Double-clap light switch
Clap twice and the lights come on. Clap twice again to switch them off.
Shop by category
Shop all componentsA first audio project: the DFPlayer reads MP3 files from a card and drives a small speaker. One button plays and pauses, the other two skip back and forward, and the knob sets the volume.
Tick anything you already have and the total updates.
The brain of the project
Works with the same pins and code as the original Arduino Nano.
Three momentary buttons, one leg each to a pin and the other legs joined to GND; the internal pull-ups do the rest.
A 10 kΩ knob that works as a voltage divider, giving an analog value you can map to anything.
Plays MP3 files from a microSD card through its own small amplifier, on command from the board over serial.
Connects straight to SPK1 and SPK2 (the module has a small 3 W amplifier)
Follow the colours: red is power, dark grey is ground, blue is a signal.
button_mp3_player.inoVerify & upload in Electrolark// Three-button MP3 player
// Geekobot project library · board: Arduino Nano
// Wiring diagram, parts list and build steps: Geekobot project page "button-mp3-player"
#include <DFRobotDFPlayerMini.h>
#include <SoftwareSerial.h>
// ---- pins ----
const uint8_t BTN_1 = 2;
const uint8_t BTN_2 = 3;
const uint8_t BTN_3 = 4;
const uint8_t POT_PIN = A0;
const uint8_t MP3_RX = 5;
const uint8_t MP3_TX = 6;
const int ADC_MAX = 1023; // 10-bit analog input
const float VREF = 5.0f;
DFRobotDFPlayerMini player;
// ---- latest readings ----
int potPct = 0;
SoftwareSerial mp3Serial(MP3_RX, MP3_TX);
const int VOLUME = 18;
bool playing = false;
int lastVol = -1;
// returns 0 when nothing is pressed, else 1-3
int pressedButton() {
if (digitalRead(BTN_1) == LOW) return 1;
if (digitalRead(BTN_2) == LOW) return 2;
if (digitalRead(BTN_3) == LOW) return 3;
return 0;
}
void setup() {
Serial.begin(115200);
pinMode(BTN_1, INPUT_PULLUP); pinMode(BTN_2, INPUT_PULLUP); pinMode(BTN_3, INPUT_PULLUP);
mp3Serial.begin(9600);
if (!player.begin(mp3Serial)) Serial.println(F("DFPlayer not found: check wiring and card"));
player.volume(VOLUME);
player.playMp3Folder(1); playing = true;
}
void loop() {
int p = pressedButton();
if (p == 1) { if (playing) player.pause(); else player.start(); playing = !playing; } // 1 = play / pause
if (p == 2) { player.previous(); playing = true; } // 2 = previous
if (p == 3) { player.next(); playing = true; } // 3 = next
if (p) delay(300);
int v = map(analogRead(POT_PIN), 0, ADC_MAX, 0, 30); // knob = volume
if (abs(v - lastVol) > 1) { lastVol = v; player.volume(v); Serial.print(F("Volume ")); Serial.println(v); }
delay(20);
}
The sketch above runs here on a simulated Arduino Nano. Move the sliders for the sensors and buttons it reads, and watch the Serial monitor, display and outputs change.
It is rotated 90°; turn it so the legs span the gap.
The wiper is on an outer pin. Move the signal wire to the middle leg.
Check TX goes to the board RX pin and RX to the board TX pin, and that the card is inserted and FAT32.
Tracks are numbered by the order files were copied. Use the mp3 folder with 0001.mp3 names so the numbers are fixed.
Open the Serial Monitor at 115200 baud and check for messages. Make sure you chose the right board and port in the Arduino IDE.
Close other programs using the serial port, try another USB cable (some are charge-only) and press reset just before uploading.
Yes. Most of the code works unchanged on an ESP32 with the ESP32 board package. Watch for 5 V modules: ESP32 pins are 3.3 V, so 5 V output signals need a resistor divider. Analog readings run 0–4095 instead of 0–1023, which the ADC_MAX constant handles.
Use a 5 V USB phone charger or a power bank into the board's USB port.
9 parts: Nano CH340 Development Board (Soldered), 3 × Tactile Push Button Switch, 16mm Rotary Potentiometer 10kΩ (Linear), DFPlayer Mini MP3 Player Module (MP3-TF-16P), Mini Speaker 8Ω 1W 40mm, microSD Memory Card Class 10 (16GB), Resistor Assortment Kit (30 Values), Solderless Breadboard (830 points) and Dupont Jumper Wires (40 pcs). Tools: Digital Multimeter and Wire Stripper and Cutter. On this page you can tick the parts you already have and add only the rest to your cart.
It is a beginner project and takes about 1–2 hours. The build on this page has 9 steps.
No. This page has the complete, tested code (button_mp3_player.ino). Install this library first: DFRobotDFPlayerMini.
Yes. The Run it panel under the code runs this exact sketch on a simulated board. Move the sliders or press the buttons for the sensors it reads, and the Serial monitor, display and outputs react as they will on the real build. It is a simulation, so real readings depend on your parts and wiring.
About ₹915 for the parts at the prices on this page, plus tools if you do not have them. Quantity price breaks lower the cost when you build several.
Pull-ups and debouncing; Serial-controlled audio playback; Voltage dividers and analogRead().
Ideas that reuse this build: Museum exhibit guide and Keypad mini piano. They are listed under Take it further on this page.
Clap twice and the lights come on. Clap twice again to switch them off.
Plays a friendly ding-dong whenever someone walks into the shop or room.
Beeps and flashes any message in Morse, or key your own by hand.
Turn a membrane keypad into a two-octave piano.
Learning project. Check every circuit and the datasheet of each part before you power it up.
Volume 14
A simulation of the sketch above, so you know what to expect. Real readings vary with your parts and wiring.