Component guide · Intermediate · 3 min read
Robotic Arms and Grippers
Servos, DOF and Building One
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A hobby robot arm is a chain of joints, each driven by a servo or motor. Four degrees of freedom (base, shoulder, elbow, gripper) is enough to pick and place small objects; six adds wrist rotation and tilt. The shoulder needs the most torque. Power the servos from a separate 5 to 6 V supply, drive them through a PCA9685 board, and start with joint-by-joint control.
Key specs at a glance
- 4-DOF
- Base, shoulder, elbow, gripper
- 6-DOF
- Adds wrist pitch and rotation
- Servos
- SG90/MG90S for light arms; MG996R or 15 to 60 kg·cm servos for bigger ones
- Driver
- PCA9685 for up to 16 servos, or smart serial bus servos
- Power
- Separate 5 to 6 V, several amps
- Control
- Joint angles, then inverse kinematics for X, Y, Z moves
Types of hobby arms
| Arm type | Actuators | Strengths | Limits |
|---|---|---|---|
| Acrylic 4-DOF kit | SG90 / MG90S servos | Cheap, great for learning | Wobbly, small loads |
| Metal 6-DOF kit | MG996R or digital servos | Stronger and stiffer | Needs a strong supply, servo jitter |
| Smart servo arm | Serial bus servos with feedback | Position and load feedback, smooth | Higher cost |
| Stepper arm | NEMA 17 steppers with gearing | Precise, strong | Needs homing and stepper drivers |
| Desktop collaborative arm | Integrated motors and controller | Ready to program, repeatable | Most expensive |
- Acrylic 4-DOF kit
- Actuators:
- SG90 / MG90S servos
- Strengths:
- Cheap, great for learning
- Limits:
- Wobbly, small loads
- Metal 6-DOF kit
- Actuators:
- MG996R or digital servos
- Strengths:
- Stronger and stiffer
- Limits:
- Needs a strong supply, servo jitter
- Smart servo arm
- Actuators:
- Serial bus servos with feedback
- Strengths:
- Position and load feedback, smooth
- Limits:
- Higher cost
- Stepper arm
- Actuators:
- NEMA 17 steppers with gearing
- Strengths:
- Precise, strong
- Limits:
- Needs homing and stepper drivers
- Desktop collaborative arm
- Actuators:
- Integrated motors and controller
- Strengths:
- Ready to program, repeatable
- Limits:
- Most expensive
Working out shoulder torque
Torque = force x distance. Add up the weight of everything beyond the shoulder (links, elbow servo, gripper and load) and multiply by its distance from the shoulder axis when the arm is stretched out horizontally. Example: an elbow servo of 55 g at 10 cm, a gripper of 40 g at 18 cm and a 50 g load at 20 cm need about 0.55 + 0.72 + 1.0 = 2.3 kg·cm. A 1.8 kg·cm SG90 would struggle; an MG996R (about 9 to 11 kg·cm) has plenty of margin. Aim for at least two times margin.
Controlling the arm
- 1Joint control: set each servo angle with a PCA9685; move slowly in small steps to avoid jerks.
- 2Record and replay: use potentiometers on a small 'master' arm or sliders in a web page (ESP32) to record positions and play them back.
- 3Inverse kinematics (IK): compute joint angles from a target X, Y, Z position with simple trigonometry for a 3-link arm; libraries and ROS MoveIt do this for bigger arms.
- 4Feedback: smart servos report position and load, so you can detect when the gripper has closed on an object.
Grippers
the most common; one micro servo opens and closes the jaws.
fingers stay parallel; better for boxes.
a small pump and suction cup lift flat, smooth objects.
picks up steel parts.
Do not drive a gripper servo hard against an object for long; it stalls and overheats. Close until contact, then back off a few degrees.
Try it: Motor power torque calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Powering servos from the Arduino 5V pin.
- Undersizing the shoulder servo.
- Snapping servos to new angles instantly, which shakes the arm.
- Holding a stalled gripper servo closed.
- Building a 6-DOF arm from SG90s and expecting it to lift anything.
Frequently asked questions
How many DOF does a robot arm need?
Four degrees of freedom handles simple pick and place. Six lets the gripper reach positions at any orientation.
Which servo is best for a robot arm?
MG996R or stronger digital servos for the base, shoulder and elbow; MG90S for the wrist and gripper on small arms.
How do I power a robot arm with many servos?
Use a separate 5 to 6 V supply rated for several amps, connected to the servo power rail of a PCA9685 board, with a common ground.
Can Arduino control a 6-DOF robot arm?
Yes. A PCA9685 board drives the six servos over I2C, leaving pins free for buttons, potentiometers or Bluetooth.
What is inverse kinematics?
Calculating the joint angles needed to put the gripper at a chosen position. It turns 'move to X, Y, Z' into servo angles.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




