LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsPainters prefer even north light with no sudden swings. Place the BH1750 at the canvas and watch the lux on the LCD as clouds pass and the sun moves, so you can pick the best working hours and place the lamps.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Follow the colours: red is power, dark grey is ground, blue is a signal.
art_studio_light_checker.inoVerify & upload in Electrolark// Art studio light checker
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "art-studio-light-checker"
#include <Wire.h>
#include <BH1750.h>
#include <LiquidCrystal_I2C.h>
BH1750 lightMeter;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float lux = 0;
const unsigned long READ_EVERY_MS = 500;
unsigned long lastRead = 0;
const char* statusText = "OK";
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Light "));
lcd.print(lux, 0);
lcd.print(F(" lx"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void setup() {
Serial.begin(115200);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
lcd.init();
lcd.backlight();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
lux = lightMeter.readLightLevel();
statusText = (lux >= 0) ? "OK" : "Sensor error";
Serial.print(F("Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
5 parts: Nano CH340 Development Board (Soldered), GY-302 BH1750 Light Intensity Module – I2C Interface, LCD1602 16x2 Character LCD (blue, with I2C adapter), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 8 steps.
No. This page has the complete, tested code (art_studio_light_checker.ino). Install these libraries first: BH1750 and LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹482 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Character displays and I²C backpacks; Lux, lumens and the I²C bus.
Ideas that reuse this build: Study desk lamp checker and Digital lux meter. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Light=319lx Light=319lx Light=320lx Light=320lx Light=321lx
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.