Component guide · Intermediate · 3 min read
CC1101 and Sub-GHz Transceivers
433, 868 and 915 MHz Modules with Arduino and ESP32
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The CC1101 is a sub-GHz radio chip with SPI control, several modulations and good sensitivity. Modules come for 433, 868 or 915 MHz, so choose the band allowed in your country and pair it with a matching antenna. Wire SPI at 3.3 V, use a library, set frequency, data rate and power, and keep packets short. It is a good low-cost choice for sensor links and remote controls.
Key specs at a glance
- Chip
- TI CC1101 (also Si4432 and similar)
- Bands
- 315, 433, 868, 915 MHz variants
- Modulation
- 2-FSK, GFSK, MSK, OOK/ASK
- Interface
- SPI plus GDO pins; 3.3 V only
- Power
- Up to about 10 to 20 dBm on module versions
- Alternatives
- nRF24L01 (2.4 GHz), LoRa (longer range), Zigbee modules
Which module
Match the frequency to your country and application.
| Module | Band | Notes |
|---|---|---|
| EByte E07-433M20S | 433 MHz | Higher power version, SMA or IPEX antenna |
| EByte E07-900M10S | 855-925 MHz | Sub-1 GHz module |
| CC1101 868 MHz module | 868 MHz | Common in Europe |
| EByte E01 nRF24L01 modules | 2.4 GHz | Different chip, short range |
| EByte E18 Zigbee modules | 2.4 GHz | For Zigbee networks; see Zigbee and XBee |
- EByte E07-433M20S
- Band:
- 433 MHz
- Notes:
- Higher power version, SMA or IPEX antenna
- EByte E07-900M10S
- Band:
- 855-925 MHz
- Notes:
- Sub-1 GHz module
- CC1101 868 MHz module
- Band:
- 868 MHz
- Notes:
- Common in Europe
- EByte E01 nRF24L01 modules
- Band:
- 2.4 GHz
- Notes:
- Different chip, short range
- EByte E18 Zigbee modules
- Band:
- 2.4 GHz
- Notes:
- For Zigbee networks; see Zigbee and XBee
Wiring
Connect VCC (3.3 V), GND, SCK, MISO, MOSI and CSN to the SPI pins of your board, and GDO0 to an interrupt pin. Do not use 5 V logic; use a level shifter for 5 V Arduinos (see logic-level shifting). Keep the antenna connected whenever you transmit. Use short SPI wires; see SPI.
Software and settings
Use a library such as ELECHOUSE CC1101 or RadioLib. Set the frequency, data rate, modulation and output power, then send packets with addressing and a CRC. Lower data rates give more range. Compare with other radios in choosing a wireless module, 433 MHz RF and LoRa.
Regional rules and security
Frequency and power limits differ by country, so use only the band you may use and stay within the legal power. Do not clone or replay other people's remote controls, alarm systems or car keys. For your own devices, use encryption or rolling codes if the data matters.
Range tips
- Use a tuned antenna for the band; see antenna length.
- Mount the antenna away from metal.
- Keep a clean 3.3 V supply with a capacitor near the module.
- Test with a low data rate first, then increase.
- Use acknowledgements so you know a packet arrived.
Try it: Antenna length calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Using 5 V on a 3.3 V module.
- Running the transmitter without an antenna.
- Choosing the wrong band for your country.
- Using a data rate too high for the range.
- Replaying third-party remote signals.
Frequently asked questions
CC1101 or LoRa?
LoRa has longer range at low data rates. CC1101 is simpler and cheaper for short links.
Which band for India?
868 MHz modules and 865 to 867 MHz settings are the usual choice; check current rules.
Does the CC1101 need a level shifter?
Yes on 5 V boards.
Can I use it as a remote control receiver?
For your own remotes, yes, with matching modulation.
What is OOK?
On-off keying, a simple modulation used by cheap remotes.
Parts for this guide
Calculators
Terms in this guide
Projects that use it
Put this into practice: 3 step-by-step builds in our project library use parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.






