LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA tired bulb or the wrong lamp position makes children squint at their books. Put the sensor where the page lies. Green means over 300 lx and the OLED shows the number, red means move the lamp or fit a brighter bulb.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Digital light sensor that reports brightness in lux, the same unit used for room and street lighting.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
Follow the colours: red is power, dark grey is ground, blue is a signal.
study_desk_lamp_checker.inoVerify & upload in Electrolark// Study desk lamp brightness checker
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "study-desk-lamp-checker"
#include <Wire.h>
#include <BH1750.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t LED_GREEN = 2;
const uint8_t LED_RED = 3;
BH1750 lightMeter;
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float lux = 0;
const unsigned long READ_EVERY_MS = 200;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 300; // 300 lx is a common target for reading and writing
const float HYSTERESIS = 60; // gap that stops rapid on/off switching
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Desk lamp"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 16);
oled.print(F("Light"));
oled.setTextSize(2);
oled.setCursor(0, 28);
oled.print(lux, 0);
oled.print(F(" lx"));
oled.setTextSize(1);
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void evaluate() {
if (!(lux >= 0)) { statusText = "Sensor error"; return; }
if (!alertOn && lux < ALERT_LEVEL) alertOn = true;
else if (alertOn && lux > ALERT_LEVEL + HYSTERESIS) alertOn = false;
statusText = alertOn ? "LAMP TOO DIM" : "Good light";
}
void setup() {
Serial.begin(115200);
Wire.begin();
if (!lightMeter.begin()) Serial.println(F("BH1750 not found"));
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
lux = lightMeter.readLightLevel();
evaluate();
Serial.print(F("Light="));
Serial.print(lux, 0);
Serial.print(F("lx"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRedLed(alertOn && (millis() / 250) % 2 == 0);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Check SDA and SCL are not swapped. An I²C scanner should show 0x23 (0x5C if the ADDR pin is tied high).
Check the wiring and power, then try again. A reading of 0 in a dark room is normal.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), GY-302 BH1750 Light Intensity Module – I2C Interface, 0.96" OLED Display 128x64 (I2C), 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (study_desk_lamp_checker.ino). Install these libraries first: BH1750, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹603 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Current-limiting resistors for LEDs; Drawing text on an I²C display; Lux, lumens and the I²C bus.
Ideas that reuse this build: Digital lux meter and Screen distance reminder. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Light=321lx, status=Good light Light=319lx, status=Good light Light=320lx, status=Good light Light=320lx, status=Good light Light=320lx, status=Good light Light=321lx, status=Good light Light=319lx, status=Good light Light=320lx, status=Good light
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.