Component guide · Beginner · 4 min read
LoRa and Sub-GHz Antennas

433MHz Folding and Magnetic, 868MHz and 915MHz SMA and RP-SMA Whips, RG58 Cable Antennas, Helical Spring and Chip, FPC/PCB, Fiberglass Outdoor N-Type, FrSky Super 8 and VHF/UHF Walkie-Talkie
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A LoRa link's range depends more on the antenna than on the module. The antenna must be tuned to your band: 433 MHz or 865-867 MHz (the licence-free band in India, served by 868 MHz antennas). A whip on SMA is the easy choice for nodes, spring and chip antennas fit small enclosures but give less range, and a fiberglass outdoor antenna on a mast is the best upgrade for a gateway.
Key specs at a glance
- Bands
- 433 MHz, 868 MHz, 915 MHz; VHF/UHF on walkie-talkie models
- Gain
- 0.6 to 4.5 dBi on whips; higher on fiberglass
- Types
- Folding whip, magnetic, spring/helical, chip, FPC/PCB, fiberglass
- Connector
- SMA, RP-SMA, u.FL, N-type, or solder pin
- Cable
- None, 1, 3 or 5 m RG58
- Impedance
- 50 ohm
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1433MHz 2.5dBi Omnidirectional Folding Antenna₹187
Option 2AntennaHome Antenna (Rubber and Internal FPC / PCB)₹84
Option 3AntennaHome Fiberglass Outdoor Antenna (N-Type)₹2,980
Option 4AntennaHome Spring, Helical and Chip Antenna (DIP / SMD)₹19
Option 5LWC-868-MM-03 868MHz 4.5dBi SMA Antenna w/ 5m RG58 Cable₹415
Option 6LWC-868-MM-03 868MHz 4dBi SMA Antenna Stub w/ 1m RG58 Cable₹239
What the LoRa and sub-GHz antennas: 433, 868 and 915 MHz whips, spring, PCB, fiberglass and VHF/UHF is
LoRa and sub-GHz antennas for 433, 868 and 915 MHz include spring, whip, PCB and fibreglass antennas that set how far your LoRa, Sigfox or RF modules can reach.
Buy the antenna for the band your module uses, not the module's chip name. An SX1278 board is usually 433 MHz, while SX1262 and most LoRaWAN gear in India run on IN865. A 915 MHz antenna on an 865 MHz radio still works but loses some range; a 433 MHz antenna on 865 MHz works poorly.
Height beats gain. Lifting an antenna two metres often adds more range than a higher-gain model. High-gain fiberglass antennas squash the pattern flat, which is ideal for a rooftop gateway but not for a node on a hill below it. Spring and chip antennas are fine for short links inside a house.
LoRa and sub-GHz antennas: 433, 868 and 915 MHz whips, spring, PCB, fiberglass and VHF/UHF pinout
The pins on the LoRa and sub-GHz antennas: 433, 868 and 915 MHz whips, spring, PCB, fiberglass and VHF/UHF and what each one does.
| Pin | Function |
|---|---|
| SMA / RP-SMA | Screw connector on modules and gateways |
| u.FL / IPEX | Snap connector on small modules |
| N-type | Weatherproof outdoor connector on fiberglass antennas |
| Spring pin | Soldered directly to the ANT pad |
| Chip antenna pads | Need the matching network from the datasheet |
- SMA / RP-SMA
- Screw connector on modules and gateways
- u.FL / IPEX
- Snap connector on small modules
- N-type
- Weatherproof outdoor connector on fiberglass antennas
- Spring pin
- Soldered directly to the ANT pad
- Chip antenna pads
- Need the matching network from the datasheet
Wiring the LoRa and sub-GHz antennas: 433, 868 and 915 MHz whips, spring, PCB, fiberglass and VHF/UHF
Do not transmit without an antenna attached; LoRa modules at 20 to 30 dBm can be damaged by reflected power.
| LoRa and sub-GHz antennas: 433, 868 and 915 MHz whips, spring, PCB, fiberglass and VHF/UHF pin | Connection | Note |
|---|---|---|
| Whip antenna | Module SMA | Vertical |
| Spring antenna | ANT pad | Short, straight lead |
| Fiberglass antenna | Gateway via N to SMA cable | Keep cable short, weatherproof the joint |
| Lightning | Earth the mast | For rooftop gateways |
- Whip antenna
- Connection:
- Module SMA
- Note:
- Vertical
- Spring antenna
- Connection:
- ANT pad
- Note:
- Short, straight lead
- Fiberglass antenna
- Connection:
- Gateway via N to SMA cable
- Note:
- Keep cable short, weatherproof the joint
- Lightning
- Connection:
- Earth the mast
- Note:
- For rooftop gateways
Example code
Run this on the receiver, keep the sender fixed and swap antennas; a higher RSSI and SNR at the same spot means a better antenna for that link.
#include <SPI.h>
#include <LoRa.h>
void setup() {
Serial.begin(115200);
LoRa.setPins(10, 9, 2); // NSS, RESET, DIO0
if (!LoRa.begin(865E6)) { // use 433E6 for 433 MHz boards
Serial.println("LoRa init failed");
while (true);
}
}
void loop() {
if (LoRa.parsePacket()) {
while (LoRa.available()) LoRa.read();
Serial.print("RSSI ");
Serial.print(LoRa.packetRssi());
Serial.print(" dBm SNR ");
Serial.println(LoRa.packetSnr());
}
}Setup and tuning
choose an antenna tuned to your module's frequency, such as 865 to 867 MHz in India.
match SMA, RP-SMA, u.FL or IPEX, and use a short low-loss cable.
mount vertically, as high as possible, clear of metal and walls.
higher-gain antennas focus signal toward the horizon; use them for gateways on masts.
it can damage the radio.
What you need
Shop this list15 of 15 found in our store · ₹7,405
433MHz 2.5dBi Omnidirectional Folding Antenna: the part this guide covers433MHz 2.5dBi Omnidirectional Folding Antenna₹187
AntennaHome Antenna (Rubber and Internal FPC / PCB): another version this guide coversAntennaHome Antenna (Rubber and Internal FPC / PCB)₹84
AntennaHome Fiberglass Outdoor Antenna (N-Type): another version this guide coversAntennaHome Fiberglass Outdoor Antenna (N-Type)₹2,980
AntennaHome Spring, Helical and Chip Antenna (DIP / SMD): another version this guide coversAntennaHome Spring, Helical and Chip Antenna (DIP / SMD)₹19
LWC-868-MM-03 868MHz 4.5dBi SMA Antenna w/ 5m RG58 Cable: another version this guide coversLWC-868-MM-03 868MHz 4.5dBi SMA Antenna w/ 5m RG58 Cable₹415
LWC-868-MM-03 868MHz 4dBi SMA Antenna Stub w/ 1m RG58 Cable: another version this guide coversLWC-868-MM-03 868MHz 4dBi SMA Antenna Stub w/ 1m RG58 Cable₹239
LWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable: another version this guide coversLWC-868-MM-03 868MHz 4dBi SMA Antenna w/ 3m RG58 Cable₹412
Helical Spring Coil Antenna: another version this guide coversHelical Spring Coil Antenna₹40
LoRa Antenna 433MHz SMA Male 3.6dBi: another version this guide coversLoRa Antenna 433MHz SMA Male 3.6dBi₹61
LoRa Antenna 868MHz 0.6dBi RP-SMA: another version this guide coversLoRa Antenna 868MHz 0.6dBi RP-SMA₹64
LoRa Antenna 915MHz 2.2dBi RP-SMA Omnidirectional: another version this guide coversLoRa Antenna 915MHz 2.2dBi RP-SMA Omnidirectional₹71
ReadyToSky TX433-XPA100 433MHz SMA Antenna w/ Magnetic Base: another version this guide coversReadyToSky TX433-XPA100 433MHz SMA Antenna w/ Magnetic Base₹459
Waveshare LPWA LoRa Antenna: another version this guide coversWaveshare LPWA LoRa Antenna₹200
FrSky Super 8 900MHz Antenna for R9M & R9M Lite Module: another version this guide coversFrSky Super 8 900MHz Antenna for R9M & R9M Lite Module₹1,679
AntennaHome Walkie-Talkie Antenna (VHF / UHF): another version this guide coversAntennaHome Walkie-Talkie Antenna (VHF / UHF)₹495
Alternatives and when to choose them
- SX1262 LoRa module: a common radio for these antennas.
- LoRa SX1278: 433 MHz boards.
- LoRaWAN nodes and gateways: where outdoor antennas help most.
- Choosing an antenna: gain and VSWR.
Common mistakes to avoid
- Using an antenna for the wrong band.
- Mixing SMA and RP-SMA connectors.
- Mounting the antenna inside a metal box.
- Transmitting with no antenna fitted.
Frequently asked questions
Which frequency antenna do I need for LoRa in India?
Use an 865 to 867 MHz antenna, the band allowed for LoRa in India.
Will a 433 MHz antenna work on an 868 MHz module?
Poorly. A wrong-band antenna loses a lot of range.
Is a higher-gain antenna always better?
Not always. High gain narrows the vertical beam, which suits towers but not hilly areas.
How do I get more range from LoRa?
Mount the antenna high and clear, use a tuned antenna, and lower the data rate.
Can I power the module without the antenna?
Avoid it, because transmitting into no antenna can damage the RF chip.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
