Component guide · Intermediate · 3 min read
Mains Step-Down Transformers for DC Power Supplies
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A step-down transformer converts 230 V AC mains to a lower AC voltage such as 12 V, with the secondary electrically isolated from the mains. Add a bridge rectifier and a smoothing capacitor to get DC of about 1.4 times the AC rating minus about 1.4 V, then a regulator for a steady output. Transformers are heavy and less efficient than SMPS modules but quiet and robust.
Key specs at a glance
- Primary
- 230 V AC, 50 Hz in India
- Secondary
- e.g. 9 V, 12 V or 12-0-12 V (centre-tapped)
- Rating
- VA (volt-amps) or secondary current
- DC after bridge + cap
- About 1.41 × Vrms − 1.4 V; higher with no load
- Isolation
- Secondary is isolated from mains
- Protection
- Fuse on the primary side
This part is often wired to 230 V mains. Do all wiring with the plug pulled out, keep mains wires inside a closed box with strain relief, add a fuse, and never touch the board while it is plugged in. If you are new to mains wiring, have an electrician check it before you switch on.
Building a linear DC supply
- 1Transformer secondary to a bridge rectifier.
- 2A large electrolytic capacitor across the rectifier output, about 1000 to 2200 µF per amp, rated well above the peak voltage.
- 3A regulator such as a 7805 or LM317, with its heatsink.
Example: a 12 V transformer gives about 12 × 1.41 − 1.4 ≈ 15.5 V DC at full load and more at light load, which feeds a 12 V or lower regulator nicely. Ripple rises with current, so size the smoothing capacitor for the load (see capacitors).
Choosing one
at least 3 V above your regulated output after rectification.
the DC current you need × about 1.6 for a bridge and capacitor supply, because capacitor charging current is peaky.
a 12-0-12 V transformer gives +12 V and −12 V rails for op-amps, or a full-wave supply with two diodes.
for more than a few amps, or where size and efficiency matter, a switching supply is lighter and cooler.
Mains safety
Mains wiring can kill. Use a fused, switched inlet; enclose all mains connections; earth metal cases; insulate primary terminals with heat shrink; and keep mains and low-voltage wiring apart. Fuse the primary at a value suited to the transformer's VA rating. If you are not trained, use a ready-made, certified adapter instead.
Try it: Linear regulator heat calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- No fuse on the primary.
- Exposed mains terminals.
- Undersized capacitor causing heavy ripple.
- Forgetting the 1.41 × factor and overloading a regulator with too much voltage.
- Using a transformer far below the needed VA rating.
Frequently asked questions
What DC voltage do I get from a 12 V transformer?
About 15 to 17 V after a bridge rectifier and capacitor, depending on load.
What does VA mean on a transformer?
Volt-amps: the secondary voltage times its maximum current. A 12 V 24 VA transformer supplies 2 A AC.
Transformer or SMPS?
SMPS for efficiency, size and high current. Transformers for low noise and simplicity.
What is a centre-tapped transformer?
One with a connection in the middle of the secondary, giving two equal voltages for dual or full-wave supplies.
Why does my transformer get hot?
It is overloaded or the rectifier capacitor draws high peak currents. Use a larger VA rating.
Parts for this guide
- ₹86View
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
