Component guide · Intermediate · 5 min read
BLHeli_S 4-in-1 ESCs

SpeedyBee BLS 50A and 60A, Flywoo GOKU, GEPRC BLS60A and Taker H60, Hobbywing XRotor G2, BotDrive, DarkMatter and EMAX
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A 4-in-1 ESC puts four motor controllers on one board that stacks under the flight controller, saving weight and wiring. BLHeli_S boards use 8-bit chips; they are cheaper, run cool and, flashed with Bluejay firmware, support bidirectional DShot for RPM filtering. Pick the current rating for your motors, the mounting size (20x20 or 30x30) and the battery voltage range.
Key specs at a glance
- Current
- 35A to 65A per motor (continuous)
- Voltage
- 2S to 6S LiPo
- Firmware
- BLHeli_S, Bluejay
- Protocol
- DShot150/300/600, bidirectional with Bluejay
- Mounting
- 20x20 or 30.5x30.5 mm
- Extras
- Current sensor on most; no telemetry wire
This part can carry many amps. Use wire thick enough for the current, put a fuse close to the battery, check that connectors are rated for the load and give drivers and motors room to cool. A short at these currents melts wires in seconds.
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1SpeedyBee BLS 50A 30×30 4-in-1 ESC 3-6S LiPo₹4,130
Option 2SpeedyBee BLS 60A 30×30 4-in-1 ESC₹4,822
Option 3SpeedyBee 35A BLHeli_S Mini 4-in-1 ESC (3-6S)₹6,229
Option 4Flywoo GOKU BS35A 35A 4-in-1 BLHeli_S ESC₹4,649
Option 5Flywoo GOKU 40A 2-6S 8bit 4-in-1 BLHeli_S ESC₹4,651
Option 6Flywoo GOKU 506S 50A 3-6S BL_S 4-in-1 ESC₹5,009
What the FPV 4-in-1 ESCs (BLHeli_S / 8-bit) is
FPV 4-in-1 ESCs with BLHeli_S or Bluejay firmware drive all four drone motors from one board, taking DShot commands from the flight controller.
Rate the ESC at least 20 to 30% above the motor's peak current from its thrust table. For 5 inch freestyle on 6S, 45 to 60A boards are typical.
The EMAX 4x30A is an older 2-4S board for 250-class quads. The Flywoo 6-in-1 board drives hexacopters and other six-motor frames.
FPV 4-in-1 ESCs (BLHeli_S / 8-bit) pinout
The pins on the FPV 4-in-1 ESCs (BLHeli_S / 8-bit) and what each one does.
| Pin | Function |
|---|---|
| Battery pads (+ / -) | Main LiPo input; solder the XT60 lead and the capacitor here |
| Motor pads M1 to M4 | Three pads per motor; any order, fix direction in software |
| FC connector (8-pin) | VBAT, GND, current, telemetry and four signal lines to the flight controller |
| Low-ESR capacitor | Soaks up voltage spikes; always fit one across the battery pads |
- Battery pads (+ / -)
- Main LiPo input; solder the XT60 lead and the capacitor here
- Motor pads M1 to M4
- Three pads per motor; any order, fix direction in software
- FC connector (8-pin)
- VBAT, GND, current, telemetry and four signal lines to the flight controller
- Low-ESR capacitor
- Soaks up voltage spikes; always fit one across the battery pads
Wiring the FPV 4-in-1 ESCs (BLHeli_S / 8-bit)
Compare the pin order printed on the ESC and flight controller before plugging the 8-pin cable; brands differ. Use a smoke stopper for the first power-up, with props off.
| FPV 4-in-1 ESCs (BLHeli_S / 8-bit) pin | Connection | Note |
|---|---|---|
| Battery | XT60 lead + capacitor to the battery pads | Thick wire, short as possible |
| Flight controller | 8-pin cable (check pin order) | Wrong order can kill both boards |
| Motors | Three wires each to M1 to M4 | Swap direction in BLHeli or Betaflight |
- Battery
- Connection:
- XT60 lead + capacitor to the battery pads
- Note:
- Thick wire, short as possible
- Flight controller
- Connection:
- 8-pin cable (check pin order)
- Note:
- Wrong order can kill both boards
- Motors
- Connection:
- Three wires each to M1 to M4
- Note:
- Swap direction in BLHeli or Betaflight
Example code
Flash Bluejay on BLHeli_S ESCs (esc-configurator.com) to get bidirectional DShot and RPM filtering. BLHeli_32 and AM32 support it out of the box.
# In Betaflight Configurator > CLI
set motor_pwm_protocol = DSHOT600
set dshot_bidir = ON # needs Bluejay (BLHeli_S) or BLHeli_32 / AM32
set motor_poles = 14 # count the magnets on your motor bell
save
# Motor direction (props off, battery on):
# Motors tab > Motor direction > pick motor > reverse
# Or in the ESC: BLHeli Configurator / ESC-Configurator > Motor DirectionSetup and tuning
match the mount pattern (20x20 or 30x30 mm) and connect the flight controller with the supplied ribbon cable.
flash Bluejay through the ESC configurator to get bidirectional DShot and RPM filtering.
solder a low-ESR capacitor (for example 1000 µF 35 V for 6S) on the battery pads.
set DShot300 or DShot600 in Betaflight.
check order and direction in the Betaflight motor tab with props off.
stay below the continuous rating; burst ratings last only seconds.
What you need
Shop this list19 of 19 found in our store · ₹82,432
SpeedyBee BLS 50A 30×30 4-in-1 ESC 3-6S LiPo: the part this guide coversSpeedyBee BLS 50A 30×30 4-in-1 ESC 3-6S LiPo₹4,130
SpeedyBee BLS 60A 30×30 4-in-1 ESC: another version this guide coversSpeedyBee BLS 60A 30×30 4-in-1 ESC₹4,822
SpeedyBee 35A BLHeliS Mini 4-in-1 ESC (3-6S): another version this guide coversSpeedyBee 35A BLHeli_S Mini 4-in-1 ESC (3-6S)₹6,229
Flywoo GOKU BS35A 35A 4-in-1 BLHeliS ESC: another version this guide coversFlywoo GOKU BS35A 35A 4-in-1 BLHeli_S ESC₹4,649
Flywoo GOKU 40A 2-6S 8bit 4-in-1 BLHeliS ESC: another version this guide coversFlywoo GOKU 40A 2-6S 8bit 4-in-1 BLHeli_S ESC₹4,651
Flywoo GOKU 506S 50A 3-6S BLS 4-in-1 ESC: another version this guide coversFlywoo GOKU 506S 50A 3-6S BL_S 4-in-1 ESC₹5,009
Flywoo GOKU CubePilot BS13A 6-in-1 BLHeliS ESC: another version this guide coversFlywoo GOKU CubePilot BS13A 6-in-1 BLHeli_S ESC₹4,216
GEPRC BLS60A 3-6S 4-in-1 BLHeliS ESC DShot600: another version this guide coversGEPRC BLS60A 3-6S 4-in-1 BLHeli_S ESC DShot600₹4,949
GEPRC TAKER H60BLS 60A 4-in-1 BLHeliS ESC: another version this guide coversGEPRC TAKER H60_BLS 60A 4-in-1 BLHeli_S ESC₹4,949
Hobbywing XRotor FPV G2 4-in-1 ESC 45A: another version this guide coversHobbywing XRotor FPV G2 4-in-1 ESC 45A₹6,439
Hobbywing XRotor FPV G2 4-in-1 65A BLHeliS ESC: another version this guide coversHobbywing XRotor FPV G2 4-in-1 65A BLHeli_S ESC₹5,499
Hobbywing XRotor FPV G2 65A 4-in-1 ESC: another version this guide coversHobbywing XRotor FPV G2 65A 4-in-1 ESC₹6,279
BotDrive 8-bit 50A 4-in-1 ESC (3-6S LiPo): another version this guide coversBotDrive 8-bit 50A 4-in-1 ESC (3-6S LiPo)₹4,499
DarkMatter VISHNU 50 MK-III 4-in-1 50A 8Bit BLHelis ESC: another version this guide coversDarkMatter VISHNU 50 MK-III 4-in-1 50A 8Bit BLHeli_s ESC₹5,212
35A 2-5S BLHeliS 4-in-1 ESC: another version this guide covers35A 2-5S BLHeli_S 4-in-1 ESC₹4,466
EMAX 4x30A 2-4S 4-in-1 ESC for Multirotor: another version this guide coversEMAX 4x30A 2-4S 4-in-1 ESC for Multirotor₹3,454
BLHeli USB linker programmer: flashes and configures ESCs without a flight controllerBLHeli USB Linker Programmer for BLHeli_S / BLHeli_32 ESCs₹609Closest match, check the specs
iFlight XT30/XT60 smart smoke stopper: protects a new build on first power-upiFlight XT30/XT60 Smart Smoke Stopper 2-6S LiPo₹979Closest match, check the specs
2S 7.4V LiPo battery pack (XT60): a small battery for bench testingBonka 2S 7.4V LiPo Battery Pack (1000 to 4200mAh, XT60)₹1,392Closest match, check the specs
Alternatives and when to choose them
- BLHeli_32 and AM32 4-in-1 ESCs: 32-bit, telemetry.
- FC and ESC stacks: matched pairs.
- Single FPV ESCs: one per arm.
Common mistakes to avoid
- Leaving out the low-ESR capacitor.
- Testing motors with props fitted.
- Running 6S on a 4S-rated ESC.
- Bridging pads with solder when wiring motors.
Frequently asked questions
What is Bluejay firmware for BLHeli_S ESCs?
Open firmware for BLHeli_S ESCs that adds bidirectional DShot, RPM filtering and startup tunes.
Why does my ESC need a capacitor?
It absorbs voltage spikes from the motors that can otherwise kill the ESC.
Which DShot rate should I use?
DShot300 suits most builds; DShot600 suits 8 kHz loop rates.
How do I test the motor order safely?
Remove the props, open the Betaflight motor tab and spin each motor one at a time.
Can I run a 6S battery on a 4S ESC?
No. The FETs and capacitors are not rated for it; use a 6S-rated ESC.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
