Buying guide · Beginner · 3 min read
Standard, Water-Washable and ABS-Like Resins for MSLA Printers
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Resin printers harden liquid photopolymer with UV light and give much finer detail than filament printers. Standard resin is cheap and detailed but brittle and washes in isopropyl alcohol. Water-washable resin cleans in plain water, ABS-like and tough resins resist impact. Always wear nitrile gloves, ventilate, wash, then post-cure under UV.
Key specs at a glance
- Printer type
- MSLA, DLP or SLA printers with a UV light source around 405 nm
- Standard resin
- Good detail, brittle, wash in isopropyl alcohol
- Water-washable
- Rinse in water, slightly softer detail, waste water needs care
- ABS-like and tough
- Higher impact strength, often more viscous
- Layer height
- Typically 0.03 to 0.1 mm
- Exposure
- Set per resin and printer; use the maker's profile
Resin types
Choose the resin by what the part must do.
| Resin | Strengths | Weak points | Use for |
|---|---|---|---|
| Standard | Sharp detail, low cost, many colours | Brittle, needs IPA wash | Miniatures, prototypes, display models |
| Water-washable | Cleans in water, less IPA needed | Needs correct waste handling; some are slightly softer | Hobby printing on a budget |
| ABS-like / tough | Resists snapping and impacts | Thicker resin, needs warming in cold rooms | Functional parts, enclosures, snap fits |
| Castable | Burns out cleanly | Needs a special burnout process | Jewellery and metal casting |
| Flexible | Rubber-like parts | Hard to print and clean | Gaskets and soft parts |
- Standard
- Strengths:
- Sharp detail, low cost, many colours
- Weak points:
- Brittle, needs IPA wash
- Use for:
- Miniatures, prototypes, display models
- Water-washable
- Strengths:
- Cleans in water, less IPA needed
- Weak points:
- Needs correct waste handling; some are slightly softer
- Use for:
- Hobby printing on a budget
- ABS-like / tough
- Strengths:
- Resists snapping and impacts
- Weak points:
- Thicker resin, needs warming in cold rooms
- Use for:
- Functional parts, enclosures, snap fits
- Castable
- Strengths:
- Burns out cleanly
- Weak points:
- Needs a special burnout process
- Use for:
- Jewellery and metal casting
- Flexible
- Strengths:
- Rubber-like parts
- Weak points:
- Hard to print and clean
- Use for:
- Gaskets and soft parts
Print, wash, cure
- 1Level the plate and check the resin tank (FEP film) for dents and cloudiness.
- 2Print with the exposure times recommended for your resin and printer, in a room kept at 20 to 30 °C.
- 3Wash the part in 90 % or stronger isopropyl alcohol, or in water for water-washable resin. A wash and cure station does both jobs (see the stations in the shop).
- 4Dry for a few minutes, then post-cure under UV for 2 to 10 minutes depending on size.
- 5Remove supports after washing and before the final cure for easier cutting.
Safety and disposal
Uncured resin irritates skin and can cause allergies. Wear nitrile gloves, work in a ventilated space and keep resin away from children and pets. Never pour resin or dirty wash liquid into drains. Leave waste liquid in a clear container in sunlight (or under a UV lamp) until it hardens, filter out the solids, and throw them away with household waste. Follow your local rules for chemical waste.
Care and quality tips
- Replace the FEP film when it is cloudy or scratched; see the resin printing basics.
- Keep the resin bottle in the dark and shake before use.
- Filter the tank after failed prints to remove cured specks.
- Orient models at 30 to 45 degrees and add supports on overhangs.
- Do not leave a washed part sitting in IPA for hours; it can crack or become cloudy.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Skipping gloves and ventilation.
- Pouring wash liquid or resin down the drain.
- Using filament-printer settings for resin.
- Printing a cold resin and getting a failed first layer.
- Under-curing parts, leaving them sticky.
Frequently asked questions
Is water-washable resin better than standard resin?
It is easier to clean without IPA, but waste water still contains uncured resin and must be treated like chemical waste.
Which resin is strongest?
Tough and ABS-like resins. Standard resins are brittle.
How long should I cure a print?
A few minutes under UV for small parts; follow your resin's data sheet.
Can I use any resin in any printer?
Most 405 nm resins work, but exposure times differ; always set the printer's profile for that resin.
Why do my prints stick to the film?
Under-exposed layers, a dirty FEP or a poorly leveled plate. Check exposure first.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




