LPG gas leak alarm
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
Shop by category
Shop all componentsA healthy colony keeps its brood at about 35 °C. The waterproof probe slides between two frames in the brood box; the DHT22 reads the outside air. A brood reading that wanders far from 35 °C can mean the colony is queenless or weak.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Measures air temperature (±0.5 °C) and relative humidity (±2–5 %) on a single data wire.
Follow the colours: red is power, dark grey is ground, blue is a signal.
beehive_temperature_display.inoVerify & upload in Electrolark// Beehive brood temperature display
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "beehive-temperature-display"
#include <OneWire.h>
#include <DallasTemperature.h>
#include <DHT.h>
#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>
// ---- pins ----
const uint8_t ONEWIRE_PIN = 2;
const uint8_t DHT_PIN = 3;
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
DHT dht(DHT_PIN, DHT22);
Adafruit_SSD1306 oled(128, 64, &Wire, -1);
// ---- latest readings ----
float probeC = 0;
float tempC = 0;
float humidity = 0;
const unsigned long READ_EVERY_MS = 5000;
unsigned long lastRead = 0;
const char* statusText = "OK";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void updateDisplay() {
oled.clearDisplay();
oled.setTextSize(1);
oled.setCursor(0, 0);
oled.print(F("Hive"));
oled.drawLine(0, 10, 127, 10, SSD1306_WHITE);
oled.setCursor(0, 14);
oled.print(F("Probe: "));
oled.print(probeC, 1);
oled.print(F(" C"));
oled.setCursor(0, 24);
oled.print(F("Temp: "));
oled.print(tempC, 1);
oled.print(F(" C"));
oled.setCursor(0, 34);
oled.print(F("Humidity: "));
oled.print(humidity, 0);
oled.print(F("%"));
oled.setCursor(0, 56);
oled.print(statusText);
oled.display();
}
void setup() {
Serial.begin(115200);
probes.begin();
dht.begin();
if (!oled.begin(SSD1306_SWITCHCAPVCC, 0x3C)) Serial.println(F("OLED not found"));
oled.setTextColor(SSD1306_WHITE);
oled.clearDisplay();
oled.display();
}
void loop() {
if (millis() - lastRead < READ_EVERY_MS) return;
lastRead = millis();
probeC = readProbeC();
tempC = dht.readTemperature();
humidity = dht.readHumidity();
statusText = (probeC > -100 && !isnan(tempC) && !isnan(humidity)) ? "OK" : "Sensor error";
Serial.print(F("Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.print(F(", Temp="));
Serial.print(tempC, 1);
Serial.print(F("C"));
Serial.print(F(", Humidity="));
Serial.print(humidity, 0);
Serial.print(F("%"));
Serial.println();
updateDisplay();
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Check the DATA wire and the pull-up. The DHT22 needs at least 2 seconds between reads, so do not poll it faster.
Check SDA/SCL and try address 0x3D. Run an I²C scanner to confirm.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider.
Use a 5 V USB phone charger or a power bank into the board's USB port.
7 parts: Nano CH340 Development Board (Soldered), DS18B20 Waterproof Temperature Probe – 1m Cable, DHT22 Temperature & Humidity Sensor, 0.96" OLED Display 128x64 (I2C), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1 hour. The build on this page has 9 steps.
No. This page has the complete, tested code (beehive_temperature_display.ino). Install these libraries first: OneWire, DallasTemperature, DHT sensor library, Adafruit Unified Sensor, Adafruit SSD1306 and Adafruit GFX Library.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹631 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Drawing text on an I²C display; Single-wire digital sensors and why some sensors need slow polling.
Ideas that reuse this build: Wi-Fi beehive scale and Compost temperature monitor. They are listed under Take it further on this page.
A kitchen gas sniffer that beeps and flashes the moment LPG levels climb.
See the smoke level live on a crisp screen and get a loud warning when it spikes.
An infrared eye that spots an open flame and raises the alarm.
Walk into the room and it sounds the alarm: the classic first security build.
Learning project. Check every circuit and the datasheet of each part before you power it up.
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.