Component guide · Intermediate · 3 min read
SIM7600EI and SIM7600G-H 4G LTE Module

Setup, GNSS and Internet
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The SIMCom SIM7600 is a 4G LTE module with built-in GNSS, used for internet on Raspberry Pi and Jetson, remote cameras and trackers. The SIM7600EI covers India bands (Cat-1 or Cat-4), and the SIM7600G-H is the global Cat-4 version (up to 150 Mbps down). As a USB modem it appears as a network card on Linux; over UART an Arduino or ESP32 drives it with AT commands.
Key specs at a glance
- Network
- LTE Cat-4 (150/50 Mbps) on SIM7600G-H and EI Cat-4; Cat-1 (10/5 Mbps) on SIM7600EI Cat-1; 3G and 2G fallback
- GNSS
- GPS, GLONASS, BeiDou, Galileo
- Supply
- 3.4 to 4.2 V module; 5 V USB or DC on boards; 2 A peaks
- Interfaces
- USB 2.0 (AT, modem, NMEA, RNDIS/ECM), UART
- Forms
- Module, Waveshare HAT and USB dongle, Jetson Nano board, industrial USB modem
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1SIMCom SIM7600EI LTE Cat-1 Cellular Module w/ GNSS₹3,629
Option 2Nexcomm SIM7600EI 4G LTE CAT1 Modem GPS/GNSS IoT Board₹5,860
Option 3SIM7600EI 4G LTE CAT1/4 USB Modem w/ GNSS₹4,829
Option 4Waveshare SIM7600G-H 4G LTE & GNSS Communication Module₹8,809
Option 5Waveshare SIM7600G-H 4G Dongle w/ GNSS & Global Band₹6,809
Option 6Waveshare SIM7600G-H 4G GNSS Module for Jetson Nano, LTE CAT4₹7,559
What the SIM7600 4G LTE module is
On a Raspberry Pi or Jetson, plug it in by USB and use RNDIS or the qmi/wwan driver to get a network interface; then the Pi is online anywhere with mobile coverage. GNSS gives position on a separate NMEA port or by AT+CGPSINFO.
Use a Cat-4 version for video and remote desktop; Cat-1 is enough for telemetry and MQTT.
SIM7600 4G LTE module pinout
The pins on the SIM7600 4G LTE module and what each one does.
| Pin | Function |
|---|---|
| USB | Power, AT, data and GNSS ports |
| TXD / RXD | UART AT commands |
| PWRKEY | Power-on pulse (some boards auto-start) |
| MAIN / AUX antenna | LTE main and diversity antennas |
| GNSS antenna | Active GNSS antenna |
| SIM | Nano or micro SIM holder |
- USB
- Power, AT, data and GNSS ports
- TXD / RXD
- UART AT commands
- PWRKEY
- Power-on pulse (some boards auto-start)
- MAIN / AUX antenna
- LTE main and diversity antennas
- GNSS antenna
- Active GNSS antenna
- SIM
- Nano or micro SIM holder
Wiring the SIM7600 4G LTE module
Fit the main LTE antenna (and AUX on Cat-4 for full speed) before power-up. A Pi powering the HAT needs its full-rated supply; on weak supplies, power the module separately.
| SIM7600 4G LTE module pin | ESP32 over UART | Raspberry Pi |
|---|---|---|
| USB | - | Pi USB port (data + power) |
| TXD / RXD | ESP32 GPIO 16 / 17 | Pi GPIO 15 / 14 (HAT) |
| PWRKEY | ESP32 GPIO 4 | Pi GPIO 4 (HAT, D6 jumper) |
| Supply | 5 V 2 A | Pi 5 V (use the official supply) |
- USB
- ESP32 over UART:
- -
- Raspberry Pi:
- Pi USB port (data + power)
- TXD / RXD
- ESP32 over UART:
- ESP32 GPIO 16 / 17
- Raspberry Pi:
- Pi GPIO 15 / 14 (HAT)
- PWRKEY
- ESP32 over UART:
- ESP32 GPIO 4
- Raspberry Pi:
- Pi GPIO 4 (HAT, D6 jumper)
- Supply
- ESP32 over UART:
- 5 V 2 A
- Raspberry Pi:
- Pi 5 V (use the official supply)
Example code
The USB mode command differs by firmware; Waveshare's SIM7600 wiki lists the exact one for each board. On an ESP32, use TinyGSM with the SIM7600 modem type for MQTT and HTTPS.
# AT port is usually /dev/ttyUSB2
sudo apt install minicom
minicom -D /dev/ttyUSB2
# AT+CPIN? -> READY
# AT+CSQ -> signal
# AT+CGDCONT=1,"IP","jionet"
# AT$MYCONFIG="usbnetmode",0 (or AT+CUSBPIDSWITCH=9011,1,1 for RNDIS)
# AT+CGPS=1 -> GNSS on
# AT+CGPSINFO -> lat,N,lon,E,date,time,alt,speed
# After switching to RNDIS, a usb0 / eth1 interface appears:
ip addr
ping -I usb0 8.8.8.8Setup and tuning
SIM7600EI for India; SIM7600G-H works worldwide including India.
Raspberry Pi OS includes the option and qmi_wwan drivers; Windows needs SIMCom drivers.
set it with AT+CGDCONT before bringing up data.
Cat-4 at full speed gets warm; leave airflow around the dongle.
What you need
Shop this list10 of 11 found in our store · ₹49,670
SIMCom SIM7600EI LTE Cat-1 Cellular Module w/ GNSS: the part this guide coversSIMCom SIM7600EI LTE Cat-1 Cellular Module w/ GNSS₹3,629
Nexcomm SIM7600EI 4G LTE CAT1 Modem GPS/GNSS IoT Board: another version this guide coversNexcomm SIM7600EI 4G LTE CAT1 Modem GPS/GNSS IoT Board₹5,860
SIM7600EI 4G LTE CAT1/4 USB Modem w/ GNSS: another version this guide coversSIM7600EI 4G LTE CAT1/4 USB Modem w/ GNSS₹4,829
Waveshare SIM7600G-H 4G LTE & GNSS Communication Module: another version this guide coversWaveshare SIM7600G-H 4G LTE & GNSS Communication Module₹8,809
Waveshare SIM7600G-H 4G Dongle w/ GNSS & Global Band: another version this guide coversWaveshare SIM7600G-H 4G Dongle w/ GNSS & Global Band₹6,809
Waveshare SIM7600G-H 4G GNSS Module for Jetson Nano, LTE CAT4: another version this guide coversWaveshare SIM7600G-H 4G GNSS Module for Jetson Nano, LTE CAT4₹7,559
Raspberry Pi 4 Model B 4GB: to use the modem for internet over USBRaspberry Pi 4 Model B with 4GB RAM₹11,461Closest match, check the specs
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
GSM antenna with 1 m cable and SMA plug: for better signal than the stub antennaGSM Antenna SMA 5cm 900-1800MHz 2dBi₹46Closest match, check the specs
GPS antenna 1575.42 MHz with SMA: an active GPS antenna for the GNSS inputGPS Antenna 1575.42MHz SMA Male 3M Cable₹279Closest match, check the specs- XL4015 5A buck converter: a supply that holds up during 2 A transmit burstsFind this part
Alternatives and when to choose them
- A7672S 4G module: cheaper Cat-1 for India.
- 4G LTE modules: the chip families compared.
- Industrial 4G routers: ready-made routers and gateways.
Common mistakes to avoid
- Leaving the AUX antenna off a Cat-4 module and losing speed.
- Using the wrong ttyUSB port for AT commands.
- Running the HAT from a weak Pi supply.
- Expecting GNSS indoors.
Frequently asked questions
SIM7600EI or SIM7600G-H?
Both work in India. The G-H is global Cat-4; the EI is the India and Asia version.
Can a Raspberry Pi use it for internet?
Yes, as an RNDIS or QMI network interface over USB.
Does it support voice?
Yes, on networks and boards with audio.
How do I get GPS?
AT+CGPS=1 then AT+CGPSINFO, or read NMEA on the GNSS USB port.
Does it work with an ESP32?
Yes, over UART with TinyGSM.
Parts for this guide
Projects that use it
Put this into practice: 1 step-by-step build in our project library uses parts from this guide.
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


