Component guide · Beginner · 3 min read
Type-C 3A Fast Charging Board for 1S Li-ion and LiPo

Wiring and Use
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
This Type-C board charges a single Li-ion or LiPo cell at up to 3 A from a USB-C source, three times faster than a TP4056. It suits large cells or parallel 18650 packs of 6,000 mAh or more. Fast charging small cells shortens their life, so match the current to roughly half the cell's capacity per hour (0.5C).
Key specs at a glance
- Input
- USB-C 5 V
- Charge voltage
- 4.2 V
- Current
- Up to 3 A
- Type
- Switching CC/CV
- Indicators
- Charging and full LEDs
- Cell
- 1S Li-ion or LiPo
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the Type-C 1S fast charging board is
Type-C 1S fast charge boards, such as IP2312 and IP5306 modules, charge a single 3.7 V Li-ion or LiPo cell from USB-C, often at 2 to 3 A, and some add 5 V boost output.
A 2,500 mAh cell should charge at about 1.25 A; 3 A suits about 6,000 mAh and above (for example, 2 or 3 x 18650 in parallel).
Use a 5 V 3 A USB-C supply and a good cable, or the board will reduce current.
Type-C 1S fast charging board pinout
The pins on the Type-C 1S fast charging board and what each one does.
| Pin | Function |
|---|---|
| USB-C | Input |
| B+ / B- | Cell |
- USB-C
- Input
- B+ / B-
- Cell
Wiring the Type-C 1S fast charging board
Connect the Type-C 1S fast charging board like this.
| Type-C 1S fast charging board pin | 18650 pack | LiPo |
|---|---|---|
| B+ / B- | 1S2P 18650 pack | Large LiPo |
| USB-C | 5 V 3 A adapter | Same |
- B+ / B-
- 18650 pack:
- 1S2P 18650 pack
- LiPo:
- Large LiPo
- USB-C
- 18650 pack:
- 5 V 3 A adapter
- LiPo:
- Same
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
use only one Li-ion or LiPo cell, or several cells in parallel.
check the charge current and make sure the cell can take it (often 0.5 C to 1 C).
B+ and B- to the cell, with correct polarity.
use a protected cell or add a DW01 protection board for over-discharge.
fast charging warms the chip; give it airflow.
What you need
Shop this list4 of 4 found in our store · ₹16,41,095
Type-C 3A Fast Charging Board for 1S Li-ion / LiPo: the part this guide coversType-C 3A Fast Charging Board for 1S Li-ion / LiPo₹82
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
18650 battery holder: to hold the cellBattery Holder₹45
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
Alternatives and when to choose them
- TP4056 charger: 1 A.
- TP5000 charger: Li-ion or LFP.
- Multi-cell boost charger.
Common mistakes to avoid
- Charging small cells too fast.
- Reversing battery polarity.
- Using it for series packs.
- No discharge protection.
Frequently asked questions
Can I charge a small LiPo at 2 A?
No. A small cell needs a lower current; pick a board with matching current.
Does the board protect against over-discharge?
Many do not; check or add a protection board.
Can it charge two cells in series?
No. 1S boards are for single cells or parallel packs.
Why does the LED blink?
It shows charging status or a fault; check the module notes.
Does it support USB PD fast chargers?
Many work with any 5 V USB-C charger; PD is not needed.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.

