Buying guide · Advanced · 3 min read
Engineering Resins
Tough, ABS-Like, Nylon-Like and Castable Resin for Jewellery
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
Engineering resins trade the sharp detail of standard resin for strength. Tough and ABS-like resins survive snap-fits and impacts, nylon-like resins flex, and castable resins burn out without ash so you can cast metal jewellery. Print with the maker's exposure profile, do not over-cure tough resins, and follow the burnout schedule for castables.
Key specs at a glance
- Tough / ABS-like
- Higher elongation and impact strength than standard resin
- Nylon-like
- Flexible, wear resistant, for hinges and gears
- High temperature
- Resists deformation at higher heat, needs careful curing
- Castable
- Low ash, burns out cleanly in a plaster mould
- Exposure
- Longer than standard resin; set per resin and printer
- Safety
- Gloves, ventilation and proper waste curing
What each resin is for
Pick the property you need most.
| Resin | Property | Use for | Watch out for |
|---|---|---|---|
| Tough / ABS-like | Impact resistant | Snap-fits, enclosures, jigs | Over-curing makes it brittle |
| Nylon-like / flexible | Bendy and wear resistant | Hinges, clips, grips | Needs thicker walls |
| High temperature | Heat deflection | Moulds, hot-air parts | Strict cure schedule |
| Castable | Burns out with little ash | Jewellery and small metal parts | Needs a casting workflow |
| Standard | Fine detail | Miniatures, display | Brittle; see resin basics |
- Tough / ABS-like
- Property:
- Impact resistant
- Use for:
- Snap-fits, enclosures, jigs
- Watch out for:
- Over-curing makes it brittle
- Nylon-like / flexible
- Property:
- Bendy and wear resistant
- Use for:
- Hinges, clips, grips
- Watch out for:
- Needs thicker walls
- High temperature
- Property:
- Heat deflection
- Use for:
- Moulds, hot-air parts
- Watch out for:
- Strict cure schedule
- Castable
- Property:
- Burns out with little ash
- Use for:
- Jewellery and small metal parts
- Watch out for:
- Needs a casting workflow
- Standard
- Property:
- Fine detail
- Use for:
- Miniatures, display
- Watch out for:
- Brittle; see resin basics
Printing and curing
Use the exposure and lift speed on the resin label. Tough resins are thicker, so warm the room to 25 to 30 °C and stir well. Wash promptly and cure only as long as the data sheet says, because too much UV makes tough resins brittle and may warp thin parts. Support castable patterns lightly and keep walls thin so the burnout is clean.
Casting workflow (castable resin)
1. Print the pattern and wash thoroughly. Cure as the maker recommends. 2. Attach the pattern to a sprue and cover it with investment plaster in a flask. 3. After the plaster sets, heat it in a burnout oven following the resin maker's schedule, which usually rises in stages to a high temperature to remove all resin. 4. Pour molten metal into the hot mould, then quench and break the plaster away. Burnout and casting involve high temperatures and fumes. Learn the process and use proper protective equipment and ventilation; see the resin safety notes.
Choosing a resin
- For functional prototypes choose a tough resin from a trusted brand and check the stated elongation and impact values.
- For jewellery check the resin is castable and the burnout schedule matches your oven.
- Keep exposure test prints for every new bottle.
- Store bottles closed and out of light.
Try it: 3d print cost calculator
Change the values and the diagram and results update as you type.
Common mistakes to avoid
- Over-curing a tough resin until it snaps.
- Using standard resin where impact strength is needed.
- Skipping the maker's burnout schedule and leaving ash in the cast.
- Pouring waste resin down the drain.
- Printing a cold, thick resin without warming it.
Frequently asked questions
Is ABS-like resin as tough as ABS plastic?
It is tougher than standard resin but still not the same as injection-moulded ABS.
Can I cast metal directly from any resin?
Only from resins sold as castable. Others leave ash or crack the mould.
How do I stop tough resin breaking?
Cure for the recommended time only and design with fillets and thicker walls.
Do I need a special printer?
No, but you need a printer that handles thicker resin and a good wash and cure setup.
Is castable resin safe?
Handle it like any resin with gloves and ventilation, and take extra care in burnout.
Parts for this guide
Calculators
Terms in this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.




