Component guide · Intermediate · 5 min read
Waveshare ESP32-S3 Touch LCD Boards

2.8, 3.16, 3.49, 3.5, 4, 4.3, 5 and 7 Inch, Smart 86 Box and RGB LCD Driver Board
By Geekobot Learning Team · Updated 29 Oct 2026
On this page
These boards are complete touch panels: an ESP32-S3 with 8 MB PSRAM drives a 2.8 to 7 inch capacitive touch LCD, so you can build home control panels, machine HMIs, smart displays and dashboards. Larger boards use an RGB parallel interface and often add RS485, CAN, a microSD slot, battery charging or I/O for industrial use. The 86 box board fits a standard wall switch box.
Key specs at a glance
- Chip
- ESP32-S3 with 8 MB PSRAM and 8 or 16 MB flash
- Screens
- 2.8 to 7 inch, 320x240 up to 1024x600
- Touch
- Capacitive (GT911, CST816, FT6336)
- Interface
- SPI, QSPI or 16-bit RGB
- Extras
- RS485, CAN, SD card, RTC, IMU, speaker (model dependent)
- Software
- Arduino, ESP-IDF, LVGL, SquareLine Studio, ESPHome
Models in this guide
These are alternatives. Pick the one that fits your project; you only need one.
Option 1Waveshare ESP32-S3 2.8-Inch Capacitive Touch Display Development Board₹2,889
Option 2Waveshare ESP32-S3 2.8-Inch Capacitive Touch Round Display Dev Board₹5,349
Option 3Waveshare ESP32-S3 2.8-Inch LCD Development Board Type B (No Touch)₹3,539
Option 4Waveshare ESP32-S3 3.16-Inch 320×820 Display Development Board₹2,409
Option 5Waveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board₹3,409
Option 6Waveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board Type B₹4,919
What the Waveshare ESP32-S3 2.8 to 7 inch touch LCD boards is
Waveshare ESP32-S3 touch LCD boards combine an ESP32-S3 with 2.8 to 7-inch capacitive touch screens for HMI panels, dashboards and smart home controls.
Design the interface in SquareLine Studio or EEZ Studio, export LVGL code and add your logic. Larger RGB screens need PSRAM frame buffers, so keep the PSRAM setting on.
ESPHome and Home Assistant users can use several of these as wall panels. The RGB LCD driver board lets you attach your own 40-pin RGB panel.
Waveshare ESP32-S3 2.8 to 7 inch touch LCD boards pinout
The pins on the Waveshare ESP32-S3 2.8 to 7 inch touch LCD boards and what each one does.
| Pin | Function |
|---|---|
| USB-C | Power, flashing and serial (native USB on S3/C6/RP2350) |
| Display interface | SPI, QSPI, RGB parallel or MIPI to the built-in screen |
| Touch (I2C) | Capacitive touch controller on touch versions |
| Extras | IMU, RTC, microSD, battery charger, mic or speaker depending on board |
| Expansion header | Free GPIO, I2C and UART pads |
| RS485 / CAN terminals | On industrial 4.3 to 7 inch versions |
- USB-C
- Power, flashing and serial (native USB on S3/C6/RP2350)
- Display interface
- SPI, QSPI, RGB parallel or MIPI to the built-in screen
- Touch (I2C)
- Capacitive touch controller on touch versions
- Extras
- IMU, RTC, microSD, battery charger, mic or speaker depending on board
- Expansion header
- Free GPIO, I2C and UART pads
- RS485 / CAN terminals
- On industrial 4.3 to 7 inch versions
Wiring the Waveshare ESP32-S3 2.8 to 7 inch touch LCD boards
These boards are ready to use: the screen, touch and extras are already wired. Check the maker's wiki for the exact pins used by the display before connecting anything else to the header.
| Waveshare ESP32-S3 2.8 to 7 inch touch LCD boards pin | Connection | Note |
|---|---|---|
| USB-C | To a PC to flash | Hold BOOT if not detected |
| Battery | JST LiPo connector where fitted | 3.7V single cell only |
| Sensors | I2C pads or header | 3.3V logic |
| RS485 / CAN | A/B or H/L terminals | Terminate long buses |
- USB-C
- Connection:
- To a PC to flash
- Note:
- Hold BOOT if not detected
- Battery
- Connection:
- JST LiPo connector where fitted
- Note:
- 3.7V single cell only
- Sensors
- Connection:
- I2C pads or header
- Note:
- 3.3V logic
- RS485 / CAN
- Connection:
- A/B or H/L terminals
- Note:
- Terminate long buses
Example code
Waveshare publishes ready examples (Arduino, ESP-IDF and LVGL) for each board; start from them and change the UI. Enable 'USB CDC On Boot' in the Arduino IDE for serial output on native-USB boards. RGB panels use Arduino_ESP32RGBPanel with the pin list from the wiki.
#include <Arduino_GFX_Library.h>
// Example pins for an ST7789 SPI screen: copy the real ones from the board wiki
Arduino_DataBus *bus = new Arduino_ESP32SPI(8 /*DC*/, 9 /*CS*/, 10 /*SCK*/, 11 /*MOSI*/);
Arduino_GFX *gfx = new Arduino_ST7789(bus, 12 /*RST*/, 0 /*rotation*/, true /*IPS*/, 172, 320);
void setup() {
pinMode(13, OUTPUT); digitalWrite(13, HIGH); // backlight pin
gfx->begin();
gfx->fillScreen(BLACK);
gfx->setTextColor(CYAN);
gfx->setTextSize(3);
gfx->setCursor(10, 40);
gfx->println("Hello!");
}
void loop() {}Setup and tuning
select ESP32S3 Dev Module with OPI PSRAM and the right flash size.
use LVGL or SquareLine Studio with the Waveshare demo as a base.
the touch chip (GT911, CST816 and others) uses I2C; check the wiki for pins.
use a 5 V 1 A supply for larger screens.
many boards add RS485, CAN or SD card slots.
What you need
Shop this list19 of 20 found in our store · ₹71,031
Waveshare ESP32-S3 2.8-Inch Capacitive Touch Display Development Board: the part this guide coversWaveshare ESP32-S3 2.8-Inch Capacitive Touch Display Development Board₹2,889
Waveshare ESP32-S3 2.8-Inch Capacitive Touch Round Display Dev Board: another version this guide coversWaveshare ESP32-S3 2.8-Inch Capacitive Touch Round Display Dev Board₹5,349
Waveshare ESP32-S3 2.8-Inch LCD Development Board Type B (No Touch): another version this guide coversWaveshare ESP32-S3 2.8-Inch LCD Development Board Type B (No Touch)₹3,539
Waveshare ESP32-S3 3.16-Inch 320×820 Display Development Board: another version this guide coversWaveshare ESP32-S3 3.16-Inch 320×820 Display Development Board₹2,409
Waveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board: another version this guide coversWaveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board₹3,409
Waveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board Type B: another version this guide coversWaveshare ESP32-S3 3.5-Inch Capacitive Touch Display Development Board₹3,409
Waveshare ESP32-S3 High-Performance Dev Board Case B w/ 3.49″ IPS Touch: another version this guide coversWaveshare ESP32-S3 High-Performance Dev Board Case B w/ 3.49″ IPS Touch₹3,779
Waveshare ESP32-S3R8 Dev Board Case A w/ 3.49″ IPS Touch: another version this guide coversWaveshare ESP32-S3R8 Dev Board Case A w/ 3.49″ IPS Touch₹3,489
Waveshare ESP32-S3 4-Inch 480×480 Capacitive Touch Display Dev Board: another version this guide coversWaveshare ESP32-S3 4-Inch 480×480 Capacitive Touch Display Dev Board₹4,299
Waveshare ESP32-S3 4-Inch LCD Display Development Board w/ Touch: another version this guide coversWaveshare ESP32-S3 4-Inch LCD Display Development Board w/ Touch₹4,089
Waveshare ESP32-S3 Smart 86 Box Dev Board w/ 4-Inch IPS Touch: another version this guide coversWaveshare ESP32-S3 Smart 86 Box Dev Board w/ 4-Inch IPS Touch₹5,139
Waveshare ESP32-S3 4.3-Inch LCD Development Board: another version this guide coversWaveshare ESP32-S3 4.3-Inch LCD Development Board₹3,779
Waveshare ESP32-S3 5-Inch Display Development Board: another version this guide coversWaveshare ESP32-S3 5-Inch Display Development Board₹4,719
Waveshare ESP32-S3 5inch Display Development Board w/ 800×480 LCD: another version this guide coversWaveshare ESP32-S3 5inch Display Development Board w/ 800×480 LCD₹4,409
Waveshare ESP32-S3 7inch Display Development Board w/ 800×480 LCD: another version this guide coversWaveshare ESP32-S3 7inch Display Development Board w/ 800×480 LCD₹3,969
Waveshare ESP32-S3 7-Inch 1024×600 Touch Display Development Board Type B: another version this guide coversWaveshare ESP32-S3 7-Inch 1024×600 Touch Display Development Board Type B₹4,929
Waveshare ESP32-S3 7-inch Capacitive Touch Display Board: another version this guide coversWaveshare ESP32-S3 7-inch Capacitive Touch Display Board₹4,799
Waveshare ESP32-S3 RGB LCD Driver Board w/ ESP32-S3-WROOM-1-N8R8: another version this guide coversWaveshare ESP32-S3 RGB LCD Driver Board w/ ESP32-S3-WROOM-1-N8R8₹1,569
USB-C cable: for power, flashing and the serial monitorArduino USB-C to USB-C Cable w/ USB-A Adapter₹1,059Closest match, check the specs- MAX98357 I2S amplifier: adds sound to boards without a speakerFind this part
Alternatives and when to choose them
- Small ESP32-S3 display boards: round and AMOLED.
- ESP32 HMI panels: WT32, CrowPanel, SenseCAP.
- ESP32 touchscreen boards: CYD style boards.
Common mistakes to avoid
- Wrong PSRAM setting.
- Weak power supply.
- Starting from scratch instead of the demo.
- Wrong touch driver.
Frequently asked questions
How do I build a GUI for the touch LCD?
Use SquareLine Studio to design LVGL screens and add them to the demo project.
Why does the screen flicker?
The PSRAM mode or display timing settings do not match the board.
Why does touch not work?
The touch I2C pins or the touch driver do not match the board.
Can I use ESPHome?
Some boards have community ESPHome configs you can start from.
How much power does it need?
About 5 V at 0.5 to 1 A depending on screen size.
Parts for this guide
Keep learning
Sources
Written by the Geekobot team from manufacturer datasheets. Always check the datasheet for the exact part and variant you buy.


