Component guide · Intermediate · 5 min read
Raspberry Pi Cellular HATs

SIM7600 4G, SIM7670G and A7670E Cat-1, Quectel EC200, Teltonika 4G and 5G, Waveshare 5G, NB-IoT and GSM
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
A cellular HAT puts a mobile modem on a Raspberry Pi so it can get internet, send SMS or report its GPS position anywhere with phone signal. SIM7600 boards are Cat-4 4G with GNSS; SIM7670G, A7670E and EC200 are cheaper Cat-1 4G; the Teltonika and Waveshare 5G boards are for high-speed links; NB-IoT and GSM boards suit tiny sensor messages.
Key specs at a glance
- Networks
- 5G, 4G Cat-4, Cat-1, Cat-M / NB-IoT, 2G GSM
- Speed
- From a few kbit/s (NB-IoT) to over 1 Gbit/s (5G)
- Interface
- USB (via pogo pins or cable) and UART
- GNSS
- Built into SIM7600, SIM7670G, A7672, EC200 GNSS versions
- SIM
- Nano or micro SIM; some have eSIM
- Antennas
- u.FL or SMA, main plus diversity
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare SIM7600G-H 4G HAT for Raspberry Pi₹10,219
Option 2Waveshare SIM7600G-H 4G HAT (B) for Raspberry Pi LTE Cat-4₹9,799
Option 3Waveshare SIM7600E-H 4G HAT for Raspberry Pi₹12,100
Option 4Waveshare SIM7600G-H 4G M.2 HAT for Raspberry Pi, LTE Cat4 GNSS₹7,769
Option 5Waveshare SIM7670G Cat-1/GNSS HAT for Raspberry Pi₹5,323
Option 6Waveshare A7670E Cat-1 GSM GPRS GNSS HAT for Raspberry Pi₹3,499
What the Raspberry Pi 4G, 5G and NB-IoT cellular HATs is
Raspberry Pi 4G and 5G cellular HATs use modems like the SIM7600, EC25 or RM500Q to give a Pi mobile internet, SMS and GPS where there is no Wi-Fi.
Most 4G and 5G HATs connect over USB and appear as a network interface (RNDIS, ECM or QMI), so the Pi gets internet like on Wi-Fi. Use the UART or /dev/ttyUSB2 port for AT commands and SMS.
In India use a SIM that supports the module's LTE bands (B1, B3, B5, B8, B40, B41). Pure 2G GSM boards may not work where 2G is being switched off.
Raspberry Pi 4G, 5G and NB-IoT cellular HATs pinout
The pins on the Raspberry Pi 4G, 5G and NB-IoT cellular HATs and what each one does.
| Pin | Function |
|---|---|
| USB (pogo or cable) | Main data link for internet |
| UART TX/RX | GPIO14/15 for AT commands on many boards |
| PWRKEY | GPIO pin that switches the modem on |
| SIM slot | Nano or micro SIM |
| MAIN / DIV / GNSS antennas | Connect all antennas before powering on |
- USB (pogo or cable)
- Main data link for internet
- UART TX/RX
- GPIO14/15 for AT commands on many boards
- PWRKEY
- GPIO pin that switches the modem on
- SIM slot
- Nano or micro SIM
- MAIN / DIV / GNSS antennas
- Connect all antennas before powering on
Wiring the Raspberry Pi 4G, 5G and NB-IoT cellular HATs
Fit antennas before switching on; transmitting without an antenna can damage the modem. Use a 3A or better supply, or power the HAT separately.
| Raspberry Pi 4G, 5G and NB-IoT cellular HATs pin | Connection | Note |
|---|---|---|
| Data | USB cable or pogo pins to a Pi USB port | Fit the cable that comes with the HAT |
| AT port | UART on GPIO14/15 | Disable the serial console first |
| Power | Pi 5V, or the HAT's own USB-C | Modems draw 2A peaks |
- Data
- Connection:
- USB cable or pogo pins to a Pi USB port
- Note:
- Fit the cable that comes with the HAT
- AT port
- Connection:
- UART on GPIO14/15
- Note:
- Disable the serial console first
- Power
- Connection:
- Pi 5V, or the HAT's own USB-C
- Note:
- Modems draw 2A peaks
Example code
For internet, most boards come up as usb0 or wwan0. On SIM7600 send AT+CUSBPIDSWITCH=9011,1,1 once to switch to RNDIS mode. Set the APN of your operator with AT+CGDCONT.
import serial, time
m = serial.Serial("/dev/ttyUSB2", 115200, timeout=2)
def at(cmd):
m.write((cmd + "\r").encode())
time.sleep(0.5)
print(m.read(m.in_waiting or 1).decode(errors="ignore"))
at("AT") # OK
at("AT+CSQ") # signal quality, 10+ is usable
at("AT+CREG?") # 0,1 = registered on home network
at("AT+CMGF=1") # text mode SMS
m.write(b'AT+CMGS="+91XXXXXXXXXX"\r'); time.sleep(0.5)
m.write(b"Hello from Raspberry Pi\x1a")Setup and tuning
use a data SIM and set the operator APN.
connect via USB to the Pi and use ModemManager, QMI or the maker's script.
connect main and diversity antennas (and GNSS if used).
5G modems need a strong supply; use the HAT's power input.
check the modem supports your operator's bands.
What you need
Shop this list20 of 20 found in our store · ₹2,01,542
Waveshare SIM7600G-H 4G HAT for Raspberry Pi: the part this guide coversWaveshare SIM7600G-H 4G HAT for Raspberry Pi₹10,219
Waveshare SIM7600G-H 4G HAT (B) for Raspberry Pi LTE Cat-4: another version this guide coversWaveshare SIM7600G-H 4G HAT (B) for Raspberry Pi LTE Cat-4₹9,799
Waveshare SIM7600E-H 4G HAT for Raspberry Pi: another version this guide coversWaveshare SIM7600E-H 4G HAT for Raspberry Pi₹12,100
Waveshare SIM7600G-H 4G M.2 HAT for Raspberry Pi, LTE Cat4 GNSS: another version this guide coversWaveshare SIM7600G-H 4G M.2 HAT for Raspberry Pi, LTE Cat4 GNSS₹7,769
Waveshare SIM7670G Cat-1/GNSS HAT for Raspberry Pi: another version this guide coversWaveshare SIM7670G Cat-1/GNSS HAT for Raspberry Pi₹5,323
Waveshare A7670E Cat-1 GSM GPRS GNSS HAT for Raspberry Pi: another version this guide coversWaveshare A7670E Cat-1 GSM GPRS GNSS HAT for Raspberry Pi₹3,499
SIMCom A7672 4G LTE GNSS Raspberry Pi HAT: another version this guide coversSIMCom A7672 4G LTE GNSS Raspberry Pi HAT₹8,128
SIMCom A7672S 4G LTE Pi HAT for Raspberry Pi: another version this guide coversSIMCom A7672S 4G LTE Pi HAT for Raspberry Pi₹7,079
Quectel EC200 4G LTE eSIM Raspberry Pi HAT: another version this guide coversQuectel EC200 4G LTE eSIM Raspberry Pi HAT₹7,211
WIN PiHAT Quectel EC200 4G LTE Cat 1 GNSS Raspberry Pi HAT: another version this guide coversWIN PiHAT Quectel EC200 4G LTE Cat 1 GNSS Raspberry Pi HAT₹6,948
WIN-PIHAT-QCTL-EC200 4G LTE Cat-1 GNSS Pi HAT: another version this guide coversWIN-PIHAT-QCTL-EC200 4G LTE Cat-1 GNSS Pi HAT₹7,473
Teltonika EBD021 4G Cat 4 LTE HAT for Raspberry Pi: another version this guide coversTeltonika EBD021 4G Cat 4 LTE HAT for Raspberry Pi₹6,109
Teltonika EBD050 5G HAT for Raspberry Pi 4/5: another version this guide coversTeltonika EBD050 5G HAT for Raspberry Pi 4/5₹44,299
Teltonika EBD070 5G RedCap Raspberry Pi HAT: another version this guide coversTeltonika EBD070 5G RedCap Raspberry Pi HAT₹25,209
Waveshare 5G HAT for Raspberry Pi: another version this guide coversWaveshare 5G HAT for Raspberry Pi₹17,600
Waveshare NB-IoT/Cat-M/GNSS HAT for Raspberry Pi: another version this guide coversWaveshare NB-IoT/Cat-M/GNSS HAT for Raspberry Pi₹3,839
Waveshare SIM7028 NB-IoT HAT for Raspberry Pi: another version this guide coversWaveshare SIM7028 NB-IoT HAT for Raspberry Pi₹2,984
Waveshare GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi: another version this guide coversWaveshare GSM/GPRS/GNSS/Bluetooth HAT for Raspberry Pi₹2,466
Waveshare R800C GSM/GPRS HAT for Raspberry Pi: another version this guide coversWaveshare R800C GSM/GPRS HAT for Raspberry Pi₹2,028
Raspberry Pi 4 Model B (4 GB): the most common HAT hostRaspberry Pi 4 Model B with 4GB RAM₹11,461Closest match, check the specs
Alternatives and when to choose them
- SIM7600 module: the module on its own.
- A7672S module: Cat-1 for microcontrollers.
- Industrial 4G routers: ready-made boxes.
Common mistakes to avoid
- Running without antennas.
- Weak power for 5G modems.
- Wrong APN.
- Unsupported bands.
Frequently asked questions
How do I get internet on a Pi with a 4G HAT?
Insert a data SIM, set the APN and connect with ModemManager or QMI.
Why does the modem not register?
The APN is wrong, an antenna is missing, or the modem does not support the operator's band.
Can the HAT send SMS?
Yes. Send SMS with AT commands or with ModemManager's mmcli tool.
Do I need two antennas?
For best speed, yes; one works with less throughput.
Is 5G worth it on a Pi?
Only where 5G coverage exists; USB 3 bandwidth also limits real speed on a Pi.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.



