Buying guide · Advanced · 3 min read
Legged Robots
Quadrupeds, Hexapods and Humanoid Kits
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Legged robots walk using servos at each joint: a quadruped usually has 8 or 12, a hexapod 18 and a small humanoid 16 or more. Hexapods are the most stable because three legs always touch the ground. Quadrupeds are cheaper and more dynamic, and humanoids are the hardest to balance. The hard parts are servo torque, a power supply that can feed every servo at once, and walking code using gaits and inverse kinematics.
Key specs at a glance
- Quadruped
- 8 to 12 servos; small SG90 kits to MG996R or bus-servo dogs
- Hexapod
- 18 servos (3 per leg), very stable tripod gait
- Humanoid
- 16 to 20+ servos, needs balance and a gyro
- Servos
- Metal-gear, high torque; bus servos for feedback
- Controller
- PCA9685 + Arduino/ESP32, or a dedicated servo controller
- Power
- 2S LiPo or 6 to 7.4 V supply, often 5 to 15 A peak
Which type to build
| Type | Servos | Difficulty | Notes |
|---|---|---|---|
| Mini quadruped (spider) | 8 | Beginner to intermediate | SG90 servos, good first walking robot |
| Robot dog | 12 | Intermediate to advanced | Needs stronger servos and IK code |
| Hexapod | 18 | Intermediate | Most stable, big power draw |
| Humanoid | 16+ | Advanced | Balance, falls, high cost |
- Mini quadruped (spider)
- Servos:
- 8
- Difficulty:
- Beginner to intermediate
- Notes:
- SG90 servos, good first walking robot
- Robot dog
- Servos:
- 12
- Difficulty:
- Intermediate to advanced
- Notes:
- Needs stronger servos and IK code
- Hexapod
- Servos:
- 18
- Difficulty:
- Intermediate
- Notes:
- Most stable, big power draw
- Humanoid
- Servos:
- 16+
- Difficulty:
- Advanced
- Notes:
- Balance, falls, high cost
Servos, controllers and power
Each joint holds the robot's weight, so torque matters more than speed. Plastic-gear micro servos work for very light spider kits; heavier builds need metal-gear servos or serial bus servos that report position and load.
A PCA9685 board drives 16 PWM servos from two I2C pins; use two for a hexapod. Power is the usual failure: 18 servos can pull many amps, so use a high-current battery or a buck converter rated for the peak, thick wires, and a separate supply for the controller. See robot power planning.
Gaits and inverse kinematics
Start with pre-recorded poses played in sequence. To walk properly, use a gait: a hexapod's tripod gait moves three legs while the other three hold the body. Inverse kinematics (IK) calculates the joint angles needed to put each foot at a target point, so you can steer, turn and change body height smoothly. Many kits come with apps and example code; open-source projects for robot dogs and hexapods provide IK libraries. Add an MPU6050 to level the body on slopes.
Try it: Motor power torque calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Underpowered servos that cannot lift the body.
- A supply that browns out when all servos move.
- Powering servos from the Arduino 5 V pin.
- Starting with a humanoid as a first legged robot.
- Setting servo horns without centring the servos first.
Frequently asked questions
Which legged robot is best for beginners?
A small 8-servo spider quadruped kit, then a hexapod.
Why does my hexapod collapse?
Servos lack torque or the supply drops under load. Use stronger servos and a higher-current battery.
What is inverse kinematics?
Maths that turns a desired foot position into the joint angles needed to reach it.
Can I use SG90 servos for a robot dog?
Only for very small, light builds. Larger dogs need metal-gear or bus servos.
How do I control a hexapod?
Two PCA9685 boards or a servo controller with an ESP32, controlled by an app, a joystick or a PS2 remote.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- Servo manufacturer torque specifications (TowerPro, Feetech)
- Open-source hexapod and quadruped IK project documentation
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




