LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsThe LM35 gives 10 millivolts for every degree Celsius, which makes it one of the easiest temperature sensors to learn. Tape it near a battery charger, a motor driver or a soldering stand; when it passes the limit the red LED flashes and the buzzer beeps.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Analog temperature sensor that outputs 10 mV for every degree Celsius, so no library or calibration table is needed.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Active buzzer with a built-in oscillator: apply power and it beeps at about 2.3 kHz.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_lm35_overheat_alarm.inoVerify & upload in Electrolark// LM35 overheat alarm
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-lm35-overheat-alarm"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t LM35_PIN = A0;
const uint8_t BUZZER_PIN = 2;
const uint8_t LED_RED = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
float tempC = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 40; // raise it for hot equipment, lower it for a cool room
const float HYSTERESIS = 3; // gap that stops rapid on/off switching
float readLm35C() {
long s = 0;
for (int i = 0; i < 20; i++) s += analogRead(LM35_PIN); // average out the noise
return (s / 20.0f) * VREF * 100.0f / ADC_MAX; // 10 mV per degree C
}
void setBuzzer(bool on) { digitalWrite(BUZZER_PIN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Temp "));
lcd.print(tempC, 1);
lcd.print(F(" C"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (!alertOn && tempC > ALERT_LEVEL) alertOn = true;
else if (alertOn && tempC < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "TOO HOT" : "Cool";
}
void setup() {
Serial.begin(115200);
lcd.init();
lcd.backlight();
pinMode(BUZZER_PIN, OUTPUT);
setBuzzer(false);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
tempC = readLm35C();
evaluate();
Serial.print(F("Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setBuzzer(alertOn && (millis() / 250) % 2 == 0); // intermittent beep
setRedLed(alertOn && (millis() / 250) % 2 == 0);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Keep the sensor away from the board regulator and warm parts, and add a 100 nF capacitor from OUT to GND.
The sketch already averages 20 samples. Add the capacitor and shorten the wire.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
Low-triggered module: invert the logic in setBuzzer().
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, LM35D Analog Temperature Sensor Module – Analog Voltage Output, LCD1602 16x2 Character LCD (blue, with I2C adapter), Active Buzzer Module 3.3–5V, Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 10 steps.
No. This page has the complete, tested code (atl_lm35_overheat_alarm.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹644 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Active vs passive buzzers; Analog temperature sensing and ADC resolution; Character displays and I²C backpacks; Current-limiting resistors for LEDs.
Ideas that reuse this build: DHT11 climate board. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Temp=150.0C, status=TOO HOT Temp=150.0C, status=TOO HOT
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.