Module: another version this guide coversDigital 38kHz Infrared Transmitter Module₹41- Uno R3 development board: the controller used in the wiring tableFind this part
Dupont jumper wires: for the connectionsDupont Jumper Wires (40 pcs)₹49Closest match, check the specs
Solderless breadboard: to build without solderingSolderless Breadboard₹68
Alternatives and when to choose them
- Bluetooth audio receiver modules: wireless audio over BT.
- 433MHz RF: data remotes.
- SDR receivers: receive many bands.
Common mistakes to avoid
- Powering a 3.3 V module from 5 V.
- Leaving out the antenna wire.
- Wiring a speaker straight to the line output.
- Transmitting on a frequency a station already uses.
Frequently asked questions
Can the TEA5767 drive a speaker directly?
No. Its output is line level, so add a small amplifier such as the PAM8403.
Why do I hear only noise from the receiver?
Attach a 75 cm wire antenna, keep it away from the board and tune to a strong station.
Which Arduino library supports the RDA5807?
The Radio library by Matthias Hertel supports the RDA5807, TEA5767 and Si4703.
Can these modules show the station name?
Yes, the RDA5807 and Si4703 decode RDS station names and text; the TEA5767 cannot.
Is it legal to use a small FM transmitter?
Rules differ by country; keep power very low and never transmit on an occupied station.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

