Component guide · Intermediate · 3 min read
MAX6501 and MAX6509 Temperature Switch ICs

Fixed and Resistor-Set Trip Points
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A temperature switch IC flips its output when the chip passes a set temperature, with no microcontroller needed. The MAX6501 has a factory trip point printed in its part number (P045 is 45 degrees C, P125 is 125 degrees C) and an open-drain output. The MAX6509 sets the trip point with one external resistor. Use them for fan control and thermal shutdown.
Key specs at a glance
- Supply
- 2.7 to 5.5 V
- Trip point
- Fixed (MAX6501, e.g. 45 or 125 degrees C) or one resistor (MAX6509)
- Accuracy
- About plus or minus 0.5 degrees C typical
- Output
- Open drain, active low
- Hysteresis
- 2 or 10 degrees C (pin selectable)
- Package
- SOT-23-5
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Analog Devices MAX6501UKP125+T Temperature Sensor IC, Open Drain, ±0.5°C, -55°C to 125°C, SOT-23-5₹114
Option 2Analog Devices MAX6501UKP045+T Temperature Sensor IC, Micropower, Open Drain, ±0.5°C, SOT-23-5₹95
Option 3Analog Devices MAX6509HAUK+T Temperature Sensor IC, Programmable, Open Drain, ±0.5°C, SOT-23-5₹99
What the MAX6501 and MAX6509 temperature switch ICs is
The MAX6501 to MAX6509 are temperature switch ICs that change an output when a set temperature is crossed, used for fan control and over-temperature shutdown without a microcontroller.
Hysteresis stops the output chattering at the trip point. Select 10 degrees C for fans so they do not cycle every few seconds.
Because the output is open drain, add a pull-up resistor to the logic or relay supply.
MAX6501 and MAX6509 temperature switch ICs pinout
The pins on the MAX6501 and MAX6509 temperature switch ICs and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| TOVER / OUT | Open-drain output |
| HYST | Hysteresis select |
| SET (MAX6509) | Trip resistor to GND |
- VCC
- Supply
- GND
- Ground
- TOVER / OUT
- Open-drain output
- HYST
- Hysteresis select
- SET (MAX6509)
- Trip resistor to GND
Wiring the MAX6501 and MAX6509 temperature switch ICs
To drive a fan directly, connect OUT to a MOSFET gate with a pull-up so the fan runs when hot.
| MAX6501 and MAX6509 temperature switch ICs pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 3.3 V |
| GND | GND | GND |
| OUT | D2 with 10 k pull-up | GPIO 27 with 10 k pull-up |
| HYST | GND or VCC | GND or VCC |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 3.3 V
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- OUT
- Arduino Uno:
- D2 with 10 k pull-up
- ESP32:
- GPIO 27 with 10 k pull-up
- HYST
- Arduino Uno:
- GND or VCC
- ESP32:
- GND or VCC
Example code
A minimal sketch to check the part works.
const int OVER = 2; // open drain, low when over temperature
void setup() { Serial.begin(115200); pinMode(OVER, INPUT_PULLUP); }
void loop() {
if (digitalRead(OVER) == LOW) Serial.println("Over temperature");
delay(500);
}Setup and tuning
MAX6501 to MAX6504 have factory set points; MAX6509 sets the trip point with one resistor.
check whether your part is open drain or push-pull, and active high or low.
add a pull-up resistor on open-drain outputs.
select 2 °C or 10 °C hysteresis with the HYST pin where available.
mount close to the heat source being monitored.
What you need
Shop this list6 of 7 found in our store · ₹757
Analog Devices MAX6501UKP125+T Temperature Sensor IC, Open Drain, ±0.5°C, -55°C to 125°C, SOT-23-5: the part this guide coversAnalog Devices MAX6501UKP125+T Temperature Sensor IC, Open Drain, ±0.5°C, -55°C to 125°C, SOT-23-5₹114
Analog Devices MAX6501UKP045+T Temperature Sensor IC, Micropower, Open Drain, ±0.5°C, SOT-23-5: another version this guide coversAnalog Devices MAX6501UKP045+T Temperature Sensor IC, Micropower, Open Drain, ±0.5°C, SOT-23-5₹95
Analog Devices MAX6509HAUK+T Temperature Sensor IC, Programmable, Open Drain, ±0.5°C, SOT-23-5: another version this guide coversAnalog Devices MAX6509HAUK+T Temperature Sensor IC, Programmable, Open Drain, ±0.5°C, SOT-23-5₹99- Uno R3 development board: the controller used in the wiring tableFind this part
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
Resistor assortment kit (30 values): pull-up and divider resistorsResistor Assortment Kit (30 Values)₹33
Buzzer module 3.3-5 V: for an audible alarmBuzzer Module 3.3–5V₹27
Alternatives and when to choose them
- LM75 family: programmable OS output over I2C.
- Bimetal thermostat switches: mechanical cut-outs for mains.
- W1209 and XH-W3001 modules: ready thermostat boards.
Common mistakes to avoid
- Leaving out the pull-up on open-drain.
- Choosing the wrong set-point version.
- Small hysteresis causing chatter.
- Mounting far from the heat source.
Frequently asked questions
How does a temperature switch IC work?
It changes its output when the temperature passes a trip point.
How do I set the MAX6509 trip point?
Pick the external resistor value from the datasheet formula for the temperature you want.
Do I need a microcontroller?
No. It can drive a fan MOSFET or shutdown pin directly.
Why does the fan cycle on and off quickly?
The hysteresis is too small; select the larger hysteresis option on the HYST pin.
Is it accurate?
Typically about ±0.5 to ±4 °C depending on the part.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

