How-to · Beginner · 3 min read
Perfboard and Stripboard
Moving a Circuit Off the Breadboard
By Geekobot Learning Team · Updated 24 Oct 2026
On this page
Perfboard (zero PCB) is a board of holes with separate copper pads that you join with solder bridges or wire; stripboard has rows of copper strips that you cut where needed. Both let you make a permanent version of a breadboard circuit. Plan the layout on paper first, use sockets for chips and plug-in modules, run power and ground rails along the edges, and check every joint with a multimeter before powering up.
Key specs at a glance
- Pitch
- 2.54 mm, fits DIP chips and headers
- Perfboard
- Isolated pads; connections by wire or solder bridges
- Stripboard
- Copper strips; cut with a 3.5 mm drill bit or track cutter
- Material
- FR-4 (fibreglass, strong) or phenolic (cheaper, brittle)
- Tools
- Soldering iron, solder, wire, flush cutters, multimeter
- Next step
- A custom PCB for repeat builds
Perfboard or stripboard?
| Perfboard (zero PCB) | Stripboard (Veroboard) | |
|---|---|---|
| Copper | Separate pad per hole | Long strips |
| Wiring | Every connection made by you | Strips connect rows; you cut breaks |
| Planning | Freeform | Needs a layout plan |
| Good for | Module-based builds (ESP32 + sensor boards) | Circuits with many discrete parts in rows |
| Common mistake | Messy wiring underneath | Forgetting to cut a track under a chip |
- Copper
- Perfboard (zero PCB):
- Separate pad per hole
- Stripboard (Veroboard):
- Long strips
- Wiring
- Perfboard (zero PCB):
- Every connection made by you
- Stripboard (Veroboard):
- Strips connect rows; you cut breaks
- Planning
- Perfboard (zero PCB):
- Freeform
- Stripboard (Veroboard):
- Needs a layout plan
- Good for
- Perfboard (zero PCB):
- Module-based builds (ESP32 + sensor boards)
- Stripboard (Veroboard):
- Circuits with many discrete parts in rows
- Common mistake
- Perfboard (zero PCB):
- Messy wiring underneath
- Stripboard (Veroboard):
- Forgetting to cut a track under a chip
From breadboard to perfboard in six steps
- 1Draw the circuit as a simple schematic and mark which parts connect.
- 2Plan the layout on squared paper or a free tool (such as DIY Layout Creator or Fritzing's stripboard view). Put power input at one edge and connectors at the edges.
- 3Place sockets first: female headers for modules such as an ESP32 or Nano, and DIP sockets for chips, so they can be replaced.
- 4Solder low parts first (resistors, diodes), then taller ones (capacitors, headers, terminal blocks).
- 5Wire power and ground rails with thicker bare wire along the board edges; then add signal wires, using different colours.
- 6Test before power: check for shorts between power and ground with a multimeter's continuity mode, then power up with a current-limited supply if you have one.
Neat and reliable builds
- Use solid-core 22 to 24 AWG wire or the cut legs of resistors for short links.
- On stripboard, cut tracks under DIP chips between the two rows of pins.
- Leave mounting holes in the corners and use standoffs.
- Hot glue or cable ties keep off-board wires from pulling on joints.
- Label connectors with a marker. Your future self will thank you.
When to move to a real PCB
If you will build more than a couple of copies, have dense wiring or need high current, a custom PCB is faster and more reliable. Hobby PCB services make five boards for a small fee in about a week. See PCB basics.
Try it: PCB trace width calculator (IPC-2221)
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Soldering modules directly with no sockets.
- Forgetting to cut stripboard tracks under a chip.
- No continuity check for shorts before power-up.
- Thin wire for power rails.
- Placing power and signal connectors in random spots, making the board hard to mount.
Frequently asked questions
What is a zero PCB?
The common Indian name for perfboard: a board with a grid of holes and separate copper pads for soldering a permanent circuit.
Is stripboard better than perfboard?
Stripboard needs less wiring for circuits laid out in rows; perfboard is more flexible for module-based builds. Both work well.
How do I cut stripboard tracks?
Twist a 3.5 mm drill bit or a track-cutting tool by hand in the hole until the copper is fully removed, then check with a multimeter.
Should I solder an Arduino Nano directly to perfboard?
It is better to solder female headers and plug the Nano in, so you can replace or reuse it.
When should I order a PCB instead?
When you need several copies, a compact layout, high current or a professional finish.
Parts for this guide
Terms in this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
- IPC hand-soldering workmanship guidance (IPC-A-610 overview)
- Common prototyping board manufacturer specifications
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




