Component guide · Advanced · 3 min read
Hi-Link HLK-LD2450, LD2452, LD2460

24 GHz) and LD6001A, B, C, LD6002B, LD6003D (60 GHz) Trajectory Tracking Radars
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Trajectory radars report where each person is, not just whether someone is there. The LD2450 tracks up to three people with X and Y position and speed out to about 6 m, sending frames over UART at 256000 baud. The 60 GHz LD6001 and LD6003D cover rooms from the ceiling, and the LD6001C counts heads. Use them for zones, people counting and smart lighting.
Key specs at a glance
- Frequency
- 24 GHz (LD2450, LD2452, LD2460) or 60 GHz (LD600x)
- Targets
- Up to 3 (LD2450) or more on 60 GHz models
- Range
- About 6 m (LD2450)
- Output
- UART frames with X, Y, speed (256000 baud on LD2450)
- Supply
- 5 V (LD2450); check others
- Field
- About plus or minus 60 degrees
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hi-Link HLK-LD2450 24GHz Trajectory Detection Radar Sensor Module₹795
Option 2Hi-Link HLK-LD2460 24GHz Trajectory Detection Radar Sensor₹2,209
Option 3Hi-Link HLK-LD2452 24GHz Millimeter-Wave Motion Sensor Module – 5V, 60° Azimuth, ±30° Pitch, 6m Range₹839
Option 4Hi-Link HLK-LD6001A 60GHz Trajectory Detection Radar Sensor₹5,049
Option 5Hi-Link HLK-LD6001B 60GHz Trajectory Detection Radar Sensor₹5,049
Option 6Hi-Link HLK-LD6001C 60GHz Head Counting Radar Sensor – TTL Serial₹3,629
What the Hi-Link LD2450 and LD6001 trajectory radars is
The Hi-Link HLK-LD2450 is a 24 GHz radar that tracks up to three people at once and reports their X and Y position and speed, for zones and movement tracking.
Each LD2450 frame starts AA FF 03 00, carries three 8-byte targets and ends 55 CC. Each target has X and Y in mm and speed in cm/s, with the top bit used as a sign.
With positions you can define zones in software: a chair, a door, a bed. ESPHome has an LD2450 component that does this for Home Assistant.
Hi-Link LD2450 and LD6001 trajectory radars pinout
The pins on the Hi-Link LD2450 and LD6001 trajectory radars and what each one does.
| Pin | Function |
|---|---|
| 5V | Supply |
| GND | Ground |
| TX | Target frames |
| RX | Commands |
- 5V
- Supply
- GND
- Ground
- TX
- Target frames
- RX
- Commands
Wiring the Hi-Link LD2450 and LD6001 trajectory radars
Connect the Hi-Link LD2450 and LD6001 trajectory radars like this.
| Hi-Link LD2450 and LD6001 trajectory radars pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) or 3.3 V (check module) |
| GND | GND | GND |
| Radar TX | D10 (SoftwareSerial RX, low baud only) | GPIO 16 (RX2) |
| Radar RX | D11 | GPIO 17 (TX2) |
| OUT (if fitted) | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN) or 3.3 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Radar TX
- Arduino Uno:
- D10 (SoftwareSerial RX, low baud only)
- ESP32:
- GPIO 16 (RX2)
- Radar RX
- Arduino Uno:
- D11
- ESP32:
- GPIO 17 (TX2)
- OUT (if fitted)
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
The 60 GHz models use other frame formats; see their protocol documents.
// LD2450 frame: AA FF 03 00 | 3 x (X, Y, speed, resolution) 16-bit LE | 55 CC
int16_t val(uint8_t lo, uint8_t hi) {
uint16_t r = lo | (hi << 8);
int16_t v = r & 0x7FFF;
return (r & 0x8000) ? v : -v; // top bit set = positive
}
const uint8_t HEAD[4] = {0xAA, 0xFF, 0x03, 0x00};
void setup() {
Serial.begin(115200);
Serial2.begin(256000, SERIAL_8N1, 16, 17);
}
void loop() {
static uint8_t f[30]; static int n = 0;
while (Serial2.available()) {
uint8_t b = Serial2.read();
if (n < 4 && b != HEAD[n]) { n = 0; continue; }
f[n++] = b;
if (n == 30) {
for (int t = 0; t < 3; t++) {
uint8_t *p = f + 4 + t * 8;
if (p[0] | p[1] | p[2] | p[3]) Serial.printf("T%d x=%d mm y=%d mm v=%d cm/s ", t + 1, val(p[0], p[1]), val(p[2], p[3]), val(p[4], p[5]));
}
Serial.println(); n = 0;
}
}
}Setup and tuning
5 V, GND, TX and RX to the microcontroller UART at 256000 baud.
use the LD2450 component to get target positions and zone counts in Home Assistant.
set up to three rectangle zones to include or exclude areas.
wall-mount at 1.5 to 2 m, facing the room; range is up to about 6 m.
use the HLKRadarTool app to view targets and change settings.
What you need
Shop this list11 of 12 found in our store · ₹21,611
Hi-Link HLK-LD2450 24GHz Trajectory Detection Radar Sensor Module: the part this guide coversHi-Link HLK-LD2450 24GHz Trajectory Detection Radar Sensor Module₹795
Hi-Link HLK-LD2460 24GHz Trajectory Detection Radar Sensor: another version this guide coversHi-Link HLK-LD2460 24GHz Trajectory Detection Radar Sensor₹2,209
Hi-Link HLK-LD2452 24GHz Millimeter-Wave Motion Sensor Module – 5V, 60° Azimuth, ±30° Pitch, 6m Range: another version this guide coversHi-Link HLK-LD2452 24GHz Millimeter-Wave Motion Sensor Module – 5V, 60° Azimuth, ±30° Pitch, 6m Range₹839
Hi-Link HLK-LD6001A 60GHz Trajectory Detection Radar Sensor: another version this guide coversHi-Link HLK-LD6001A 60GHz Trajectory Detection Radar Sensor₹5,049
Hi-Link HLK-LD6001B 60GHz Trajectory Detection Radar Sensor: another version this guide coversHi-Link HLK-LD6001B 60GHz Trajectory Detection Radar Sensor₹5,049
Hi-Link HLK-LD6001C 60GHz Head Counting Radar Sensor – TTL Serial: another version this guide coversHi-Link HLK-LD6001C 60GHz Head Counting Radar Sensor – TTL Serial₹3,629
Hi-Link HLK-LD6002B 60GHz Trajectory Detection Radar Sensor – FMCW, UART/GPIO Output: another version this guide coversHi-Link HLK-LD6002B 60GHz Trajectory Detection Radar Sensor – FMCW, UART/GPIO Output₹1,679
Hi-Link HLK-LD6003D 60GHz Trajectory Detection Radar Sensor – FMCW, 6m Range, ±60° FOV: another version this guide coversHi-Link HLK-LD6003D 60GHz Trajectory Detection Radar Sensor – FMCW, 6m Range, ±60° FOV₹1,749
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs- Hi-Link HLK-LD2410 24 GHz presence radar: the most common hobby presence radarFind this part
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Alternatives and when to choose them
- LD2412 and LD2420: presence only, simpler.
- Vital sign radars: breathing and falls.
- 3D depth cameras: images instead of points.
Common mistakes to avoid
- Using the wrong baud rate.
- Mounting it too low or tilted.
- Expecting presence of motionless people.
- Facing it toward fans or curtains.
Frequently asked questions
How many people can the LD2450 track?
Up to three targets at once, each with position and speed.
Can it detect someone standing still?
It is best with moving people; a still person may drop out after a while.
How do I use zones?
Set rectangles in the app or ESPHome so detections only count inside them.
Why are target positions jumpy?
Reflections from walls or furniture; average readings over time.
What baud rate does the LD2450 use?
256000 baud by default.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

