Concept explainer · Intermediate · 3 min read
Choosing an Antenna
dBi Gain, VSWR, Connectors and Placement for Wi-Fi, LoRa, 4G and GPS
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Pick an antenna for the exact frequency band, then a connector that fits your module. Higher dBi gain focuses the signal into a flatter beam; it does not add power, and it can reduce coverage above or below the antenna. Check VSWR (aim below 2:1), keep cables short and mount the antenna clear of metal and the ground plane it needs.
Key specs at a glance
- Gain
- Quoted in dBi: 2 to 6 dBi typical for omnis
- Match
- VSWR below 2:1 across the band
- Connectors
- SMA, RP-SMA, U.FL/IPEX, MMCX
- Bands
- 433 MHz, 868/915 MHz, 2.4 GHz, 5.8 GHz, GPS L1, GSM/LTE
- Polarisation
- Linear (most) or circular (FPV, GPS)
- Cable
- Loss rises with length and frequency
Match the band first
An antenna is tuned for a frequency range. A 433 MHz whip on a 2.4 GHz radio wastes most of the power. Use the wavelength tool to see the quarter-wave length for your band: frequency and wavelength and antenna length.
What dBi means
Gain describes how the antenna shapes the signal. A 2.5 dBi 433 MHz folding antenna spreads signal around the horizon; a 6 dBi 2.4 GHz antenna sends it in a flatter doughnut with less above and below. Choose a lower gain when the device moves or tilts, and higher gain for fixed links on a level plane. Convert with the dB converter.
VSWR and matching
VSWR shows how well the antenna matches the radio. 1:1 is perfect; below about 2:1 is fine for most uses. Poor VSWR reflects power back to the transmitter, which wastes range and can heat or damage the output stage. Metal nearby, a short ground plane or a wrong band can ruin the match. A cheap VSWR/NanoVNA check on key antennas is worth it.
Connectors
Check gender and pin: SMA male vs female, SMA vs RP-SMA (the centre pin is swapped), and the tiny U.FL/IPEX connector used on boards and pigtails. See RF antenna connectors and RF cables and pigtails. U.FL connectors are rated for only a few mating cycles, so avoid repeated plugging.
By application
Match the antenna to the job.
| Use | Antenna | Notes |
|---|---|---|
| 433 MHz remote and telemetry | Folding or helical omni | See telemetry radios |
| LoRa 868/915 | Stub or fibreglass omni | See LoRaWAN |
| Wi-Fi/Bluetooth 2.4 GHz | Dipole or PCB antenna | Keep clear of metal |
| 5.8 GHz FPV | Cloverleaf or patch | See FPV antennas |
| GPS L1 | Active ceramic patch with SMA cable | Needs a sky view and 3 V bias |
| GSM/4G | Wideband stub or panel | Check LTE bands for your operator |
- 433 MHz remote and telemetry
- Antenna:
- Folding or helical omni
- Notes:
- See telemetry radios
- LoRa 868/915
- Antenna:
- Stub or fibreglass omni
- Notes:
- See LoRaWAN
- Wi-Fi/Bluetooth 2.4 GHz
- Antenna:
- Dipole or PCB antenna
- Notes:
- Keep clear of metal
- 5.8 GHz FPV
- Antenna:
- Cloverleaf or patch
- Notes:
- See FPV antennas
- GPS L1
- Antenna:
- Active ceramic patch with SMA cable
- Notes:
- Needs a sky view and 3 V bias
- GSM/4G
- Antenna:
- Wideband stub or panel
- Notes:
- Check LTE bands for your operator
Placement tips
- 1Mount the antenna vertically for vertical-polarised radios.
- 2Keep it away from metal enclosures and batteries.
- 3Use a ground plane when the datasheet requires one.
- 4Keep the feed cable short; every metre adds loss at high frequency.
- 5Put GPS antennas on top of the device with a clear sky view.
Try it: Antenna length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Choosing an antenna for the wrong frequency.
- Assuming more dBi always means more range.
- Mixing SMA and RP-SMA connectors.
- Using a long thin coax at 2.4 GHz or higher.
- Mounting the antenna inside a metal box.
Frequently asked questions
Does higher gain mean more range?
Only in the direction the beam points. It changes the pattern, not the power.
What VSWR is acceptable?
Below about 2:1.
What is the difference between SMA and RP-SMA?
RP-SMA swaps the centre contact, so they do not mate.
Can I use any GPS antenna?
It must be for the GPS L1 band and match the module's bias voltage.
Do I need an antenna for a Wi-Fi module with a PCB trace?
No, but an external one improves range.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 57 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






