Concept explainer · Intermediate · 3 min read
PCB Basics

Designing and Ordering Your First Board
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
A printed circuit board (PCB) replaces wires with copper traces on a fibreglass board. You draw the schematic, assign each part a footprint, lay out the board and route traces in free software such as KiCad or EasyEDA, check the design rules, then export Gerber files and upload them to a PCB maker. A simple two-layer board usually arrives in about a week, often cheaper than the parts on it.
Key specs at a glance
- Standard board
- FR-4, 1.6 mm thick, 2 layers, 1 oz (35 µm) copper
- Minimum trace/space
- Commonly 0.15 to 0.2 mm (6 to 8 mil) at budget makers
- Signal traces
- 0.25 to 0.3 mm typical
- Power traces
- Size by current: about 1 mm for 2 A on outer 1 oz copper
- Output files
- Gerbers + drill file (+ BOM and pick-and-place for assembly)
- Free tools
- KiCad, EasyEDA
What a PCB is made of
| Feature | What it is |
|---|---|
| Substrate | Fibreglass FR-4 board, usually 1.6 mm |
| Copper layers | Usually 2 (top and bottom); 4+ for dense or high-speed designs |
| Traces | Copper paths that replace wires |
| Pads and footprints | Copper areas where part pins are soldered |
| Vias | Plated holes that join layers |
| Solder mask | The green (or other colour) coating that stops solder bridging |
| Silkscreen | Printed labels: R1, C3, pin names, your logo |
| Copper pour | Large filled areas, usually ground, for low noise and heat spreading |
- Substrate
- Fibreglass FR-4 board, usually 1.6 mm
- Copper layers
- Usually 2 (top and bottom); 4+ for dense or high-speed designs
- Traces
- Copper paths that replace wires
- Pads and footprints
- Copper areas where part pins are soldered
- Vias
- Plated holes that join layers
- Solder mask
- The green (or other colour) coating that stops solder bridging
- Silkscreen
- Printed labels: R1, C3, pin names, your logo
- Copper pour
- Large filled areas, usually ground, for low noise and heat spreading
The design workflow
- 1Schematic: draw the circuit with symbols from the library. See schematic symbols.
- 2Footprints: assign each symbol its physical footprint (for example a 0805 resistor or a 2.54 mm header).
- 3Board outline: set the size and mounting holes.
- 4Place parts: connectors on edges, decoupling capacitors next to chip power pins, crystals close to the microcontroller.
- 5Route traces: power and ground first, wide; then signals. Add a ground pour on both layers and stitch them with vias.
- 6Design rule check (DRC): load your maker's rules (minimum trace, spacing, drill sizes) and fix every error.
- 7Export Gerbers and drill files, check them in a Gerber viewer, then upload and order.
Rules of thumb for a first board
- Keep the design two-layer, through-hole or large SMD (0805 or 1206) parts for easy hand soldering.
- Size power traces with the PCB trace width calculator; 1 mm handles about 2 A on outer 1 oz copper with modest heating.
- Put a 100 nF decoupling capacitor at every IC's power pin.
- Leave at least 3 mm clearance from mounting holes and board edges.
- Add test points and label every connector pin on the silkscreen.
- Keep mains voltage off hobby PCBs unless you understand creepage and clearance rules.
Ordering and assembly
Most hobby PCB makers take a zip of Gerbers, show a preview and quote by size, layers, quantity and colour. Standard options (green, 1.6 mm, HASL finish) are cheapest and fastest. Many offer assembly of SMD parts from their stock, which needs a BOM and a component placement (CPL) file. Before ordering 100 boards, order five, build one and test it.
Try it: PCB trace width calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Skipping the design rule check.
- Footprint mismatch: the part on the schematic is not the part you bought.
- Thin power traces that heat up.
- No decoupling capacitors near chips.
- Forgetting mounting holes or putting connectors in the middle of the board.
Frequently asked questions
What software should I use to design a PCB?
KiCad (free, open source and powerful) or EasyEDA (free, browser-based and linked to a PCB maker's parts library) are the usual choices.
What are Gerber files?
The standard manufacturing files describing each copper, mask and silkscreen layer, plus a drill file for holes. PCB makers build boards from them.
How wide should my PCB traces be?
About 0.25 mm for signals. For power, size by current: roughly 1 mm for 2 A on outer 1 oz copper. Use a trace width calculator.
How much does a hobby PCB cost?
Five small two-layer boards often cost only a few hundred rupees plus shipping, depending on size and options.
Two layers or four?
Two layers suit most hobby boards. Four layers help with dense designs, high-speed signals and noise, at higher cost.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
- IPC-2221 generic standard on printed board design (trace width guidance)
- KiCad documentation
- Gerber format specification (Ucamco)
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




