Component guide · Intermediate · 3 min read
Inductors Explained
How They Work, Ratings and Choosing One
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
An inductor is a coil of wire that stores energy in a magnetic field and resists changes in current. That makes it the key part in buck and boost converters, filters and chokes. When choosing one, match the inductance (in microhenries), make sure the saturation current is above the peak current in your circuit, check the RMS (heating) current rating, and prefer low DC resistance (DCR) for efficiency.
Key specs at a glance
- Unit
- Henry (H); power inductors are usually 1 to 100 µH
- Saturation current (Isat)
- Above this, inductance collapses
- RMS current (Irms)
- Current that causes a set temperature rise
- DCR
- DC resistance of the winding; lower is more efficient
- Types
- Power (shielded/unshielded), ferrite bead, common-mode choke, RF
- Marking
- Code like 101 = 100 µH, 4R7 = 4.7 µH
What an inductor does
Current through a coil creates a magnetic field. When the current tries to change, the field produces a voltage that opposes the change (V = L x dI/dt). So an inductor lets steady DC through (apart from its small resistance) but resists fast changes. In a buck converter, the switch pulses the inductor and it smooths those pulses into steady current; in a boost converter, the inductor's stored energy is released at a higher voltage. In filters, an inductor with a capacitor blocks high-frequency noise.
Ratings that matter
| Rating | What it means | Why it matters |
|---|---|---|
| Inductance (µH) | How strongly it resists current change | Set by the converter or filter design |
| Saturation current | Current where inductance drops (often by 20 to 30%) | Exceeding it causes current spikes and failures |
| RMS / heating current | Current giving about 40 °C temperature rise | Exceeding it overheats the part |
| DCR | Winding resistance | Loss = I² x DCR; lower is better |
| Shielding | Magnetic field kept inside the core | Less noise coupling into nearby circuits |
| Self-resonant frequency | Above this it acts like a capacitor | Matters in RF and fast switching |
- Inductance (µH)
- What it means:
- How strongly it resists current change
- Why it matters:
- Set by the converter or filter design
- Saturation current
- What it means:
- Current where inductance drops (often by 20 to 30%)
- Why it matters:
- Exceeding it causes current spikes and failures
- RMS / heating current
- What it means:
- Current giving about 40 °C temperature rise
- Why it matters:
- Exceeding it overheats the part
- DCR
- What it means:
- Winding resistance
- Why it matters:
- Loss = I² x DCR; lower is better
- Shielding
- What it means:
- Magnetic field kept inside the core
- Why it matters:
- Less noise coupling into nearby circuits
- Self-resonant frequency
- What it means:
- Above this it acts like a capacitor
- Why it matters:
- Matters in RF and fast switching
Choosing an inductor for a DC-DC converter
Use the inductance the converter IC's datasheet recommends (for example 33 µH for an LM2596 at 3 A, or 4.7 to 22 µH for small modern bucks). Then pick a part whose saturation current is at least 20 to 30% above the peak inductor current (output current plus half the ripple) and whose RMS rating covers the output current. Prefer shielded parts near sensitive circuits. Replacing a module's inductor with a smaller one of the same value but lower current rating is a common cause of failure. See DC-DC converters.
Ferrite beads and chokes
A ferrite bead is a lossy inductor that turns high-frequency noise into heat while passing DC; it is used on power lines to noisy chips and on cables (the lump on a USB or monitor lead). A common-mode choke has two windings that block noise travelling on both wires together while letting the wanted signal through; it appears on mains inputs and USB lines. Neither replaces a power inductor in a converter.
Try it: RL time constant calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing by inductance alone and ignoring saturation current.
- Using a tiny signal inductor in a power converter.
- Placing an unshielded inductor next to a sensitive analog circuit.
- Reading 101 as 101 µH instead of 100 µH.
- Using a ferrite bead where a power inductor is needed.
Frequently asked questions
What does an inductor do in a circuit?
It stores energy in a magnetic field and resists changes in current. It is used to smooth current in converters and to filter noise.
What is inductor saturation current?
The current at which the core can store no more magnetic energy and inductance drops sharply. Stay below it with margin.
How do I read an inductor code like 100 or 4R7?
It works like resistor codes in microhenries: 100 is 10 µH, 101 is 100 µH, and 4R7 is 4.7 µH.
Can I replace an inductor with a higher value?
Sometimes, but it changes converter ripple and stability. Follow the IC datasheet; current rating usually matters more.
What is the difference between an inductor and a ferrite bead?
An inductor stores energy with low loss; a ferrite bead is designed to absorb high-frequency noise as heat.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Würth Elektronik and Coilcraft inductor selection guides
- Texas Instruments LM2596 datasheet (inductor selection)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



