LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA good charger gives high current at first and tapers off as the battery fills. The ACS712 measures the current every 30 seconds and the Nano saves it with the time on an SD card. Plot the file to see how long your charger really takes.
Low-voltage DC circuits only. Do not charge Li-ion cells without a proper protection board.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Measures the current flowing through its two screw terminals with a Hall sensor, so the measured circuit stays electrically separate from the board.
Temperature-compensated real-time clock (±2 minutes a year) with a coin-cell backup, so the time survives power cuts.
Stores readings on a microSD card as a CSV file you can open in Excel or Google Sheets.
Follow the colours: red is power, dark grey is ground, blue is a signal.
battery_charger_current_logger.inoVerify & upload in Electrolark// Battery charger current logger
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "battery-charger-current-logger"
#include <Wire.h>
#include <RTClib.h>
#include <SPI.h>
#include <SD.h>
// ---- pins ----
const uint8_t CURRENT_PIN = A0;
const uint8_t SD_CS = 10;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
const float ACS_MV_PER_A = 185.0; // 5 A module: 185 mV per amp (20 A: 100, 30 A: 66)
float acsZero = 0; // output with no current, measured at start-up
RTC_DS3231 rtc;
// ---- latest readings ----
float currentA = 0;
const unsigned long LOG_EVERY_MS = 30UL; // one row per 0 s
unsigned long lastLog = 0;
bool cardOk = false;
float readCurrentA() {
long s = 0;
for (int i = 0; i < 100; i++) s += analogRead(CURRENT_PIN); // average out the noise
float mv = (s / 100.0f - acsZero) * VREF * 1000.0f / ADC_MAX;
float a = mv / ACS_MV_PER_A;
return fabs(a) < 0.05f ? 0 : a;
}
void writeRow() {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (!f) { Serial.println(F("Write failed")); return; }
DateTime t = rtc.now();
char stamp[20];
snprintf(stamp, sizeof(stamp), "%04d-%02d-%02d,%02d:%02d:%02d", t.year(), t.month(), t.day(), t.hour(), t.minute(), t.second());
f.print(stamp);
f.print(',');
f.print(currentA, 2);
f.println();
f.close();
}
void setup() {
Serial.begin(115200);
{ long s = 0; for (int i = 0; i < 200; i++) { s += analogRead(CURRENT_PIN); delay(1); } acsZero = s / 200.0f; } // switch the load off while the board starts
if (!rtc.begin()) Serial.println(F("RTC not found"));
if (rtc.lostPower()) rtc.adjust(DateTime(F(__DATE__), F(__TIME__))); // set from the upload time
cardOk = SD.begin(SD_CS);
Serial.println(cardOk ? F("SD card ready") : F("SD card not found"));
if (cardOk && !SD.exists("LOG.CSV")) {
File f = SD.open("LOG.CSV", FILE_WRITE);
if (f) { f.println(F("date,time,Current(A)")); f.close(); }
}
}
void loop() {
if (millis() - lastLog < LOG_EVERY_MS && lastLog != 0) return;
lastLog = millis();
currentA = readCurrentA();
Serial.print(F("Current="));
Serial.print(currentA, 2);
Serial.print(F("A"));
Serial.println();
if (cardOk) writeRow();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The zero point was taken with the load on. Switch the load off and reset the board.
Current flows the other way. Swap the wires on IP+ and IP−, or ignore the sign.
The coin cell is flat or missing. Some modules need the charging resistor removed when using a CR2032.
Check the card is FAT32, fully inserted, and CS is on the pin in the sketch.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), ACS712 Hall-Effect Current Sensor Module (5A), DS3231 Precision RTC Module with EEPROM, DFRobot Fermion MicroSD Card Module – SPI, microSD Memory Card Class 10 (16GB), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a intermediate project and takes about 2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (battery_charger_current_logger.ino). Install these libraries first: RTClib and SD.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹1,387 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Hall-effect current sensing; Real-time clocks and backup batteries; SPI devices and CSV logging.
Low-voltage DC circuits only. Do not charge Li-ion cells without a proper protection board.
Ideas that reuse this build: Solar charge logger and Phone charge current curve. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A Current=0.00A
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.