Component guide · Intermediate · 3 min read
Quectel EC200U and EC800M 4G LTE Cat-1 Module

Setup and AT Commands
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The Quectel EC200U is a 4G LTE Cat-1 module with GNSS, made for IoT trackers, meters and payment terminals. It covers Indian LTE bands, falls back to 2G, and has built-in TCP, HTTP and MQTT stacks controlled by AT commands. The EC800M is a smaller Cat-1 module in an SMD package for compact PCBs. Both need a supply that handles 2 A bursts and an LTE antenna.
Key specs at a glance
- Network
- LTE Cat-1 (10/5 Mbps), GSM fallback on EC200U
- GNSS
- GPS, GLONASS, BeiDou, Galileo (EC200U GNSS versions)
- Supply
- 3.4 to 4.5 V module, 2 A peaks
- Interfaces
- UART, USB 2.0, PCM audio
- Package
- LCC (EC200U), small LCC (EC800M)
- Stacks
- TCP/UDP, HTTP(S), MQTT(S), FTP by AT commands
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Quectel EC200U 4G LTE CAT1 & GNSS Module for IoT₹2,819
Option 2Quectel EC200U 4G/GSM Module (LTE Cat 1, LCC)₹2,509
Option 3Quectel EC800M-CN LTE Cat 1 Module (SMD)₹1,144
What the Quectel EC200U is
Quectel modules are common in Indian commercial IoT because they are certified and stocked locally. The built-in MQTT client (AT+QMTOPEN, AT+QMTCONN, AT+QMTPUB) means a small microcontroller can publish to a broker without a full TCP/IP library.
The bare modules need your own PCB with a supply, SIM holder, antenna matching and level shifting; the board versions add these for prototyping.
Quectel EC200U pinout
The pins on the Quectel EC200U and what each one does.
| Pin | Function |
|---|---|
| VBAT | 3.4 to 4.5 V supply |
| GND | Ground |
| MAIN_TXD / MAIN_RXD | Main UART (1.8 V logic) |
| PWRKEY | Pull low 500 ms to turn on |
| RESET_N | Reset |
| USB_DP / DM | USB data |
| ANT_MAIN / ANT_GNSS | Antenna pads |
| USIM | SIM interface |
- VBAT
- 3.4 to 4.5 V supply
- GND
- Ground
- MAIN_TXD / MAIN_RXD
- Main UART (1.8 V logic)
- PWRKEY
- Pull low 500 ms to turn on
- RESET_N
- Reset
- USB_DP / DM
- USB data
- ANT_MAIN / ANT_GNSS
- Antenna pads
- USIM
- SIM interface
Wiring the Quectel EC200U
The module's UART is 1.8 V; boards may add a level shifter, bare modules do not. Keep the VBAT trace short and wide with 100 uF plus 33 pF and 10 pF capacitors close to the pins, as the hardware design guide shows.
| Quectel EC200U pin | Arduino Uno | ESP32 |
|---|---|---|
| VBAT | 4 V buck output (2 A) | 4 V buck output (2 A) |
| GND | GND | GND |
| MAIN_TXD | D2 through level shifter | GPIO 16 through level shifter |
| MAIN_RXD | D3 through level shifter | GPIO 17 through level shifter |
| PWRKEY | D4 via NPN transistor | GPIO 4 via NPN transistor |
- VBAT
- Arduino Uno:
- 4 V buck output (2 A)
- ESP32:
- 4 V buck output (2 A)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- MAIN_TXD
- Arduino Uno:
- D2 through level shifter
- ESP32:
- GPIO 16 through level shifter
- MAIN_RXD
- Arduino Uno:
- D3 through level shifter
- ESP32:
- GPIO 17 through level shifter
- PWRKEY
- Arduino Uno:
- D4 via NPN transistor
- ESP32:
- GPIO 4 via NPN transistor
Example code
Use your operator's APN. For GNSS, send AT+QGPS=1 then AT+QGPSLOC=2 for latitude and longitude.
HardwareSerial m(2);
void at(const char* c, int w = 1000) { m.println(c); delay(w); while (m.available()) Serial.write(m.read()); }
void setup() {
Serial.begin(115200);
m.begin(115200, SERIAL_8N1, 16, 17);
delay(5000);
at("AT");
at("AT+CPIN?");
at("AT+CEREG?");
at("AT+QICSGP=1,1,\"jionet\",\"\",\"\",1"); // APN
at("AT+QIACT=1", 3000);
at("AT+QMTOPEN=0,\"test.mosquitto.org\",1883", 5000);
at("AT+QMTCONN=0,\"geekobot-ec200u\"", 3000);
at("AT+QMTPUB=0,0,0,0,\"geekobot/test\",5", 500);
m.print("hello");
delay(2000);
while (m.available()) Serial.write(m.read());
}
void loop() {}Setup and tuning
follow Quectel's hardware design guide for power, SIM and antenna layout on custom PCBs.
use the Quectel EVB or a board version with USB and QCOM or minicom first.
a 50 ohm trace or IPEX to SMA pigtail to an LTE antenna.
use the certified module variant for products sold in India.
What you need
Shop this list8 of 9 found in our store · ₹7,291
Quectel EC200U 4G LTE CAT1 & GNSS Module for IoT: the part this guide coversQuectel EC200U 4G LTE CAT1 & GNSS Module for IoT₹2,819
Quectel EC200U 4G/GSM Module (LTE Cat 1, LCC): another version this guide coversQuectel EC200U 4G/GSM Module (LTE Cat 1, LCC)₹2,509
Quectel EC800M-CN LTE Cat 1 Module (SMD): another version this guide coversQuectel EC800M-CN LTE Cat 1 Module (SMD)₹1,144
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- XL4015 5A buck converter: a supply that holds up during 2 A transmit burstsFind this part
4-channel logic level converter (BSS138): to connect 5 V and 3.3 V signals safely4-Channel Logic Level Converter (BSS138)₹20
GSM antenna with 1 m cable and SMA plug: for better signal than the stub antennaGSM Antenna SMA 5cm 900-1800MHz 2dBi₹46Closest match, check the specs
GPS antenna 1575.42 MHz with SMA: an active GPS antenna for the GNSS inputGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
Alternatives and when to choose them
- A7672S 4G module: SIMCom Cat-1 alternative.
- SIM7600 4G module: Cat-4 for higher data rates.
- 4G LTE modules: families compared.
Common mistakes to avoid
- Connecting 3.3 V or 5 V logic straight to the 1.8 V UART.
- Thin supply traces that sag during transmit.
- Forgetting to activate the PDP context before MQTT.
- Using a GNSS-less variant for tracking.
Frequently asked questions
Does EC200U work in India?
Yes, the EC200U-CN and EU variants cover Indian LTE bands; check the variant before buying.
EC200U or EC800M?
EC800M for small PCBs; EC200U when you need 2G fallback, GNSS or more interfaces.
Does it have MQTT built in?
Yes, AT+QMT commands.
Can I use it from Raspberry Pi?
Yes, over USB as a modem with the option driver.
How do I get location?
AT+QGPS=1 and AT+QGPSLOC on GNSS versions.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


