Component guide · Intermediate · 3 min read
DFRobot C4001 (25 m and 12 m), Fermion C4002

and SEN0395 24 GHz mmWave Human Presence Sensors
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The DFRobot C4001 is a 24 GHz FMCW radar that detects people moving or still, and reports distance and speed. The Gravity 12 m version has I2C and UART on one connector; the 25 m version uses UART. The Fermion C4002 is a smaller board and the SEN0395 is the earlier 9 m model. All work with DFRobot's Arduino library and run at 3.3 V.
Key specs at a glance
- Frequency
- 24 GHz FMCW
- Range
- About 12 m or 25 m for motion; less for still presence
- Beam
- About 100 x 40 degrees (C4001)
- Interface
- I2C (0x2A or 0x2B) and UART on Gravity
- Supply
- 3.3 V (Gravity accepts 3.3 to 5 V)
- Readings
- Presence, target distance, speed, energy
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1DFRobot C4001 mmWave Human Presence Detection Sensor (25 m Range, 100°x40° Beam, 3.3V, FMCW)₹1,569
Option 2DFRobot Gravity C4001 mmWave Human Presence Detection Sensor (12 m Range) – I2C & UART₹1,469
Option 3DFRobot Fermion C4002 mmWave Human Presence Sensor – 24GHz FMCW Radar, Static & Motion Detection (10m)₹1,249
Option 4DFRobot SEN0395 mmWave Radar Sensor (24GHz) for Human Presence Detection (9 m Range)₹3,600
What the DFRobot C4001, C4002 and SEN0395 mmWave presence sensors is
The DFRobot C4001 is a 24 GHz radar that detects people both moving and sitting still, and reports their distance and speed.
In presence mode the C4001 sets an output while anyone is in the zone, still or moving. In speed mode it reports the distance and speed of the strongest moving target.
You can set the detection range and trigger and hold delays, so it fits a desk, a room or a corridor.
DFRobot C4001, C4002 and SEN0395 mmWave presence sensors pinout
The pins on the DFRobot C4001, C4002 and SEN0395 mmWave presence sensors and what each one does.
| Pin | Function |
|---|---|
| VCC | 3.3 or 5 V (Gravity) |
| GND | Ground |
| SDA / TX | I2C data or UART TX |
| SCL / RX | I2C clock or UART RX |
| OUT | Presence output |
- VCC
- 3.3 or 5 V (Gravity)
- GND
- Ground
- SDA / TX
- I2C data or UART TX
- SCL / RX
- I2C clock or UART RX
- OUT
- Presence output
Wiring the DFRobot C4001, C4002 and SEN0395 mmWave presence sensors
Set the Gravity board's switch to I2C for this wiring.
| DFRobot C4001, C4002 and SEN0395 mmWave presence sensors pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 3V3 |
| GND | GND | GND |
| SDA | A4 | GPIO 21 |
| SCL | A5 | GPIO 22 |
| OUT | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 3V3
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- SDA
- Arduino Uno:
- A4
- ESP32:
- GPIO 21
- SCL
- Arduino Uno:
- A5
- ESP32:
- GPIO 22
- OUT
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
Function names follow DFRobot's library examples; use eSpeedMode and getTargetRange() for distance and speed.
#include <DFRobot_C4001.h>
DFRobot_C4001_I2C radar(&Wire, DEVICE_ADDR_0); // 0x2A
void setup() {
Serial.begin(115200);
while (!radar.begin()) { Serial.println("C4001 not found"); delay(1000); }
radar.setSensorMode(eExitMode); // presence mode
radar.setDetectionRange(30, 1000, 1000); // min, max, trigger range in cm
}
void loop() {
Serial.println(radar.motionDetection() ? "Someone present" : "Empty");
delay(200);
}Setup and tuning
set the Gravity switch for I2C or UART and match it in the library.
mount about 1.5 to 2.5 m high, angled at the area to watch.
set minimum and maximum range in code to ignore areas you do not care about.
lower sensitivity if fans, curtains or plants cause false detections.
allow a few seconds after power-up before trusting the output.
What you need
Shop this list6 of 8 found in our store · ₹8,415
DFRobot C4001 mmWave Human Presence Detection Sensor (25 m Range, 100°x40° Beam, 3.3V, FMCW): the part this guide coversDFRobot C4001 mmWave Human Presence Detection Sensor (25 m Range, 100°x40° Beam, 3.3V, FMCW)₹1,569
DFRobot Gravity C4001 mmWave Human Presence Detection Sensor (12 m Range) – I2C & UART: another version this guide coversDFRobot Gravity C4001 mmWave Human Presence Detection Sensor (12 m Range) – I2C & UART₹1,469
DFRobot Fermion C4002 mmWave Human Presence Sensor – 24GHz FMCW Radar, Static & Motion Detection (10m): another version this guide coversDFRobot Fermion C4002 mmWave Human Presence Sensor – 24GHz FMCW Radar, Static & Motion Detection (10m)₹1,249
DFRobot SEN0395 mmWave Radar Sensor (24GHz) for Human Presence Detection (9 m Range): another version this guide coversDFRobot SEN0395 mmWave Radar Sensor (24GHz) for Human Presence Detection (9 m Range)₹3,600
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389- Uno R3 development board: the controller used in the wiring tableFind this part
- Hi-Link HLK-LD2410 24 GHz presence radar: the most common hobby presence radarFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- LD2410: cheaper Hi-Link presence radar.
- Seeed 24 GHz sensors: XIAO and Home Assistant ready.
- Trajectory radars: positions of several people.
Common mistakes to avoid
- Pointing it at a fan or moving curtain.
- Leaving the range at maximum in a small room.
- Mismatching the I2C or UART switch and code.
- Mounting it behind metal.
Frequently asked questions
Can the C4001 detect a sleeping person?
Yes. It senses the small movement of breathing, so a still person stays detected.
What is the difference between the 12 m and 25 m versions?
The 25 m version reaches further for motion and uses UART; the 12 m version has I2C and UART.
Why does it detect someone when the room is empty?
Moving objects like fans or curtains, or reflections, can trigger it. Lower sensitivity or limit the range.
Can it see through walls?
It can partly pass thin walls and furniture, which can cause false detections next door.
Does it work with ESP32 and Home Assistant?
Yes. Use the library with an ESP32, or ESPHome for Home Assistant.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


