Component guide · Beginner · 3 min read
Honeywell MPR Pressure Sensor

Adafruit MPRLS Ported 0 to 25 psi and SparkFun Qwiic MicroPressure 25 psi
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Both boards carry the Honeywell MPR series sensor, a calibrated 0 to 25 psi absolute pressure sensor with a small metal port for a tube. They are ideal for pumps, vacuum, soft robotics, blood pressure cuffs and pneumatics. Plug in with a STEMMA QT or Qwiic cable, push a tube on the port and read pressure in hPa or psi with the maker's library.
Key specs at a glance
- Range
- 0 to 25 psi absolute (about 0 to 1724 hPa)
- Accuracy
- About ±1.5% FS
- Interface
- I2C at 0x18
- Supply
- 3.3 V (boards accept 3.3 to 5 V)
- Port
- Stainless steel tube port
- Connector
- STEMMA QT or Qwiic
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
What the Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure) is
The Honeywell MPR (MicroPressure) sensor is a tiny calibrated pressure sensor with I2C or SPI output, used in wearables, medical devices and small air or fluid systems.
Absolute means it reads about 14.7 psi (1013 hPa) at sea level with the port open. Subtract that baseline for gauge pressure.
Keep liquids out; the sensor is for dry air and non-corrosive gases.
Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure) pinout
The pins on the Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure) and what each one does.
| Pin | Function |
|---|---|
| VIN / 3V3 | Supply |
| GND | Ground |
| SDA / SCL | I2C |
| EOC | End of conversion (optional) |
| RST | Reset (optional) |
- VIN / 3V3
- Supply
- GND
- Ground
- SDA / SCL
- I2C
- EOC
- End of conversion (optional)
- RST
- Reset (optional)
Wiring the Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure)
Connect the Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure) like this.
| Honeywell MPR (Adafruit MPRLS and SparkFun MicroPressure) pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5V (or 3.3V) | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
- VCC
- Arduino Uno:
- 5V (or 3.3V)
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
Example code
SparkFun's MicroPressure library works on both boards: readPressure(PSI).
#include <Wire.h>
#include <Adafruit_MPRLS.h>
Adafruit_MPRLS mpr(-1, -1); // no reset or EOC pins
float base = 0;
void setup() {
Serial.begin(115200);
if (!mpr.begin()) { Serial.println("MPR not found"); while (1); }
base = mpr.readPressure(); // port open to air
}
void loop() {
float hpa = mpr.readPressure();
Serial.print(hpa, 1); Serial.print(" hPa abs ");
Serial.print(hpa - base, 1); Serial.println(" hPa gauge");
delay(200);
}Setup and tuning
connect VCC (3.3 V), GND, SDA and SCL; breakouts like the SparkFun MPR board have pull-ups.
use the SparkFun MicroPressure library for Arduino.
choose the pressure range (such as 0 to 25 psi) and type (gauge or absolute) for your use.
connect tubing to the sensor port; do not press on the port.
use only with dry air or non-corrosive gas unless rated for liquids.
What you need
Shop this list5 of 6 found in our store · ₹10,639
Adafruit MPRLS Ported Pressure Sensor Breakout – 0 to 25 PSI, Stainless Steel Port, I2C Interface: the part this guide coversAdafruit MPRLS Ported Pressure Sensor Breakout – 0 to 25 PSI, Stainless Steel Port, I2C Interface₹4,719
SparkFun Qwiic MicroPressure Sensor – 25psi Absolute Pressure, I2C Interface: another version this guide coversSparkFun Qwiic MicroPressure Sensor – 25psi Absolute Pressure, I2C Interface₹5,229
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
HX710B air pressure sensor module (0 to 40 kPa): a ready pressure module with ADCHX710B Air Pressure Sensor Module (0-40 kPa) with Straight Header – Analog Voltage Output₹163
Alternatives and when to choose them
- HX710B modules: lower cost 40 kPa.
- GZP I2C sensors: many ranges.
- BMP390: barometer without a port.
Common mistakes to avoid
- Using a gas-only sensor with liquids.
- Confusing gauge and absolute readings.
- Pressing on the sensor port.
- Powering the bare sensor with 5 V.
Frequently asked questions
How do I read the MPR sensor with Arduino?
Use the SparkFun MicroPressure library over I2C.
Is the MPR gauge or absolute?
Both versions exist; check the part number.
Can it measure water pressure?
Only versions rated for liquid media; most are for dry gas.
Why do readings not match a gauge?
Check gauge versus absolute and unit conversion.
Can I use it at 5 V?
The bare sensor is 3.3 V; use a breakout with a regulator for 5 V boards.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


