Component guide · Beginner · 3 min read
Type-C Multi-Cell Boost Charger Module (2S, 3S, 4S)

Charging Packs from USB
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
This module boosts USB-C 5 V up to the full-charge voltage of a 2S (8.4 V), 3S (12.6 V) or 4S (16.8 V) Li-ion pack and charges it with CC/CV. It lets you charge robot and speaker packs from any USB charger. It does not balance cells, so the pack still needs a BMS with balancing.
Key specs at a glance
- Input
- USB-C 5 V (some accept 9 V)
- Output
- 8.4 V (2S), 12.6 V (3S) or 16.8 V (4S)
- Current
- About 1 to 2 A charge
- Type
- Boost CC/CV
- Indicators
- LEDs
- Balancing
- None
A shorted, over-charged or damaged lithium cell can get very hot and catch fire. Use a protection board or BMS, never short the terminals, charge on a non-flammable surface and do not leave a charging pack alone. Throw away cells that are swollen or dented.
What the Type-C multi-cell boost charger is
Type-C multi-cell boost chargers, such as IP2326 and SW6106 boards, boost USB-C 5 V up to charge 2S or 3S Li-ion packs.
Pick the version that matches your pack. A 3S module on a 2S pack overcharges it dangerously.
Charging from 5 V means high input current; a 2 A charge at 12.6 V needs over 5 A from USB in theory, so actual current is limited by the source.
Type-C multi-cell boost charger pinout
The pins on the Type-C multi-cell boost charger and what each one does.
| Pin | Function |
|---|---|
| USB-C | Input |
| B+ / B- | Pack (through BMS P+/P-) |
- USB-C
- Input
- B+ / B-
- Pack (through BMS P+/P-)
Wiring the Type-C multi-cell boost charger
Connect the Type-C multi-cell boost charger like this.
| Type-C multi-cell boost charger pin | 2S version | 3S version |
|---|---|---|
| B+ / B- | 2S pack via BMS | 3S pack via BMS |
| USB-C | 5 V 3 A adapter | Same |
- B+ / B-
- 2S version:
- 2S pack via BMS
- 3S version:
- 3S pack via BMS
- USB-C
- 2S version:
- 5 V 3 A adapter
- 3S version:
- Same
Example code
A minimal sketch to check the part works.
1. Connect the battery first, then the input source.
2. Measure charge voltage at the battery terminals.
3. Watch cell temperature during the first full charge.Setup and tuning
set or choose the board for your 2S or 3S pack.
these boards do not balance cells; use a BMS with balancing.
a 5 V 2 to 3 A USB-C supply gives the best charge rate.
connect B+ and B- correctly.
boost charging creates heat; keep the board ventilated.
What you need
Shop this list4 of 4 found in our store · ₹11,96,459
Type-C Multi-Cell Boost Charger Module (2S / 3S / 4S): the part this guide coversType-C Multi-Cell Boost Charger Module (2S / 3S / 4S)₹62
18650 Li-ion rechargeable cell: the cell to charge or protect18650 Li-ion Rechargeable Cell₹119Closest match, check the specs
Digital multimeter: to check supply and signal voltagesDigital Multimeter₹177
iMAX B6 balance charger: to balance-charge packs on the benchiMAX B6 Balance Charger₹2,339
Alternatives and when to choose them
Common mistakes to avoid
- Wrong cell count setting.
- No BMS on the pack.
- Weak USB supply.
- Using it for LiFePO4.
Frequently asked questions
Can I charge a 2S pack from USB?
Yes, with a boost charger board set for 2S.
Does the board balance cells?
No. Use a BMS with balancing for multi-cell packs.
How fast does it charge?
Usually 10 to 15 W, limited by the 5 V USB input.
Why does it get hot?
Boosting 5 V up to pack voltage loses some energy as heat, which is normal.
Can I charge LiFePO4?
Only with a board made for LiFePO4, because its charge voltages differ from Li-ion.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.
