LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsRotting waste makes methane, the gas in biogas. The MQ-4 reacts to it, so a covered compost bin or a small biogas demo model lets students see the reading rise as the mixture ferments. Green means normal, red means the level has passed your limit.
Use it only on small demo models in open air. Never test with real cooking gas or build a closed gas vessel.
This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Every main part of this project is an item on the public Package 1 equipment list, so a school lab that already owns Package 1 can build it without buying anything extra.
See the full Atal Tinkering Lab packages →
Geekobot is an independent shop, not endorsed by or affiliated with NITI Aayog or the Atal Innovation Mission. Item names follow the public AIM equipment list.
Tick anything you already have and the total updates.
Connects the Uno to your computer to upload code and power it
Heated sensor that responds to methane (CH₄) and natural gas such as biogas and CNG.
Classic 16-character, 2-line LCD with an I²C backpack, so it needs only two signal wires.
Green indicator LED for the normal state.; Red indicator LED for the alert state.
Follow the colours: red is power, dark grey is ground, blue is a signal.
atl_methane_biogas_checker.inoVerify & upload in Electrolark// Methane checker for a biogas model
// Geekobot project library · board: Arduino Uno
// Wiring diagram, parts list and build steps: Geekobot project page "atl-methane-biogas-checker"
#include <Wire.h>
#include <LiquidCrystal_I2C.h>
// ---- pins ----
const uint8_t METHANE_PIN = A0;
const uint8_t LED_GREEN = 2;
const uint8_t LED_RED = 3;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
LiquidCrystal_I2C lcd(0x27, 16, 2);
// ---- latest readings ----
int methanePct = 0;
const unsigned long READ_EVERY_MS = 1000;
unsigned long lastRead = 0;
bool alertOn = false;
const char* statusText = "Starting";
const float ALERT_LEVEL = 40; // set it just above the clean-air reading
const float HYSTERESIS = 8; // gap that stops rapid on/off switching
const unsigned long WARMUP_MS = 60000UL; // sensor warm-up
void setGreenLed(bool on) { digitalWrite(LED_GREEN, on ? HIGH : LOW); }
void setRedLed(bool on) { digitalWrite(LED_RED, on ? HIGH : LOW); }
void updateDisplay() {
lcd.setCursor(0, 0);
lcd.print(F("Methane "));
lcd.print(methanePct);
lcd.print(F("%"));
lcd.print(F(" "));
lcd.setCursor(0, 1);
lcd.print(statusText);
lcd.print(F(" "));
}
void evaluate() {
if (millis() < WARMUP_MS) { alertOn = false; statusText = "Warming up"; return; }
if (!alertOn && methanePct > ALERT_LEVEL) alertOn = true;
else if (alertOn && methanePct < ALERT_LEVEL - HYSTERESIS) alertOn = false;
statusText = alertOn ? "METHANE" : "Normal";
}
void setup() {
Serial.begin(115200);
lcd.init();
lcd.backlight();
pinMode(LED_GREEN, OUTPUT);
pinMode(LED_RED, OUTPUT);
}
void loop() {
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
methanePct = (int)(analogRead(METHANE_PIN) * 100L / ADC_MAX);
evaluate();
Serial.print(F("Methane="));
Serial.print(methanePct);
Serial.print(F("%"));
Serial.print(F(", status=")); Serial.println(statusText);
updateDisplay();
}
setRedLed(alertOn && (millis() / 250) % 2 == 0);
setGreenLed(!alertOn);
}
The sketch above runs here on a simulated Arduino Uno. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Normal: the heater needs a few minutes to settle. Wait before calibrating the threshold.
Adjust the contrast pot on the backpack. If still blank, change 0x27 to 0x3F.
LED is reversed; flip it. Check the 220 Ω resistor is in series.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
It stops the output flickering on and off when the reading hovers right at the limit. The output switches on at ALERT_LEVEL and only switches off once the reading has moved back by the hysteresis amount.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
8 parts: Uno R3 CH340G ATmega328p Compatible Development Board, Arduino USB-A to USB-B Data Cable for UNO/MEGA, MQ-4 Methane CNG Gas Detector Module – Analog & TTL Output, LCD1602 16x2 Character LCD (blue, with I2C adapter), 2 × Through-Hole LED Pack (Pack of 10), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (atl_methane_biogas_checker.ino). Install this library first: LiquidCrystal I2C.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹590 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Analog sensors, ADCs and warm-up drift; Character displays and I²C backpacks; Current-limiting resistors for LEDs.
Use it only on small demo models in open air. Never test with real cooking gas or build a closed gas vessel. This is a learning project, not a certified gas or smoke alarm. Keep a certified alarm installed.
Ideas that reuse this build: Gas sensor comparison station. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Methane=29%, status=Warming up Methane=29%, status=Warming up
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.