How-to · Intermediate · 3 min read
GT2 Timing Belts and Pulleys
Sizes, Tension and Steps per mm
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
GT2 timing belts have teeth 2 mm apart and are the standard drive for 3D printer X and Y axes. The common size is a 6 mm wide belt with a 20-tooth, 5 mm bore pulley on a 1.8 degree stepper. At 1/16 microstepping that gives 80 steps per mm. Tension the belt so it twangs like a low guitar string but does not bind.
Key specs at a glance
- Pitch
- 2 mm between teeth (GT2)
- Width
- 6 mm is the most common; 9 mm for heavier machines
- Pulleys
- 16T and 20T on 5 mm shafts; 8 mm bore for some motors
- Idlers
- Smooth or toothed, often 16T or 20T with a 3 mm bore
- Steps per mm
- 200 × microsteps ÷ (teeth × 2 mm)
- Belt core
- Fibreglass or steel for stretch resistance
Steps per mm for a GT2 belt
The firmware needs steps per millimetre. For a 200-step motor at 1/16 microstepping, the formula is:
steps/mm = (200 × 16) ÷ (pulley teeth × 2 mm)
A 20-tooth pulley gives 3200 ÷ 40 = 80 steps/mm. A 16-tooth pulley gives 100 steps/mm. Use the steps per mm calculator with your own microstepping.
Choosing belts and pulleys
Match the belt width to the pulley and the machine.
| Part | Common option | Notes |
|---|---|---|
| Belt | GT2 6 mm, closed loop or open length | Closed loops have a fixed length; open belts you cut and clamp |
| Motor pulley | 20T 5 mm bore for NEMA 17 | 16T gives finer resolution, 20T gives more speed |
| Idler pulley | 20T smooth or toothed, 3 or 5 mm bore | Smooth idlers run on the back of the belt |
| Belt width | 6 mm for printers, 9 mm for CNC or large machines | Wider belts are stiffer |
- Belt
- Common option:
- GT2 6 mm, closed loop or open length
- Notes:
- Closed loops have a fixed length; open belts you cut and clamp
- Motor pulley
- Common option:
- 20T 5 mm bore for NEMA 17
- Notes:
- 16T gives finer resolution, 20T gives more speed
- Idler pulley
- Common option:
- 20T smooth or toothed, 3 or 5 mm bore
- Notes:
- Smooth idlers run on the back of the belt
- Belt width
- Common option:
- 6 mm for printers, 9 mm for CNC or large machines
- Notes:
- Wider belts are stiffer
Setting belt tension
Belts that are too loose cause ghosting and layer shifts. Too tight loads the motor and bearings. A good starting point is a belt that gives a clear low note when plucked, can be pressed in a few millimetres by a finger, and does not make the axis rumble. Check that both X belts are equal. Use the printer maker's manual if it gives a tension method.
Maintenance and troubleshooting
check tension and bolted joints before changing slicer settings.
misaligned pulleys; align the pulley with the idler.
tighten the grub screw onto the shaft flat and add threadlock.
idler bearing worn; replace.
note the routing and the number of teeth engaged at each end.
Try it: Stepper steps per mm calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Buying a belt of the wrong pitch (GT2 vs GT3 vs MXL).
- Using a bore that does not match the shaft.
- Over-tightening the belt and killing the bearings.
- Leaving the pulley screw loose on the motor shaft.
- Forgetting to update steps per mm after changing pulley teeth.
Frequently asked questions
Is GT2 the same as 2GT?
Yes, it is the same profile with a 2 mm pitch.
What belt width should I buy?
6 mm for most printers. Check your printer's current belt.
How do I know if the belt is too loose?
You will see ghosting or layer shifts, and the belt will sag or slap when the axis moves.
Can I cut a belt to length?
Yes, with open-length belts. Use clamps or locks at each end.
Which is better, 16T or 20T?
16T is finer, 20T is faster. Many machines use 20T.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 2 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




