Component guide · Beginner · 3 min read
TP5000 1A Charger Module for Li-ion (4.2V) and LiFePO4 (3.6V)

Setup
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
The TP5000 is a switching 1-cell charger that can charge either Li-ion (4.2 V) or LiFePO4 (3.6 V) cells, selected by a solder jumper. Because it switches instead of burning off heat like the TP4056, it stays cooler at 1 A. It takes 4.5 to 6 V input, so USB or a 5 V supply works.
Key specs at a glance
- Input
- 4.5 to 6 V
- Chemistry
- Li-ion 4.2 V or LiFePO4 3.6 V (jumper)
- Charge current
- Up to 1 A (set by resistor)
- Type
- Switching CC/CV
- Status
- Charging and full LEDs
- Protection
- No discharge protection
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the TP5000 charger module is
The TP5000 module is a single-cell battery charger that uses a switching (buck) circuit. A jumper selects Li-ion (4.2 V) or LiFePO4 (3.6 V) charging, and it stays cooler than a TP4056 at 1 A.
Check the jumper before connecting a cell. Charging an LFP cell at 4.2 V damages it.
There is no over-discharge protection; add a protection board or use protected cells.
TP5000 charger module pinout
The pins on the TP5000 charger module and what each one does.
| Pin | Function |
|---|---|
| IN+ / IN- | 5 V input |
| BAT+ / BAT- | Cell |
| Jumper | Chemistry select |
- IN+ / IN-
- 5 V input
- BAT+ / BAT-
- Cell
- Jumper
- Chemistry select
Wiring the TP5000 charger module
Connect the TP5000 charger module like this.
| TP5000 charger module pin | Li-ion | LiFePO4 |
|---|---|---|
| IN | USB 5 V | 5 V supply |
| BAT | 18650 Li-ion (4.2 V jumper) | LiFePO4 cell (3.6 V jumper) |
- IN
- Li-ion:
- USB 5 V
- LiFePO4:
- 5 V supply
- BAT
- Li-ion:
- 18650 Li-ion (4.2 V jumper)
- LiFePO4:
- LiFePO4 cell (3.6 V jumper)
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
set the jumper for your cell before connecting it; the wrong setting over- or under-charges the cell.
set it with the resistor to no more than 1C (the cell's capacity in amps), up to 1 A.
use 4.5 to 6 V, from USB or a 5 V supply.
add a protection board, because the TP5000 only charges and does not stop over-discharge.
measure the full-charge voltage on the first charge.
What you need
Shop this list4 of 4 found in our store · ₹16,41,080
TP5000 1A Charger Module for Li-ion (4.2V) and LiFePO4 (3.6V): the part this guide coversTP5000 1A Charger Module for Li-ion (4.2V) and LiFePO4 (3.6V)₹67
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- TP4056 charger: Li-ion only, linear.
- Type-C fast charge board.
- 1S protection board.
Common mistakes to avoid
- Leaving the jumper on the wrong chemistry.
- Feeding it 12 V.
- Using it without a protection board.
- Charging a small cell at 1 A.
Frequently asked questions
Can the TP5000 charge LiFePO4 cells?
Yes. Set the jumper to the 3.6 V setting and it charges one LiFePO4 cell.
Is the TP5000 cooler than the TP4056?
Yes. It is a switching charger, so it wastes much less power as heat at 1 A.
Can I power it from 12 V?
No. The input range is 4.5 to 6 V. Use a buck converter to make 5 V first.
What charge current does it give?
Up to 1 A, set by a resistor on the board.
Does it protect the cell during use?
No. It only charges. Add a protection board for over-discharge and short circuits.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

