Component guide · Intermediate · 5 min read
Multi-Band and 2.4 GHz LoRa Modules

EByte E80 LR1121, Seeed Wio-LR1121, Waveshare Core2021 LR2021 and ESP32-S3 LR1121 Boards, G-NiceRF SX1280 LoRa1280F27 and LoRa128X-T, Elecrow nRF52840 LR1110/LR1121/SX1262/LLCC68 Modules, Wio-WM1110 and ThinkNode M7 Meshtastic Gateway
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are the newer LoRa radios. LR1121 covers both sub-GHz (433 and 865 MHz) and 2.4 GHz in one chip. LR1110 adds GNSS and Wi-Fi scanning for low-power tracking. LR2021 is Semtech's latest high data rate chip. SX1280 works only at 2.4 GHz, which is licence-free worldwide and allows faster data and ranging. Elecrow and Seeed modules pair these radios with an nRF52840 for BLE, and ThinkNode M7 is a Meshtastic gateway.
Key specs at a glance
- LR1121
- Sub-GHz 150-960 MHz plus 2.4 GHz and S-band LoRa
- LR1110
- Sub-GHz LoRa plus GNSS and Wi-Fi passive scan
- LR2021
- Newest Semtech transceiver, LoRa and FSK, higher data rates
- SX1280
- 2.4 GHz LoRa, FLRC and ranging; 500 mW on LoRa1280F27
- Host
- SPI to any MCU; nRF52840 or ESP32-S3 on combo boards
- Uses
- LoRaWAN, Meshtastic, long-range RC links, asset tracking
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1EByte E80-400M2213S LR1121 Dual-Band LoRa Module 433/868/915/2.4G SPI₹909
Option 2EByte E80-900M2213S LR1121 LoRa Dual-Band SPI RF Transceiver Module₹879
Option 3Seeed Studio Wio-LR1121 Wireless LoRa Module w/ IPEX₹1,079
Option 4Waveshare Core2021-HF Dual-Band LoRa Module LR2021 Transceiver₹1,399
Option 5Waveshare Core2021-LF Dual-Band LoRa Module, LR2021 Transceiver 410-510MHz₹1,399
Option 6Waveshare ESP32-S3 LoRa Development Board w/ LR1121 RF Chip HF Version₹1,809
What the Multi-band and 2.4 GHz LoRa: LR1121, LR1110, LR2021 and SX1280 modules, Wio-WM1110, Elecrow nRF modules and ThinkNode M7 is
LR1121, LR2021 and SX1280 LoRa modules from Semtech add multi-band LoRa: the SX1280 runs LoRa at 2.4 GHz, and the LR1121 and LR2021 cover sub-GHz and 2.4 GHz in one chip.
Choose by band and job. For LoRaWAN in India use the sub-GHz side on IN865. Use 2.4 GHz (SX1280, or LR1121's high band) for worldwide licence-free links and faster data, accepting shorter range than sub-GHz. For trackers, LR1110 lets a cloud solver locate the device from a short GNSS or Wi-Fi scan at very low power.
These chips are not register-compatible with the SX127x, so old LoRa.h sketches will not work. Use RadioLib, which supports SX1280, LR1110 and LR1121, or the maker's SDK. Fit an antenna for each band you use; dual-band modules often have two antenna ports.
Multi-band and 2.4 GHz LoRa: LR1121, LR1110, LR2021 and SX1280 modules, Wio-WM1110, Elecrow nRF modules and ThinkNode M7 pinout
The pins on the Multi-band and 2.4 GHz LoRa: LR1121, LR1110, LR2021 and SX1280 modules, Wio-WM1110, Elecrow nRF modules and ThinkNode M7 and what each one does.
| Pin | Function |
|---|---|
| NSS | SPI chip select |
| SCK / MOSI / MISO | SPI bus |
| BUSY | Radio busy flag; must be read on LR11xx and SX128x |
| DIO1 / IRQ | Interrupt for TX done and RX done |
| NRESET | Reset |
| ANT LF / ANT HF | Separate sub-GHz and 2.4 GHz antenna ports on dual-band modules |
- NSS
- SPI chip select
- SCK / MOSI / MISO
- SPI bus
- BUSY
- Radio busy flag; must be read on LR11xx and SX128x
- DIO1 / IRQ
- Interrupt for TX done and RX done
- NRESET
- Reset
- ANT LF / ANT HF
- Separate sub-GHz and 2.4 GHz antenna ports on dual-band modules
Wiring the Multi-band and 2.4 GHz LoRa: LR1121, LR1110, LR2021 and SX1280 modules, Wio-WM1110, Elecrow nRF modules and ThinkNode M7
Never transmit without antennas on the ports you use, and power the 500 mW SX1280 module from a supply that can handle the TX current.
| Multi-band and 2.4 GHz LoRa: LR1121, LR1110, LR2021 and SX1280 modules, Wio-WM1110, Elecrow nRF modules and ThinkNode M7 pin | Connection | Note |
|---|---|---|
| NSS, SCK, MOSI, MISO | MCU SPI | 3.3 V only |
| BUSY | MCU input | Required |
| DIO1 | MCU interrupt pin | RX and TX done |
| VCC | 3.3 V, 500 mA+ for 500 mW modules | Add a bulk capacitor |
| Antennas | LF and HF ports | One per band used |
- NSS, SCK, MOSI, MISO
- Connection:
- MCU SPI
- Note:
- 3.3 V only
- BUSY
- Connection:
- MCU input
- Note:
- Required
- DIO1
- Connection:
- MCU interrupt pin
- Note:
- RX and TX done
- VCC
- Connection:
- 3.3 V, 500 mA+ for 500 mW modules
- Note:
- Add a bulk capacitor
- Antennas
- Connection:
- LF and HF ports
- Note:
- One per band used
Example code
For 2.4 GHz on the LR1121 use a frequency such as 2450.0 and its own power limits; for SX1280 use the SX1280 class instead. Check the RadioLib examples for your RadioLib version.
#include <RadioLib.h>
// NSS, IRQ (DIO9 on LR11xx), RESET, BUSY
LR1121 radio = new Module(10, 2, 9, 3);
void setup() {
Serial.begin(115200);
// 865 MHz, 125 kHz BW, SF9, CR 4/7, sync word, 14 dBm
int state = radio.begin(865.0, 125.0, 9, 7, RADIOLIB_LR11X0_LORA_SYNC_WORD_PRIVATE, 14);
if (state != RADIOLIB_ERR_NONE) {
Serial.print("Init failed, code ");
Serial.println(state);
while (true);
}
}
void loop() {
int state = radio.transmit("Hello from Geekobot");
Serial.println(state == RADIOLIB_ERR_NONE ? "Sent" : "TX error");
delay(5000);
}Setup and tuning
connect SPI (SCK, MISO, MOSI, NSS), BUSY, RESET and DIO pins at 3.3 V.
use RadioLib, which supports SX1280, LR1121 and newer Semtech chips.
fit the right antenna for each band; dual-band chips need two or a dual-band antenna.
match frequency, bandwidth, spreading factor and coding rate on both ends.
use only the bands and power allowed in your country.
What you need
Shop this list15 of 15 found in our store · ₹26,381
EByte E80-400M2213S LR1121 Dual-Band LoRa Module 433/868/915/2.4G SPI: the part this guide coversEByte E80-400M2213S LR1121 Dual-Band LoRa Module 433/868/915/2.4G SPI₹909
EByte E80-900M2213S LR1121 LoRa Dual-Band SPI RF Transceiver Module: another version this guide coversEByte E80-900M2213S LR1121 LoRa Dual-Band SPI RF Transceiver Module₹879
Seeed Studio Studio Wio-LR1121 Wireless LoRa Module w/ IPEX: another version this guide coversSeeed Studio Wio-LR1121 Wireless LoRa Module w/ IPEX₹1,079Closest match, check the specs
Waveshare Core2021-HF Dual-Band LoRa Module LR2021 Transceiver: another version this guide coversWaveshare Core2021-HF Dual-Band LoRa Module LR2021 Transceiver₹1,399
Waveshare Core2021-LF Dual-Band LoRa Module, LR2021 Transceiver 410-510MHz: another version this guide coversWaveshare Core2021-LF Dual-Band LoRa Module, LR2021 Transceiver 410-510MHz₹1,399
Waveshare ESP32-S3 LoRa Development Board w/ LR1121 RF Chip HF Version: another version this guide coversWaveshare ESP32-S3 LoRa Development Board w/ LR1121 RF Chip HF Version₹1,809
Waveshare ESP32-S3 LoRa Development Board w/ LR1121 RF Chip LF Version: another version this guide coversWaveshare ESP32-S3 LoRa Development Board w/ LR1121 RF Chip LF Version₹1,809
G-NiceRF LoRa1280F27 SX1280 500mW 2.4GHz LoRa Module: another version this guide coversG-NiceRF LoRa1280F27 SX1280 500mW 2.4GHz LoRa Module₹1,429
G-NiceRF LoRa128X-T SX1280/SX1281 2.4GHz LoRa Module w/ TCXO: another version this guide coversG-NiceRF LoRa128X-T SX1280/SX1281 2.4GHz LoRa Module w/ TCXO₹929
Elecrow nRFLR1110 Wireless Transceiver Module w/ nRF52840 & LR1110: another version this guide coversElecrow nRFLR1110 Wireless Transceiver Module w/ nRF52840 & LR1110₹1,379
Elecrow nRFLR1121 Wireless Transceiver Module w/ nRF52840 & SX1121: another version this guide coversElecrow nRFLR1121 Wireless Transceiver Module w/ nRF52840 & SX1121₹1,609
Elecrow nRFLR1262 Wireless Transceiver Module – nRF52840 & SX1262: another version this guide coversElecrow nRFLR1262 Wireless Transceiver Module – nRF52840 & SX1262₹1,349
Elecrow nRFLRCC68 Wireless Transceiver Module w/ nRF52840 & LLCC68: another version this guide coversElecrow nRFLRCC68 Wireless Transceiver Module w/ nRF52840 & LLCC68₹819
Seeed Wio-WM1110 Dev Kit (Semtech LR1110 + Nordic nRF52840): another version this guide coversSeeed Wio-WM1110 Dev Kit (Semtech LR1110 + Nordic nRF52840)₹3,799
Elecrow ThinkNode M7 Meshtastic Gateway (ESP32-S3, LR1110, PoE): another version this guide coversElecrow ThinkNode M7 Meshtastic Gateway (ESP32-S3, LR1110, PoE)₹5,785
Alternatives and when to choose them
- SX1262 LoRa module: the popular sub-GHz radio.
- EByte E220 LLCC68: UART LoRa module.
- LoRaWAN nodes and gateways: network side.
- LoRa antennas: antennas for each band.
Common mistakes to avoid
- Using 5 V logic.
- Forgetting the BUSY pin.
- Mismatched radio settings.
- Transmitting without an antenna.
Frequently asked questions
Why choose an SX1280 for LoRa?
It runs at 2.4 GHz, allowed worldwide, and supports ranging; range is shorter than sub-GHz.
Can the LR1121 do sub-GHz and 2.4 GHz?
Yes. It covers both and is used in ExpressLRS dual-band receivers.
Which Arduino library supports these chips?
RadioLib supports the SX1280 and the LR11xx family on Arduino, ESP32 and Pico.
Why do two modules not talk?
Frequency, bandwidth, spreading factor or sync word do not match.
Are these modules 5 V tolerant?
No. These radios run at 3.3 V, so use level shifting with 5 V boards.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
