GPS speedometer and clock
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Shop by category
Shop all componentsBeekeepers learn a lot from weight: a hive gaining kilos in a week is on a nectar flow, a sudden drop can mean a swarm. Four 50 kg load cells under the corners of the hive stand (one 5 kg cell would be overloaded by a full hive) and a DS18B20 between the frames send both readings to the dashboard.
Tick anything you already have and the total updates.
Four half-bridge cells under the platform corners share the load, so the scale reads up to 200 kg
Waterproof stainless-steel probe that reads liquid or soil temperature from −55 to +125 °C (±0.5 °C).
Follow the colours: red is power, dark grey is ground, blue is a signal.
wifi_beehive_scale.inoVerify & upload in Electrolark// Wi-Fi beehive weight and temperature monitor
// Geekobot project library · board: ESP32-C3 SuperMini
// Wiring diagram, parts list and build steps: Geekobot project page "wifi-beehive-scale"
#include <HX711.h>
#include <OneWire.h>
#include <DallasTemperature.h>
#include <WiFi.h>
#include <WebServer.h>
// ---- pins ----
const uint8_t HX_DT = 10;
const uint8_t HX_SCK = 7;
const uint8_t ONEWIRE_PIN = 6;
HX711 scale;
const float CALIBRATION = 420.0; // raw units per gram: calibrate with a known weight
OneWire oneWire(ONEWIRE_PIN);
DallasTemperature probes(&oneWire);
// ---- latest readings ----
float grams = 0;
float probeC = 0;
const char* WIFI_SSID = "YOUR_WIFI_NAME"; // 2.4 GHz network
const char* WIFI_PASS = "YOUR_WIFI_PASSWORD";
WebServer server(80);
const unsigned long READ_EVERY_MS = 2000;
unsigned long lastRead = 0;
const char* statusText = "Starting";
const char PAGE[] PROGMEM = R"HTML(<!doctype html><html><head><meta name="viewport" content="width=device-width,initial-scale=1"><title>Beehive</title>
<style>body{font-family:system-ui,sans-serif;background:#0d093d;color:#fff;margin:0;padding:20px}h1{font-size:20px;margin:0 0 14px}
.g{display:grid;grid-template-columns:repeat(auto-fit,minmax(140px,1fr));gap:12px}.c{background:#1c1866;border-radius:14px;padding:14px}
.l{font-size:12px;opacity:.7}.v{font-size:28px;font-weight:700;margin-top:4px}button{margin-top:14px;padding:12px 18px;border:0;border-radius:10px;font-size:16px;background:#a9c5ea;color:#0d093d}
.s{margin-top:12px;font-size:13px;opacity:.8}</style></head><body><h1>Beehive</h1><div class="g" id="g"></div><p class="s" id="s">Connecting…</p>
<script>const F=[["grams","Weight","g"],["probeC","Probe","C"]];
async function tick(){try{const d=await(await fetch('/data')).json();document.getElementById('g').innerHTML=F.map(f=>'<div class="c"><div class="l">'+f[1]+'</div><div class="v">'+(typeof d[f[0]]==='boolean'?(d[f[0]]?'YES':'no'):d[f[0]])+' '+f[2]+'</div></div>').join('');
document.getElementById('s').textContent='Status: '+d.status+' · updated '+new Date().toLocaleTimeString();}catch(e){document.getElementById('s').textContent='Lost connection, retrying…'}}
setInterval(tick,2000);tick();</script></body></html>)HTML";
float readProbeC() {
probes.requestTemperatures();
return probes.getTempCByIndex(0);
}
void handleData() {
String j = "{";
j += "\"grams\":"; j += String(grams, 0); j += ",";
j += "\"probeC\":"; j += String(probeC, 1); j += ",";
j += "\"status\":\""; j += statusText; j += "\"}";
server.send(200, "application/json", j);
}
void handleRoot() { server.send(200, "text/html", PAGE); }
void evaluate() {
if (!(probeC > -100)) { statusText = "Sensor error"; return; }
statusText = "OK";
}
void setup() {
Serial.begin(115200);
scale.begin(HX_DT, HX_SCK);
scale.set_scale(CALIBRATION);
scale.tare(); // empty platform = 0 g
probes.begin();
WiFi.mode(WIFI_STA);
WiFi.begin(WIFI_SSID, WIFI_PASS);
Serial.print(F("Connecting to Wi-Fi"));
for (int i = 0; i < 40 && WiFi.status() != WL_CONNECTED; i++) { delay(500); Serial.print("."); }
Serial.println();
Serial.print(F("Open this address in your browser: http://"));
Serial.println(WiFi.localIP());
server.on("/", handleRoot);
server.on("/data", handleData);
server.begin();
}
void loop() {
server.handleClient();
if (millis() - lastRead >= READ_EVERY_MS) {
lastRead = millis();
grams = scale.get_units(5);
probeC = readProbeC();
evaluate();
Serial.print(F("Weight="));
Serial.print(grams, 0);
Serial.print(F("g"));
Serial.print(F(", Probe="));
Serial.print(probeC, 1);
Serial.print(F("C"));
Serial.println();
}
}
The sketch above runs here on a simulated ESP32-C3. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
Let it warm up for a minute and avoid touching the wires; re-tare after warm-up.
Place a known weight and adjust CALIBRATION until the reading matches.
The 4.7 kΩ pull-up is missing or DATA is on the wrong pin. Check the yellow wire.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Not directly; the board serves the page on your local network only. For remote access, send the readings to a cloud service such as MQTT, ThingSpeak or Blynk, or use a VPN into your home network.
No. ESP32-C3 and ESP8266 boards support 2.4 GHz networks only. Most routers broadcast both, so choose the 2.4 GHz name.
6 parts: ESP32-C3 SuperMini Development Board, HX711 with 4 × 50 kg Half-Bridge Load Cells and Combinator Board, DS18B20 Waterproof Temperature Probe – 1m Cable, Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a advanced project and takes about 3 hours. The build on this page has 8 steps.
No. This page has the complete, tested code (wifi_beehive_scale.ino). Install these libraries first: HX711, OneWire and DallasTemperature.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹458 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
1-Wire bus and pull-up resistors; Strain gauges, amplifiers and calibration factors.
Ideas that reuse this build: Kitchen scale and Garden station. They are listed under Take it further on this page.
A bike or car speedometer that needs no wheel sensor: satellites do the measuring.
Records where you went every five seconds, ready to open on a map.
Two boards, two radios: press the button at the gate and it rings indoors.
Check temperature, humidity and pressure from any phone on your Wi-Fi.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Connecting to Wi-Fi... Open this address in your browser: http://192.168.1.50 Weight=500g, Probe=26.0C
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.