Component guide · Intermediate · 3 min read
Seeed 24 GHz mmWave for XIAO and Human Static Presence Lite

Waveshare S3KM1110 and LilyGO T-Radar
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These are 24 GHz FMCW presence radars on boards made for quick projects. The Seeed XIAO module plugs onto a XIAO ESP32 for Home Assistant, the Human Static Presence Lite reports presence and movement over UART, the Waveshare board uses the S3KM1110 chip for micro-motion, and the LilyGO T-Radar combines a radar with an ESP32. All detect people sitting still.
Key specs at a glance
- Frequency
- 24 GHz FMCW
- Range
- About 5 to 8 m for motion, less for still presence
- Interface
- UART and GPIO outputs
- Supply
- About 3.3 to 5 V
- Platform
- XIAO, ESP32 and ESPHome friendly
- Readings
- Presence, motion, distance (model dependent)
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Seeed Studio 24GHz mmWave Sensor for XIAO – Human Static Presence Detection Module₹609
Option 2Seeed Studio 24GHz mmWave Sensor – Human Static Presence Module Lite – FMCW Radar, Configurable Parameters, Arduino & Home Assistant Support₹681
Option 3Waveshare Human Micro-Motion Detection mmWave Sensor, 24GHz Radar Based on S3KM1110, FMCW Technology₹329
Option 4LilyGO T-Radar PINMAP Board – ESP32 mmWave Radar Sensor Module₹2,299
What the Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards is
Seeed 24 GHz mmWave presence sensors, such as the MR24HPC1 and XIAO 24GHz mmWave kit, detect human presence, movement and even still people for smart home automation.
The radar chips differ, so check each wiki for the exact protocol and library. Seeed provides Arduino libraries and ESPHome configs; the XIAO board is the quickest way into Home Assistant.
All of these keep reporting presence while someone is still, unlike PIR.
Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards pinout
The pins on the Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards and what each one does.
| Pin | Function |
|---|---|
| 5V / 3V3 | Supply |
| GND | Ground |
| TX / RX | UART |
| S1 / S2 / OUT | Presence and motion outputs |
- 5V / 3V3
- Supply
- GND
- Ground
- TX / RX
- UART
- S1 / S2 / OUT
- Presence and motion outputs
Wiring the Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards
Connect the Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards like this.
| Seeed, Waveshare and LilyGO 24 GHz mmWave presence boards pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) or 3.3 V (check module) |
| GND | GND | GND |
| Radar TX | D10 (SoftwareSerial RX, low baud only) | GPIO 16 (RX2) |
| Radar RX | D11 | GPIO 17 (TX2) |
| OUT (if fitted) | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN) or 3.3 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Radar TX
- Arduino Uno:
- D10 (SoftwareSerial RX, low baud only)
- ESP32:
- GPIO 16 (RX2)
- Radar RX
- Arduino Uno:
- D11
- ESP32:
- GPIO 17 (TX2)
- OUT (if fitted)
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
For distance and states, use the maker's library or ESPHome configuration for that exact board.
// Motion radar with a digital OUT pin: HIGH while motion is seen (plus the hold time)
const int RADAR = 2; // ESP32: use GPIO 27
const int LED = 13;
void setup() {
pinMode(RADAR, INPUT);
pinMode(LED, OUTPUT);
Serial.begin(115200);
}
void loop() {
bool motion = digitalRead(RADAR);
digitalWrite(LED, motion);
static bool last = false;
if (motion != last) { Serial.println(motion ? "Motion" : "Clear"); last = motion; }
delay(20);
}Setup and tuning
5 V, GND, TX and RX to a microcontroller UART, or use the XIAO kit with ESPHome.
flash the ESPHome config from Seeed to report presence and distance.
set sensitivity, range and scene mode in the app or config.
wall at 1.5 m or ceiling, facing the area, away from fans.
set an unoccupied delay so lights do not switch off while you sit still.
What you need
Shop this list6 of 7 found in our store · ₹4,392
Seeed Studio Studio 24GHz mmWave Sensor for XIAO – Human Static Presence Detection Module: the part this guide coversSeeed Studio 24GHz mmWave Sensor for XIAO – Human Static Presence Detection Module₹609
Seeed Studio Studio 24GHz mmWave Sensor – Human Static Presence Module Lite – FMCW Radar, Configurable Parameters, Arduino & Home Assistant Support: another version this guide coversSeeed Studio 24GHz mmWave Sensor – Human Static Presence Module Lite – FMCW Radar, Configurable Parameters, Arduino & Home Assistant Support₹681
Waveshare Human Micro-Motion Detection mmWave Sensor, 24GHz Radar Based on S3KM1110, FMCW Technology: another version this guide coversWaveshare Human Micro-Motion Detection mmWave Sensor, 24GHz Radar Based on S3KM1110, FMCW Technology₹329
LilyGO T-Radar PINMAP Board – ESP32 mmWave Radar Sensor Module: another version this guide coversLilyGO T-Radar PINMAP Board – ESP32 mmWave Radar Sensor Module₹2,299
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs- Hi-Link HLK-LD2410 24 GHz presence radar: the most common hobby presence radarFind this part
Alternatives and when to choose them
- LD2410: the most common presence radar.
- DFRobot C4001: I2C Gravity board.
- LD2412 and LD2420: other Hi-Link modules.
Common mistakes to avoid
- Pointing at fans.
- Max sensitivity everywhere.
- Short unoccupied delay.
- Mounting through-wall facing.
Frequently asked questions
Can Seeed mmWave sensors detect a sleeping person?
Yes. They detect breathing-level movement, so sleeping people stay detected.
How do I add it to Home Assistant?
Use Seeed's ESPHome config on the XIAO ESP32 kit.
Why does it report presence in an empty room?
Fans, curtains or pets are moving in range; lower the sensitivity.
Can it see through walls?
Partly through thin walls, so aim the sensor away from neighbouring rooms.
Is the UART 3.3 V?
Yes, most Seeed mmWave modules use 3.3 V UART.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

