Component guide · Advanced · 3 min read
Vital Sign and Fall Detection mmWave Radars

Hi-Link LD6002, LD6002C, LD1125H, Seeed 24 GHz Fall and DFRobot C1001
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These radars sense the tiny chest movement of breathing and the heartbeat, or detect a fall, without any camera or wearable. The Hi-Link LD6002 and DFRobot C1001 work at 60 GHz; the LD1125H and Seeed fall module at 24 GHz. They report over UART, need the person in range and fairly still, and are for monitoring and research, not medical diagnosis.
Key specs at a glance
- Frequency
- 60 GHz (LD6002, LD6002C, C1001) or 24 GHz (LD1125H, Seeed fall)
- Readings
- Breathing rate, heart rate, presence, fall, sleep state (model dependent)
- Range
- About 0.4 to 1.5 m for vital signs; about 2 to 3 m for falls
- Interface
- UART (C1001 Gravity also I2C-style library)
- Supply
- 3.3 or 5 V
- Mounting
- Facing the chest, or ceiling for falls
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Hi-Link HLK-LD6002 60GHz FMCW Radar Heart Rate & Breathing Sensor Module₹1,989
Option 2Hi-Link HLK-LD6002C 60GHz Heart Rate Detecting Sensor Module – UART Interface₹2,379
Option 3Hi-Link LD1125H 24GHz Breathing Detection Radar Sensor Module – FMCW Modulation, Serial Output₹1,449
Option 4Seeed Studio 24GHz mmWave Fall Detection Radar Sensor Module₹3,416
Option 5DFRobot C1001 60 GHz mmWave Indoor Fall Detection Sensor for Arduino ESP32 micro:bit – 11m Range₹3,516
What the Breathing, heart rate and fall detection radars is
Vital signs and fall detection radars, such as the Seeed MR60BHA2 and MR60FDA2, use 60 GHz mmWave to detect breathing, heart rate trends and falls without cameras.
Vital sign readings need the person still and within about a metre or so, facing the sensor. Movement swamps the tiny signal.
Fall detection works from the ceiling or high wall, watching for a sudden drop in height followed by no movement. Test in the real room before relying on it, and never use it as a medical device.
Breathing, heart rate and fall detection radars pinout
The pins on the Breathing, heart rate and fall detection radars and what each one does.
| Pin | Function |
|---|---|
| VCC | Supply |
| GND | Ground |
| TX / RX | UART frames |
| GPIO | Event outputs on some models |
- VCC
- Supply
- GND
- Ground
- TX / RX
- UART frames
- GPIO
- Event outputs on some models
Wiring the Breathing, heart rate and fall detection radars
Connect the Breathing, heart rate and fall detection radars like this.
| Breathing, heart rate and fall detection radars pin | Arduino Uno | ESP32 |
|---|---|---|
| VCC | 5 V | 5 V (VIN) or 3.3 V (check module) |
| GND | GND | GND |
| Radar TX | D10 (SoftwareSerial RX, low baud only) | GPIO 16 (RX2) |
| Radar RX | D11 | GPIO 17 (TX2) |
| OUT (if fitted) | D2 | GPIO 27 |
- VCC
- Arduino Uno:
- 5 V
- ESP32:
- 5 V (VIN) or 3.3 V (check module)
- GND
- Arduino Uno:
- GND
- ESP32:
- GND
- Radar TX
- Arduino Uno:
- D10 (SoftwareSerial RX, low baud only)
- ESP32:
- GPIO 16 (RX2)
- Radar RX
- Arduino Uno:
- D11
- ESP32:
- GPIO 17 (TX2)
- OUT (if fitted)
- Arduino Uno:
- D2
- ESP32:
- GPIO 27
Example code
Each maker uses its own frame format; use DFRobot's C1001 library or the Seeed and Hi-Link protocol documents. Set BAUD to the module's rate (often 115200).
// Print a radar's UART frames in hex, to check the baud rate and match the protocol document
const long BAUD = 256000; // Hi-Link 24 GHz default; many others use 115200 or 9600
void setup() {
Serial.begin(921600);
Serial2.begin(BAUD, SERIAL_8N1, 16, 17); // ESP32 RX2 = 16, TX2 = 17
}
void loop() {
while (Serial2.available()) {
uint8_t b = Serial2.read();
if (b < 0x10) Serial.print('0');
Serial.print(b, HEX);
Serial.print(' ');
if (b == 0x55 || b == 0xF5 || b == 0x04) Serial.println(); // common frame-tail bytes
}
}Setup and tuning
5 V, GND and UART TX/RX; or use the ESPHome kit versions.
for vital signs, face the person within about 1 to 1.5 m; for falls, mount on the ceiling or wall as specified.
breathing readings need the person to stay fairly still.
use ESPHome to send data to Home Assistant.
they show trends and alerts, not medical diagnosis.
What you need
Shop this list9 of 9 found in our store · ₹13,389
Hi-Link HLK-LD6002 60GHz FMCW Radar Heart Rate & Breathing Sensor Module: the part this guide coversHi-Link HLK-LD6002 60GHz FMCW Radar Heart Rate & Breathing Sensor Module₹1,989
Hi-Link HLK-LD6002C 60GHz Heart Rate Detecting Sensor Module – UART Interface: another version this guide coversHi-Link HLK-LD6002C 60GHz Heart Rate Detecting Sensor Module – UART Interface₹2,379
Hi-Link LD1125H 24GHz Breathing Detection Radar Sensor Module – FMCW Modulation, Serial Output: another version this guide coversHi-Link LD1125H 24GHz Breathing Detection Radar Sensor Module – FMCW Modulation, Serial Output₹1,449
Seeed Studio 24GHz mmWave Fall Detection Radar Sensor Module: another version this guide coversSeeed Studio 24GHz mmWave Fall Detection Radar Sensor Module₹3,416
DFRobot C1001 60 GHz mmWave Indoor Fall Detection Sensor for Arduino ESP32 micro:bit – 11m Range: another version this guide coversDFRobot C1001 60 GHz mmWave Indoor Fall Detection Sensor for Arduino ESP32 micro:bit – 11m Range₹3,516
ESP32-WROOM-32 38-pin development board: for Wi-Fi logging and dashboardsESP32-WROOM-32 38-Pin Development Board₹389
USB to TTL serial converter: to talk to the module from a PCUSB to TTL Serial Converter (CH340G / CP2102 / FT232RL / PL2303)₹85Closest match, check the specs
0.96 inch OLED display 128x64: to show readings without a computer0.96" OLED Display 128x64₹139Closest match, check the specs
Buzzer module 3.3-5 V: for an audible alarmBuzzer Module 3.3–5V₹27
Alternatives and when to choose them
- Trajectory radars: where people are.
- Presence radar: is someone there.
- DFRobot C4001: presence and distance.
Common mistakes to avoid
- Treating readings as medical data.
- Mounting at the wrong height.
- Too far from the person.
- Fans in view.
Frequently asked questions
Can mmWave radar measure heart rate?
It estimates heart rate trends from chest movement, but not medically.
Where should a fall detection radar be mounted?
On the ceiling or wall at the height the manual specifies.
Does it use a camera?
No. It uses radar, which is more private than a camera.
Why are breathing readings missing?
The person is moving too much or is too far from the sensor.
Can it alert family if someone falls?
Yes, by sending fall alerts through Home Assistant or the vendor app.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
